Rascal Vantage X User manual

Electric Mobility Euro imited, Canal Way, Ilminster , Somerset TA19 9DL
Telephone [phone] www.electricmobility.co.uk Issue 1 04/2013
Rascal Vantage and
Vantage X Scooters
Owner’s Manual & Service Record
Rascal Vantage and
Vantage X Scooters

Electric Mobility Euro Ltd has designed these two durable scooters for outdoor short to medium range use.
The Vantage and Vantage X scooters are of fixed frame construction and not designed to be fully
dismantled for transportation, however they are compact enough to fit into some larger cars, MPVs and vans.
Provided that your scooter is maintained and operated in accordance with this manual it should last for many
years, and provide you with freedom and independence.
Please read this manual thoroughly before using your scooter. If you have any doubts about warnings or
instructions, ask your dealer for an explanation. If at any time you feel you may not be able to control your
scooter safely, do not drive it, and consult your dealer for a solution. If you think your scooter may be damaged,
do not drive it and contact your dealer for advice.
We suggest that you keep this owner’s manual in a safe place as it contains essential safety, operation and
maintenance information for your scooter.
2
2
Notice
All Electric Mobility Vehicles are sold through authorised dealers. Make sure your dealer demonstrates all
the features of the product prior to, or when, it is delivered.
Warning!
This manual contains important safety notices. Please take time to read and understand them. Ignoring
them may endanger you or others.
Rascal Vantage and Vantage X Scooters Owner's Manual and Service Record
Rascal Vantage and
Vantage X Scooters

3
Contents Dealer information 4
Features and layout 4
Safety information 5
Intended use 5
Safety Information 6
Controls 8
Freewheel Device 10
Brakes 10
Armrest adjustment 11
Swivel seat 11
Tiller folding 12
Transferring in and out of your scooter. 13
Operation 13
Driving the vehicle 14
Driving the vehicle - hazards 15
Transporting your scooter 16
Assembling your scooter following transportation 18
Battery charging 19
User maintenance 21
Servicing & maintenance 21
Scooter Diagnostic Functions 22
Troubleshooting guide 23
Additional safety information 23
Additional information 24
Frequently asked questions 24
Engineers checklist 25
Guarantees 26
Technical information regarding EMI 27
Technical specification 28
Service log 30
Brochure request 31
Dealer information - Guarantee Card 31
Notes 33

4Rascal Vantage and Vantage X Scooters Owner's Manual and Service Record
Dealer Information
For product information see serial number plate on the seat post under the seat.
Manufacturer
Electric Mobility Euro Limited
Canal Way, Ilminster, Somerset TA19 9DL
Company Registration in England No. 2419231
Features and ayout
Photo shows the Rascal Vantage X scooter. See the Technical Specifications section of this manual
for detailed information.
This is your contact number
for service and support
Dealer Stamp
Telephone
Email
Product Model Number
Serial Number
Date of Purchase
Owner
Rear view mirrors
Charging point
Fold up / width
adjustable armrestsEmergency braking system
Finger control lever
Tiller adjustment /
variable tiller angle
Fold down backrest
Integrated battery
enclosure
Pneumatic tyres
on alloy rims
Detachable
shopping basket
Freewheel lever

5
Safety Information
Read this manual thoroughly before driving or operating the vehicle.
If you have any doubt about the content of this manual phone your dealer to resolve the problem. Please read
this manual, and ensure your scooter is serviced regularly.
Book symbol This symbol appears on the product. Please read this product manual before
assembling or operating the scooter.
Pinchpoint symbol Wherever you see this sign there is a nearby risk of injury owing to a pinch or
crushing point.
Tip symbol This sign indicates advice on how to get the most from your scooter.
© 2013 Electric Mobility Euro Ltd.
No liability is assumed with respect to the use of any information contained in this publication. While every precaution
has been taken in the preparation of this publication Electric Mobility Euro Ltd. assumes no responsibility for errors or
omissions nor is any liability assumed for damages resulting from the use of information contained in this publication.
This publication, as well as the operational details described herein, is subject to change without notice.
Intended use of the vehicle/s
The Vantage and Vantage X scooters are designed for use by adults with a disability (up to the maximum
recommended weight - see Technical Specification Sheet) who require a robust, comfortable scooter that is ideal
for shopping and other visits. The Rascal Vantage X is a medium range 6mph scooter which is suited for travel
on public roads when this is required. The Rascal Vantage is similar to the Vantage X, however it is not suitable
for use on public roads and is limited to 4 MPH by design. When driven on pavements and other pedestrian
areas, your scooter should be set on the low preset speed setting (max 4 mph - see controls section of this
manual). The Rascal Vantage and Vantage X scooters have lighting to enable them to operate in the dark. Both
models of scooter are designed to operate on pavements and other hard surfaces and can mount kerbs and
other obstacles as defined in the Technical Specifications section of this manual. - high kerbs should be avoided.
Users could endanger themselves and others if they are not capable of driving their scooter safely. Dealers will
advise on the most suitable vehicle from the Electric Mobility range, but it is the user's responsibility to ensure
that they have the manual dexterity to drive the vehicle, adequate sight and hearing to perceive danger in time,
and can at all times operate the scooter safely in the expected conditions. If in doubt we suggest you consult a
healthcare professional and your nearest dealer for advice on the most suitable scooter for your particular
condition. Users should also regularly assess their ability to operate their vehicle safely.
The Rascal Vantage and Vantage X scooters should not be used on loose, heavily rutted or slippery surfaces
such as grass.
Within this manual there are important safety notices. They are clearly marked with the sign (left)
Make sure that you understand all these notices. If you have any doubt, contact your dealer.

6Rascal Vantage and Vantage X Scooters Owner's Manual and Service Record
Safety Information
General Warnings
Warning ! The operation of scooters can endanger the life of the driver or third parties. Any driver should
always be fully capable of operating this vehicle safely.
Warning ! Sitting for long periods may increase the chance of thromboses or pressure sores. Users prone to
such conditions are advised to take medical advice.
Warning ! The Rascal Vantage and Vantage X scooters have been designed and tested for drivers with
weights up to those in the Technical Specification section of this manual. These weights should
never be exceeded.
Warning ! Do not exceed the specification; do not modify your scooter or use it other than as a scooter.
Warning ! Passengers, including children, should never be carried.
Warning ! Electromagnetic interference may affect the driving of your scooter
• Do not operate devices such as CB radios or mobile phones while the vehicle is switched on.
• Avoid getting close to transmitter masts, such as television and radio stations.
If your vehicle ever starts to operate by itself switch it off and report this to your Dealer.
Warning ! The operation of any scooter may affect sensitive electronic circuits such as alarm systems or
automatic doors in shops.
Driving
Before driving, refer to ”Driving Your Vehicle” … later in this manual
Warning ! Ambient Operating Temperature Range. Do not use your scooter in temperatures outside the
range stated in the specifications section of this manual. Driving in very hot or very cold conditions
can make driving more hazardous.
Warning ! Freewheel Device/Mode. Before getting on your scooter always check that the freewheel lever is
in the Drive position. When the freewheel lever is in the freewheel position, the main brakes on your
scooter will not function. Extra care should be taken with your scooter when it is in freewheel
mode as it could move without warning. You must never sit on or try to ride your scooter when it is
in freewheel mode as serious injury or death may result.
NEVER SIT ON THE SCOOTER WHEN IN FREEWHEE MODE.
Warning ! Transferring On and Off. Do not attempt to get on or off your scooter unless it is switched off, at
rest, and on a stable, level surface. Never get on or off on a hill.
Warning ! Damage. Before driving off, check the scooter for damage, particularly that which could affect the
controls, wheels, freewheel function and/or drive motor.
Warning ! Footrest. Before switching on the scooter, always make sure that your feet are safely on the
footrest area. If you drive forward with your feet still on the ground, they could become trapped
under the scooter and serious injury may result.
Warning ! Armrests. Do not use the armrests as a support for your entire weight when getting in or out of the
scooter. Make sure the armrests are lowered and secure before you start off otherwise you may fall out.
Warning ! Entanglement. Do not wear clothing or carry items on the scooter that could become entangled in
wheels or other moving parts whilst operating the scooter. Severe injury may result.

7
Warning ! Battery Charge evel. Before driving off, always check the battery indicator. If you are in any
doubt, ensure all the batteries are fully charged before starting on a journey.
Warning ! Castoring. Be aware that, if you set off when the front wheels are not straight, the initial movement
could be partially sideways.
Warning ! Power. Unless there is an emergency, do not switch the power off when moving. The Scooter may
stop very suddenly. Release the forward / reverse control and the scooter will come to a controlled stop.
Warning ! Slopes. On steep slopes the scooter could topple over. Always try to avoid crossing a slope. If you
have to cross a slope, take great care to avoid tipping. Never make sharp turns on slopes. Never
drive on slippery or icy slopes. - If you are not comfortable with the hill gradient, consider an
alternative route. See “Driving Your Vehicle” – Hazards for more advice.
Warning ! Kerbs. You should always try to avoid driving up or down kerbs as this may cause the scooter to
topple. Use access ramps wherever possible. Never attempt to climb or descend kerbs greater
than that noted in the Technical Specification. If you have to climb or descend a low kerb, always
tackle it straight on. See “Driving Your Vehicle” – Hazards for more advice.
Warning ! Speed. Turning at maximum speed might cause the scooter to topple over. Always slow down for
turns. Always slow down when amongst pedestrians and ensure you do not run into them.
Warning ! Stopping. If the scooter stops suddenly when turning, it might topple. Try not to brake when
turning. Always take particular care when turning.
Warning ! Reversing. Always take particular care when reversing the scooter as injury to other people may
occur if safe distances are not maintained.
Warning ! eaning Over. Do not lean sideways, as this could cause the scooter to topple.
Warning ! Escalators. Never drive the scooter onto an escalator as this could cause the scooter to topple
and result in severe injury.
Warning ! Roads. In the United Kingdom, Mobility scooters are not permitted on dual carriageways without
an additional amber warning beacon being fitted. Never take your scooter on a Motorway. For more
information please refer to the Highway code.
Warning ! Driving in Poor Visibility. Scooters are not easily seen. Always turn your lights on in poor visibility
or when travelling on roads. Consider wearing a high visibility jacket to warn others of your presence.
Warning ! Carrying Items. Do not carry or attach anything to the handlebars or controls as this could affect
the driving safety.
Warning ! Hot Surfaces. If the scooter is left out in the sun, surfaces could become extremely hot. Always try
to park the vehicle in the shade.
Warning ! Seats in Vehicles. These scooters are not suitable for use as a seat for an occupant when in a
motor vehicle.

8Rascal Vantage and Vantage X Scooters Owner's Manual and Service Record
Controls Rascal Vantage X shown.
Before driving your vehicle it is important to familiarise yourself with the controls. Do not attempt to drive the
vehicle before reading the rest of this Owner’s Manual.
Dashboard Description
1. Battery Indicator: This indicator shows the level of charge in the batteries. When all segments are shown
the batteries are full. As the charge level of the batteries depletes, so the number of lit segments will drop.
Note When the vehicle is climbing a steep incline or starting off, the level may drop momentarily; this is normal.
2. Speed Control: This controls the preset top speed of your scooter. When the knob is turned anticlockwise
to the left, this is its slowest speed, marked by a tortoise. As the knob is turned to the right the speed will
increase to a maximum, marked by a hare. Set the speed before you move off. Do not adjust the speed
control dial when the vehicle is moving.
3. Power On Indicator: When the ignition key is inserted into the scooter and turned to the "on" or "I"
position, the LED array will illuminate.
Tip: If a LED flashes , a d persists, this may i dicate a fault. A key to the fault codes ca be fou d i the
"Scooter diag ostic fu ctio s" sectio of this ma ual. A commo "fault" is that the scooter has bee left i
freewheel mode. Tur the key to the "0" or off positio , dise gage the free-wheel mode a d tur the key back
to the o or "I" positio .
4. Horn: Press the button and the horn will sound.
3
5
2
1
7
8
9
6
6
10
4
11

9
5. Ignition Key: Remember to remove the key when not in use. Do
not leave the ignition on when not in use, especially when charging
the vehicle (Fig.1). Note: You may need to press the ignition key
gently inwards before it will allow itself to be turned.
6. Finger control: To operate, turn on the ignition. Pull the right hand
lever towards you and the machine moves forward. The more you
pull the lever the faster the scooter goes. To brake, release the lever.
Again the faster the lever is released the quicker you will stop. To
reverse, pull the left lever towards you. Do not pull both levers at
once. Note The controls can be changed for customers with a
left-hand bias. Please contact your local dealer for information.
7. ighting control: To switch on the scooter front and rear lighting press the lighting switch once, to turn it
off, press the switch a second time.
8. Hazard lights: In an emergency or during a break-down, the hazard lights should be switched on.
Press the hazard light button once to switch on - All turn indicators will flash together. Press the button for
a second time to switch the hazard lights off.
9. Indicator (left turn): Press the left hand side of the indicator button once to start the left turn indicator
flashing, to switch off, re-center the switch.
10. Half speed switch: This button is marked with a tortoise. When travelling in pedestrian areas (not on the
road) this switch can be pressed to limit the maximum scooter speed to 50% of the value pre-selected by
the speed control (2) knob. This means that the scooter will not be able to travel at more than 4mph. To
turn this function off, press the switch for a second time. Only featured on Vantage X model.
11. Indicator (right turn): Press the right hand side of the indicator button once to start the left turn indicator
flashing, to switch off, re-center the switch.
12. Battery cut-out: Your scooter is equipped with a battery cut-out
(Fig.2) that is designed to operate in the unlikely event of an electrical
or electromechanical overload and is located beneath the rear
removable "boot" panel of the scooter (Fig.3). If this activates, all
power will be cut from the batteries to the scooter. This device can
be re-set by pressing the button shown in the illustration. Should it
activate for a second time please seek advice from your dealer.
Charging Point: The charging point is situated on the left hand side
of the scooter tiller. See the Charging section for further instructions.
Note: The Rascal Vantage does not have all of the features shown above.
2
3
1

10 Rascal Vantage and Vantage X Scooters Owner's Manual and Service Record
Freewheel Device
When the vehicle is switched off the brakes are automatically
engaged. This is called “Failsafe Braking”. Also, if the batteries are
flat, the brakes are applied. There may be occasions where you may
wish to move the vehicle without power. To do this there is a
Freewheel Device fitted.
The Freewheel device allows the vehicle to be pushed without power.
To activate, first locate the lever. When standing behind the scooter, it
is located on the right hand side of the rear of the vehicle (see Fig.4)
• Make sure the On/Off (ignition) key is in the off position.
• Move the lever UPWARDS The vehicle can now be pushed in Freewheel.
• Move the lever DOWNWARDS to engage drive. The vehicle is now braked. This is the normal
operating position.
• IF YOU ARE NOT COMP ETE Y SURE OF THIS FEATURE CONTACT
YOUR DEA ER BEFORE OPERATING THE SCOOTER.
NOTE: To avoid excessive strain on the tiller / handlebar assembly, never push or pull the scooter in
freewheel mode if a user is on-board. Push the lever UPWARDS to engage freewheel mode. Pull the lever
DOWNWARDS to engage Drive mode.
Warning! If the freewheel device is in “freewheel” mode the braking is disabled. Never select the
freewheel mode if the Scooter is on a slope or could be pushed onto a slope.
Brakes
There are 3 braking systems. The first works with the finger controls. When the finger control is released the
scooter will automatically brake and bring the scooter to a stop. When the scooter stops the automatic parking
brake will engage. This will stop the vehicle rolling forward or backward. When you start the brake will automatically
disengage. If the battery should go flat the brakes automatically engage. Note that even when freewheel is
selected, a secondary regenerative braking system is applied automatically to limit the maximum speed.
You may notice this system causing drag when moving the scooter in
freewheel mode.
The third braking system is a twin rear drum brake that can be used in
emergencies. This braking system is controlled by pulling/compressing the
lever on the right hand side of the handle bars/ tiller (see Fig.5). The more
pressure you apply to the lever the heavier the braking effect will be. This
braking system applies even braking to both back wheels making it one of
the safest designs on the market. 5
4
Warning! Do not use the emergency brake for normal driving.

11
Warning! Never attempt to disassemble or adjust the braking system. Any maintenance must be carried
out by your authorised dealer.
Armrest adjustment
When preparing to sit on the scooter, first lift one armrest to enable easy access (Fig.6). When riding always have
the armrests in the down position. Avoid pinching fingers as you lower the armrest. If you require more room in
the width of the seat, undo the knobs at the rear of the seat (Fig.7). Slide the armrests in or out to suit. Tighten
both knobs to lock the armrest width adjustment in place. To ensure that the user is sitting centrally, the armrests
should always be adjusted to be equidistant from the centre of the seat.
Warning! Never drive with the armrest up or with the armrest knob loose.
67
Swivel seat
This allows easy access
1. To operate, locate the release lever under the seat (Fig.8).
2. Pull the lever up and the seat will release allowing it to rotate.
3. Release the lever and the seat should lock automatically, but always
check it has.
Warning! Do not use this device if the vehicle is on a slope. Always check the seat is locked in the
forward position before driving the vehicle.
8

12 Rascal Vantage and Vantage X Scooters Owner's Manual and Service Record
Warning! Before driving, always check that the tiller is securely in the comfortable upright driving
position. Safe steering may be impossible if you do not !
Tiller Folding
The tiller can be folded down for transporting and storage. Take care when
lowering the tiller not to pinch your fingers.
• Push the tiller release lever downwards as shown - this will allow
the tiller to be put in the desired position. (Fig.9)
• ower the tiller so that it is in its lowest position (Fig.10).
• Release the tiller lever and the tiller will be set in that position.
Tip: The tiller ca be adjusted i the same way to achieve a comfortable
drivi g positio .
9
10

13
Transferring In And Out Of The Scooter
If you feel at all uncertain about getting in or out of the scooter seek assistance.
Transferring into the Scooter from the Front
Before getting in:
• Make sure that the scooter is on a level surface, and it is not in
Freewheel mode.
•Make sure the brakes are engaged - try to push the scooter a little
to verify that the brakes are working.
• Ensure that the inition key is turned off. (The LED display on the
dashboard will not be lit or flashing)
• Ensure that the handlebar/tiller adjustment and seat
adjustments are fully tightened and that any accessories are
properly fitted and secured.
• The seat should be facing forwards.
• Adjust the handlebars/tiller so that the front wheels are facing forward.
• Raise one armrest to make access easy. (Fig.11)
You are now ready to get in:
• Approach the seat from the side and step on to the footrest area of the scooter. you should now be
standing on the scooter platform facing forwards and with the seat behind you. With your back to the seat,
you can steady yourself using the other armrest and then lower yourself gently into the seat.
• Now lower the armrest back into position.
Getting out of the Scooter:
• Before getting out of the scooter, be sure that it is on a level surface and the power key is switched to the
off position. - If you feel uncertain about getting out, seek assistance. Move the handlebar/tiller so that the
front wheels are facing directly forwards.
• Raise one armrest.
• Raise yourself out of the seat to a standing position using the armrest to provide you with additional stability
if required. (Do not put your full weight on the armrests).
Tip: You may fi d it easier to swivel the seat to get i a d out of the scooter. If so please refer to "Swivel Seat"
sectio of the ma ual. Usi g this method, you ca stabilise yourself usi g both armrests.
11
Operation
Before using the scooter you should make sure that
• The battery is fully charged. (The battery level indicator will show all segments lit)
• There is no sign of damage to the scooter. All adjustment thumb-wheels are fully tightened.
• All accessories are properly attached.
• That you are capable of controlling the scooter at all times.
Kerbs and Obstacles: Try to avoid taking the scooter over obstacles or kerbs. Tackle obstacles head on.
Bad Weather: We suggest that it is better to stay at home in bad weather. Remember that you can become wet
and cold. Suitable clothes should always be worn. A high visibility jacket should be considered if you are in poor
visibility conditions or intending to drive on the road. Remember not to use the scooter in poor light or darkness.

14 Rascal Vantage and Vantage X Scooters Owner's Manual and Service Record
Driving the Vehicle
1. Before you set out, do check the weather forecast. We suggest that you make sure you are wearing
suitable clothing, whether your journey is long or short.
2. Range. Your scooter has a limited range. Always ensure that your planned journey does not exceed the
maximum range in the Technical Specification Sheet and that your battery is fully charged.
3. If you are taking medication check with your doctor or physician that your ability to control the vehicle
will not be impaired and do not drink alcohol and drive.
4. Only use the vehicle for the purpose its intended for. Do not drive through water or on slippery
surfaces; do not transport more than one person; do not tow other vehicles or carry excess weight.
5. Check that the freewheel lever is not in the freewheel position / mode.
6. Check the battery charger is disconnected.
7. Check that you are properly seated.
8. Check the backrest is correctly adjusted and locked in position.
9. Check that none of the items in your storage compartment are likely to fall out or become
entangled in the scooter wheels or other mechanisms.
10. Ensure your feet are securely on the footrest areas.
11. Check you have adjusted the seat as instructed in this manual.
12. Make sure the way ahead is clear.
13. Switch on the power. Check the battery level indicator is showing a high charge level.
14. Speed Control. Set the speed control to a low setting.
15. Gently actuate the finger controls (either forward or reverse) and steer in the direction required.
The vehicle will now move off. The further you pull the paddle (either forward or reverse) the faster the
vehicle will go.
16. To brake, return the paddles to the starting/neutral position. If you become unsure or feel
unsafe release the paddles immediately.
Note: Never push or pull both paddles at the same time as you may damage your scooter's control
system and cause it to behave erratically.
17. As you get accustomed to the power you can increase the speed.
Warning! Read this before driving the vehicle! Whether or not this is your first mobility
vehicle, please read these guidelines as all vehicles differ. Failure to do this may cause damage to you,
a third party or the vehicle.

15
18. Switch off when not in use. To conserve your batteries and prevent the vehicle accidentally moving,
always switch off the power when your Scooter is not in use. (On/Off or ignition key).
Tip: If you do leave your scooter switched o for a prolo ged period of time without usi g it, it will e ter a
sleep mode to co serve power. To reactivate the scooter, the O /Off key will eed to be tur ed to the "Off"
positio a d the back to the "O " positio .
Driving the vehicle - hazards
1. Getting on and off the vehicle: When getting on make sure that the vehicle is on level ground, and not
in freewheel mode. Ensure that the armrests are secure. When getting off, park on level ground, turn off
the ignition and remove the key before leaving your seat. Make sure you get off the vehicle in a safe area.
2. Tiller Position: Drive with the tiller in an upright position that feels comfortable with the controls in easy reach.
3. Kerbs and Obstacles: Try to avoid kerbs and obstacles. Never ride up or down kerbs or obstructions higher
than that in the Technical Specification Sheets. Always tackle obstacles head on. Use ramps wherever possible
and ensure that all wheels will fit on the ramp. Always try to avoid crossing a slope. If you have to cross a
slope, take great care to avoid tipping. Never make sharp turns on slopes or back down a slope.
4. Hills & Slopes: Going Up Hill. ean forward when going up. Make sure you have enough speed to
climb the slope. Do not stop or turn the vehicle around. If you have to turn while climbing an incline,
keep going until you reach a level area. If you have to start on an incline, lean forward and apply power
slowly – do not start and stop. If you are not comfortable about tackling a gradient, consider an
alternative route. Note Always check that the battery level is high; going up hill takes a lot of energy. If the
level drops too low the vehicle will cut out leaving you stranded.
5. Hills & Slopes: Going Down Hill. ean back in the seat when going down, and turn the speed
control dial to low. If you are not comfortable about tackling a gradient, consider an alternative route.
Try to avoid crossing slopes – always drive straight up or down the slope.
NEVER BACK DOWN A S OPE!
6. Terrain: Do not drive your vehicle across deep, soft or slippery terrain ( for example, soft dirt, sand, or loose
gravel). You could get stuck. Also avoid rutted, bumpy ground and try to keep to well prepared surfaces.
7. Turning: Always slow down before a turn; turning at speed can cause the scooter to topple. Look in the
direction you are travelling – If there is a blind corner sound the horn.
Warning! Before driving the scooter you should be aware that, under certain circumstances it could
become unstable and tip over. Your scooter has been designed to operate on hard, even surfaces and
should not be used on very rough or rutted terrain. Do not exceed the maximum safe slope recorded in
the Technical Specifications.

16 Rascal Vantage and Vantage X Scooters Owner's Manual and Service Record
8. Turning Circle: Practice manoeuvring your scooter so you can judge the turning circle. This is important
to avoid tipping off kerbs or for negotiating tight spaces.
9. Bad Weather: If it is snowing or icy stay at home! Remember that ice, snow and slippery surfaces such
as manhole covers, wet grass and drains could affect braking and steering. Use caution at all times.
10. Tyres: Your vehicle is fitted with pneumatic tyres. Should they become damaged or punctured they
should be replaced by your dealer. Do not attempt to replace them yourself.
11. Pavements: It is illegal to drive at more than 4 m.p.h. on the pavement. When driving on pavements and in
pedestrian areas, make sure you press the "tortoise button" on the dashboard - this will automatically limit
the scooter to the maximum legal limit of 4mph. Always slow down in crowded areas and take care not to
collide with pedestrians.
12. Shower Rooms or Washing: Never take your scooter into a shower or steam room, and never hose or
jet-wash it down. Its sensitive electronics could malfunction if they get wet or damp.
13. Immersion: Never enter large puddles or areas of water where the depth and/or current is unknown.
Immersion or partial immersion of the scooter may damage it and could leave you stranded.
Transporting your Scooter
Warning! Dismantling the scooter involves lifting and handling heavy parts. Weights are given in the
Technical Specification; consider if you need help in handling parts before you try to lift them. Your scooter is
not designed for unassisted loading into and out of a car or similar vehicle. Specialist ramps and hoists are
available for transferring the scooter into and out of a vehicle. Contact your dealer for advice on how best to
transport your scooter in your particular vehicle.
Warning! Pinching or Crushing. Be careful to avoid being pinched or having your hands crushed when
lifting or handling parts. Wear gloves whenever possible. Special attention should be paid when raising and
lowering armrests or rotating/handling the front wheels when dismantling or during re-assembly for
transportation in a vehicle.
Warning! This vehicle is not suitable for use as a seat for an occupant in a motor vehicle.
Warning! Do not stand the scooter up on its ends or sides as it may become unstable and topple
causing an injury.
To transport your scooter you may need specialist lifting equipment and / or ramps. Your dealer will be able to
advise you on the best solution for your particular needs. It is possible to fold the tiller down and either fold the
seat forwards or remove it completely for storage or to assist in loading into a vehicle using ramps or a hoist.
To remove the seat:
1. Fold the seat-back flat and grasp the seat as shown (Fig.12) and lift it away from the scooter frame.
Tip: Removi g the seat may be easier if you first use the seat swivel fu ctio to rotate the seat so it is at
90˚ to the scooter before lifti g.

17
12 1413
Warning! Do not attempt to lift any of the scooter components unless you are capable of doing so. The
weight for each component is shown in the Technical Specification (page 27)
Warning! Do not attempt to lift the chassis un-assisted - back or other injury may result!
To fold the tiller:
1. Push the tiller release lever downwards as shown - this will allow the tiller to be put in the desired
position. Release the tiller lever and the tiller will be set in that position. (Fig.13)
Tip: Alter atively the seat a d tiller ca be folded towards each other to reduce overall height a d facilitate
easier storage of the scooter (Fig.14)

18 Rascal Vantage and Vantage X Scooters Owner's Manual and Service Record
Assembling your Scooter following Transportation
After removing your scooter from a vehicle and placing it on level ground,
check it is undamaged before starting to assemble it as follows
1. Push the tiller release lever downwards as shown - this will allow
the tiller to be put in the desired position. Release the tiller lever and
the tiller will be set in that position. (Fig.15)
2. Grasp the seat on both sides and insert the seat post into the
seat-post tube in the chassis (Fig.16).
3. Fold the seat-back into the vertical position (Fig.17).
4. Refit the basket and lock in position by pushing down on the top edge gently (Fig.18).
Finally check the scooter is not damaged and it is properly assembled, checking that the battery indicator shows
the battery is charged, the freewheel lever is in the drive position, the seat is locked in place and the finger
controls operate correctly. You are now ready to drive the scooter away.
Warning! Assembling the scooter involves lifting and handling heavy parts. Your scooter is not designed
for unassisted loading into and out of a car or similar vehicle. Specialist ramps and hoists are available for
transferring the scooter into and out of a vehicle. Your dealer should advise you on the best way to assemble
your scooter.
Warning! Pinching or Crushing. Be careful to avoid being pinched or having your hands crushed when
lifting or handling parts. Wear gloves whenever possible.
Warning! Never unload your scooter on sloping or uneven ground. It could run down the slope and
injure someone.
15 17
18
16

Battery Charging
The charging socket is located on the upper left-hand side of the tiller. Rotate
the protective cover and push in the plug. When the vehicle is charged remove
the plug, and reposition the protective cover to keep the water out (Fig 20).
The battery charger has coloured charge status indicating LEDs / lamps (Fig 21).
When the charger is connected and switched on the first lamp will illuminate
green. If no mains power is present, no lamps will be lit. When the battery is
being charged the second lamp will illuminate orange and when this lamp
changes to green, the batteries are fully charged. Always ensure that the lamp
shows green before switching off and disconnecting the charger at the mains.
Connection Instructions
When you receive your vehicle the batteries are only partially charged –
always fully charge them before use, preferably over-night.
1. Place your machine in an area that is dry and well ventilated.
Make sure a power point is nearby.
2. Check the vehicle is switched off and the key removed.
19
Warning! When charging batteries NEVER smoke or charge batteries in a place where there are naked
flames such as gas-fired heaters as, under exceptional circumstances, batteries may give off gases that
could ignite and explode. If the scooter has been damaged, it is possible that the batteries have been
affected. In this case do not charge the scooter and refer to your dealer for assistance. Never charge the
scooter outside as the charger is not designed to get wet. If the charger appears damaged in
any way do not use it and contact your dealer for a replacement.
Warning! Always charge in a dry, well ventilated area.
Warning! It is strongly recommended that the mains socket used for charging the scooter is protected
by a 30 m/A RCD (residual current device). Many buildings have sockets protected by a system based
RCD. If you are in doubt as to the level of protection in your charging location then either purchase a plug in
RCD or consult a qualified electrician to verify that your charging location mains sockets are protected.
Warning! If batteries are damaged or frozen they could heat up during charging and in an extreme case,
explode.
Warning! Do not attempt to open the battery box/enclosure, there are no user serviceable parts inside. It
may be necessary for some carriers such as airlines to physically disconnect the batteries for transit. If this
is the case the battery cover can be removed without the use of tools once the seat has been removed.
This should only be done by appropriately skilled/qualified personnel.
Warning! Never use a different battery charger to that supplied by your dealer. Damage or injury may
occur if you do!
Warning! When charging batteries NEVER connect or disconnect the charger from the scooter while it is
still connected to the mains. - Remove the charger mains plug from the wall socket having first switched
the mains socket off if a switch is provided.
20
21

20 Rascal Vantage and Vantage X Scooters Owner's Manual and Service Record
3. Check the mains switch is off. Never connect or disconnect the charger from the scooter with the mains on.
4. Connect the charger to the charging point on the tiller of the scooter as above.
5. Connect the mains plug and switch on.
6. The first lamp illuminates green when the charger is powered up, then the second LED/lamp
illuminates orange during charging and then changes to green when the batteries are fully charged.
7. Switch off the mains and remove the plug from the battery when fully charged. Do not leave the
charger plugged in with the power off. This will gradually discharge your batteries.
The batteries are the lifeblood of your vehicle. Their characteristics can change depending on charging,
temperature, usage and other factors. Listed below are guidelines to prolong battery life.
1. After using your vehicle always charge it at the end of the day even after a short journey.
2. If you do not use your vehicle for a prolonged period, place it on charge once a week, overnight.
3. Always use the correct charger as supplied with your scooter.
4. If the batteries have been flat for a long time (about 2 months) it is recommended you contact your
dealer before charging.
5. Do not charge the vehicle in the open / out of doors – it may rain and the battery charger is not
waterproof.
6. Keep the vehicle in a well-ventilated area and away from any naked flame.
7. Do not part charge the batteries. Allow the charger to complete its cycle.
Note: Avoid storing your scooter in cold/damp places. This will shorten battery life and may cause
deterioration in their structure. Batteries are expensive to replace – it is wise to look after them.
Warning! Never disconnect a battery or the charger while the charger is connected to the mains
Warning! If one or both batteries are damaged they could heat up when charging and, in an extreme
case, explode.
Notice Your batteries are built-into the scooter and are not user-serviceable. Your dealer will replace them
when they are exhausted and dispose of them in line with environmental regulations applicable at the time.