Rational iVario Pro L User manual

iVario® Pro L
iVario® Pro XL
Original installation instructions

Device hand-over
Dealer: Installer:
Include the following information with queries:
Device type:
Device no.:
Your device was tested by (name):
2 / 60 80.06.243_iVario Pro L_XL_IM_V01_en-US

80.06.243_iVario Pro L_XL_IM_V01_en-US 3 / 60
Contents
1 Introduction ................................................................................................................. 5
1.1 Information on this manual ......................................................................................................5
1.2 Target audience............................................................................................................................5
1.3 Copyright.......................................................................................................................................6
1.4 Conformity ....................................................................................................................................6
1.5 Liability and warranty conditions ...........................................................................................6
1.6 Identification of the device.......................................................................................................7
2 Safety...........................................................................................................................10
2.1 Display of warning notices ....................................................................................................10
2.2 General safety information....................................................................................................10
2.3 Intended use...............................................................................................................................11
3 Product description .................................................................................................12
3.1 Device description....................................................................................................................12
3.2 Technical data ............................................................................................................................12
3.2.1 Device weight.................................................................................................................13
3.2.2 Device dimensions ........................................................................................................14
3.2.3 Pan dimensions ..............................................................................................................15
3.2.4 Thermal load....................................................................................................................16
4 Transport....................................................................................................................17
4.1 Lifting points on the device...................................................................................................18
4.2 Transport without pallet.........................................................................................................20
4.3 Transport with pallet ...............................................................................................................22
4.4 Transport without pallet with lift truck..............................................................................23
5 setting up....................................................................................................................24
5.1 Minimum distance to the device..........................................................................................24
5.1.1 Distance from walls.......................................................................................................24
5.1.2 Distance from heat sources ........................................................................................25
5.1.3 Distance from water sources .....................................................................................26
5.2 Setting up the device...............................................................................................................28
5.3 Device alignment......................................................................................................................28

4 / 60 80.06.243_iVario Pro L_XL_IM_V01_en-US
5.4 Aligning the device without electrical current .................................................................32
5.5 Fixing the device in place .......................................................................................................35
6 Electrical connection................................................................................................36
6.1 Regulations for the electrical connection ..........................................................................36
6.2 Opening the electrical compartment..................................................................................37
6.3 Connecting the device to the power grid..........................................................................40
6.4 Connect the device for demo mode to the power grid ................................................42
6.5 Closing the electrical compartment ....................................................................................42
6.6 Connected loads of different voltage types .....................................................................43
6.7 Checking the function of the socket in the device..........................................................44
6.8 Device options...........................................................................................................................45
7 Network connection ................................................................................................46
7.1 Notes on the network connection.......................................................................................46
7.2 Connecting the device to the network...............................................................................46
8 Water connection .....................................................................................................47
8.1 Regulations for water connection .......................................................................................47
8.2 Connecting the water inlet ....................................................................................................48
9 Wastewater connection..........................................................................................49
9.1 Regulations for the wastewater connection.....................................................................49
9.2 Connecting the wastewater drain .......................................................................................50
10 Decommissioning.....................................................................................................52
10.1 Notes on decommissioning...................................................................................................52
10.2 Disposal.......................................................................................................................................52
11 Options .......................................................................................................................53
11.1 Setup options.............................................................................................................................53

1 | Introduction
80.06.243_iVario Pro L_XL_IM_V01_en-US 5 / 60
1 Introduction
1.1 Information on this manual
This document is part of the device. Read this manual before carrying out the in-
stallation. The manual enables safe handling of the device and correct installa-
tion.
The images in this manual are examples only and may differ from the device.
This manual is valid for the following devices:
niVario Pro L
niVario Pro XL
Storage
Keep the installation manual and operating manual close to the device. During
service work, the installation manual must be accessible to specialist personnel
authorized by the manufacturer at all times.
Transfer
Pass this installation manual on to the owner of the device.
Explanation of symbols
aA requirement lists all conditions that must be met before an action.
1. An action step describes an action to be carried out by the reader.
>Shows a successful interim result.
2. Further action step.
>> The results shows the result of the action.
Explanation of the label on the device
Symbol for equipotential bonding in accordance with IEC 60417-5021
Symbol for hazardous voltage in accordance with IEC 60417-5036
1.2 Target audience
nThis document is aimed at trained technicians, who have been certified by
the manufacturer after taking part in trainings and safety trainings.
nThe installation, as well as inspection, maintenance and repair work, may
only be carried out by trained technicians.
nIt is advisable to only have inspection, maintenance and repair work carried
out by technicians authorized by the manufacturer.

1 | Introduction
6 / 60 80.06.243_iVario Pro L_XL_IM_V01_en-US
nThe device must not be used, cleaned or maintained by children. The de-
vice is not a toy. It must not be used as a toy even under supervision.
nThe device must not be used, cleaned or maintained by persons with lim-
ited physical, sensory or mental aptitude, or lack of experience or knowl-
edge, unless they are supervised by a person responsible for their safety
and have received instruction from this person in the risks associated with
the device.
nIn order to avoid the risk of accidents or damage to property, the manu-
facturer advises that technicians attend regular training and safety training
sessions.
1.3 Copyright
It is not permitted to pass on product-specific information to third parties. We
reserve the right to implement technical developments and changes in the in-
terest of progress. All rights are reserved, including those of translation and re-
production.
1.4 Conformity
The conformity applies to the complete device at the time of delivery. In the
event of upgrades, modifications and connection of additional functions, the
operator is responsible for obtaining an extended conformity.
nThe power connection is established and connected in accordance with
IEC 60335, taking into account EN 60335 and VDE 0700.
nThe water connection is established and connected in accordance with IEC
61770, taking into account EN 1717, DIN EN 13076 and DIN EN 13077.
nThe wastewater connection corresponds to the current valid SVGW/
SSIGE regulations and is tested and certified accordingly.
nThe device is tested and built in accordance with UL-197 and NSF 51.
nThe device is approved for use up to 4000 m above NHN in accordance
with IEC 60335.
The specified standards apply for Germany.
In all other countries, the relevant local and country-specific standards and
regulations regarding the installation and operation of industrial cooking appli-
ances must be observed.
1.5 Liability and warranty conditions
Liability
Installations and repairs that are not carried out by specialist personnel autho-
rized by the manufacturer or not using original service parts, as well as any
technical changes to the device that are not approved by the manufacturer, can
render the manufacturer’s product liability null and void.

1 | Introduction
80.06.243_iVario Pro L_XL_IM_V01_en-US 7 / 60
Warranty
The warranty does not cover damage caused by failure to observe this installa-
tion manual.
The following are also excluded from the warranty:
nDamage caused by incorrect use, installation, maintenance, repair
nUsing the device other than intended
nModifications or technical changes to the device that are not authorized by
the manufacturer
nFailure to use genuine service parts from the manufacturer
1.6 Identification of the device
Type plate
The type plate is located on the device base frame between the pan and electri-
cal compartment.

1 | Introduction
8 / 60 80.06.243_iVario Pro L_XL_IM_V01_en-US
The type plate includes the following information:
Model number
Connection voltage
Frequency
Connected load
Permissible flow pressure
range
Serial number
Marketing name
Device type and model number
The assignment can be found in the table below.
The device type designation and the model number on the type plate are dif-
ferent. Depending on the device option, the following digits are added to the
model number on the type plate.

1 | Introduction
80.06.243_iVario Pro L_XL_IM_V01_en-US 9 / 60
Device size type plate Device size
LMX.100CE … iVario Pro L
LMX.200CE … iVario Pro L with pressure option
LMX.100DE … iVario Pro XL
LMX.200DE … iVario Pro XL with pressure option

2 | Safety
10 / 60 80.06.243_iVario Pro L_XL_IM_V01_en-US
2 Safety
2.1 Display of warning notices
DANGER
Type and source of danger
Failure to observe these warnings will result in severe injuries or death.
Measures to avoid the danger
WARNING
Type and source of danger
Failure to observe these warnings could result in severe injuries or death.
Measures to avoid the danger
CAUTION
Type and source of danger
Failure to observe these warnings could result in minor or moderate
injuries.
Measures to avoid the danger
NOTE
Failure to observe these warnings could result in damage to property.
2.2 General safety information
The device is designed so that it does not pose a danger
when installed correctly. This manual describes proper instal-
lation of the device.
nObserve the relevant country-specific and local regula-
tions and standards in your country.
nUse lifting aids such as lifting straps when transporting.
nSecure the device against tipping when transporting and
after setup.
nWear suitable protective clothing, such as protective
gloves and safety shoes, during transport and installation.

2 | Safety
80.06.243_iVario Pro L_XL_IM_V01_en-US 11 / 60
nThe device should only be set up in a protected environ-
ment safe from frost and wind.
nDo not set up the device in adverse weather conditions,
such as rain.
nThe device should only be connected in accordance with
the installation manual and the information on the type
plate.
nSwitch off the device when disconnecting it from or con-
necting it to the power supply.
nAfter use, only transport the device in ambient temperature
of over 0°C [32°F].
nOnly store the device in ambient temperature of over 0°C
[32°F].
nDo not operate the device without an air filter.
nCheck the device for transport damage. Inform your spe-
cialist dealer/shipping company immediately if you sus-
pect transport damage.
2.3 Intended use
The device is designed for thermic food preparation. This device is only in-
tended for commercial use, such as in restaurant kitchens or catering operations
for schools, hospitals, or delis. Do not use this device outdoors. This device
must not be used for continuous mass industrial food production.
All other usages of this device are considered improper and dangerous. The
manufacturer accepts no liability for consequences arising from use other than
intended.

3 | Product description
12 / 60 80.06.243_iVario Pro L_XL_IM_V01_en-US
3 Product description
3.1 Device description
NOTE
Never seal or pipe the safety overflow
Do not reduce the cross-section of the safety overflow.
The safety overflow but be accessible and clear at all times. It is used for
ventilation and as a drain in the event of blockages.
11
33
44
55
66
1010
88
99
77
22
1 Safety overflow with sieve (no
connection)
6 Ethernet network connection
2 Wastewater connection 7 PG screw fittings for optional con-
nections
3 Hot water connection (optional) 8
4 Cold water connection 9
5 Power cable guide 10
3.2 Technical data
Protection class
The device corresponds to jet water connection class IPX5.
Ambient conditions for operation
nDo not set up the device in ambient temperatures below 5°C [41°F].

3 | Product description
80.06.243_iVario Pro L_XL_IM_V01_en-US 13 / 60
nDo not commission the device in ambient temperatures below 5°C [41°F].
nOnly set up the device in rooms with adequate ventilation via windows or
an extractor hood.
Sound emission value
The sound emission value is below 70 dB.
3.2.1 Device weight
Device with base
Device size Weight without packaging kg
[lbs]
Weight with packaging kg
[lbs]
iVario Pro L 232 [511] 271 [597]
iVario Pro L with
print option
247 [545] 288 [635]
iVario Pro XL 289 [637] 351 [774]
iVario Pro XL with
print option
304 [670] 351 [774]
Device with base and height adjustment
Device size Weight without packaging kg
[lbs]
Weight with packaging kg
[lbs]
iVario Pro L 272 [600] 313 [690]
iVario Pro L with
print option
287 [633] 328 [723]
iVario Pro XL 329 [725] 376 [829]
iVario Pro XL with
print option
344 [758] 391 [862]
Device without base
Device size Weight without packaging kg
[lbs]
Weight with packaging kg
[lbs]
iVario Pro L 213 [470] 257 [567]
iVario Pro L with
print option
228 [503] 269 [593]
iVario Pro XL 270 [595] 332 [732]
iVario Pro XL with
print option
285 [628] 332 [732]

3 | Product description
14 / 60 80.06.243_iVario Pro L_XL_IM_V01_en-US
3.2.2 Device dimensions
Device with base
z
x y
Device size L
Width mm [inch] x Depth mm [inch] y Height mm [inch] z
1031 [40 4/8] 894 [35 2/8] 1078 [42 4/8]
Device size XL
Width mm [inch] x Depth mm [inch] y Height mm [inch] z
1365 [53 5/8] 894 [35 2/8] 1078 [42 4/8]
Device without base
xy
z
Device size L
Width mm [inch] x Depth mm [inch] y Height mm [inch] z
1031 [40 5/8] 894 [35 2/8] 608 [23 7/8]
Device size XL
Width mm [inch] x Depth mm [inch] y Height mm [inch] z
1365 [53 6/8] 894 [35 2/8] 608 [23 7/8]

3 | Product description
80.06.243_iVario Pro L_XL_IM_V01_en-US 15 / 60
Packaging dimensions
Device with base Device size L
Width mm [inch] x Depth mm [inch] y Height mm [inch] z
1250 [49 2/8] 1100 [43 2/8] 1823 [71 6/8]
Device with base Device size XL
Width mm [inch] x Depth mm [inch] y Height mm [inch] z
1500 [59] 1100 [43 2/8] 1823 [71 6/8]
Device without base Device size L
Width mm [inch] x Depth mm [inch] y Height mm [inch] z
1250 [49 2/8] 1100 [43 2/8] 932 [36 6/8]
Device without base Device size XL
Width mm [inch] x Depth mm [inch] y Height mm [inch] z
15080 [62 2/8] 1100 [43 2/8] 932 [36 6/8]
3.2.3 Pan dimensions
Usable capacity
Device size Useful volume l [gal]
L 100 [26]
XL 150 [40]

3 | Product description
16 / 60 80.06.243_iVario Pro L_XL_IM_V01_en-US
Pan internal dimensions
y
x
z
Width mm [inch] x Depth mm [inch] y Height mm [inch] z
L 692 [27 2/8] 570 [22 4/8] 280 [11]
XL 1026 [40 3/8]
3.2.4 Thermal load
Device size Thermal load latent(kJ/h) Thermal load sensi-
tive(kJ/h)
iVario Pro L 26827 5540
iVario Pro XL 37343 8413
We reserve the right to implement technical developments and changes.

4 | Transport
80.06.243_iVario Pro L_XL_IM_V01_en-US 17 / 60
4 Transport
CAUTION
Risk of crushing due to the weight of the device
Hands, fingers and feet may be crushed.
nWear suitable protective clothing during transport.
nUse lifting aids such as lifting straps.
CAUTION
Risk of tipping during transport
Risk of crushing if the device tips over onto a person.
nNote the center of mass of the device.
nEnsure that the device does not tip over during transport or lifting.
CAUTION
Inclined plane during transport using transport aid
Risk of crushing and injury during transport using a transport aid over an
incline or uneven floor.
nDo not run over an incline of more than 10°.
nTake care when transporting the device.
NOTE
Damage to the device due to narrow areas
Note the width and height of the accesses during transport.
Only transport the device with the device cover closed.
NOTE
Incorrect transport
Do not push the device to the designated installation site.
The device feet may be damaged.
Transport the device correctly as outlined in this manual.
aThe device is on the transport pallet.
aThe device feet are positioned in the foot guides in the transport pallet box.
aThe designated installation surface is horizontal.
aThe device cover is closed.

4 | Transport
18 / 60 80.06.243_iVario Pro L_XL_IM_V01_en-US
aAt least 2 people are required for the transport.
1. Remove the packaging material.
4.1 Lifting points on the device
NOTE
Damage due to lifting incorrectly
Only lift the device via the designated lifting points.
Do not lift the device on the side wall of the electrical compartment.
Center of mass
The following graphic shows the center of mass of the device. The dimensions
for the center of mass shown are approximate for orientation.
CAUTION
Risk of crushing and injury if the center of mass is not observed
Failure to observe the center of mass can result in the device tipping over
during lifting and transportation.
nEnsure that the weight of the device is distributed evenly.
nNote the center of mass of the device.
x
x
z
y
y
z

4 | Transport
80.06.243_iVario Pro L_XL_IM_V01_en-US 19 / 60
Width mm [inch] x Depth mm [inch] y Height mm [inch] z
iVario Pro L 490 [19 19/64] 406 [16] 685 [26 31/32]
iVario Pro L With-
out base
484 [19 1/16] 410 [16 9/64] 275 [10 53/64]
iVario Pro XL 640 [25 13/64] 400 [15 3/4] 690 [27 11/64]
iVario Pro XL With-
out base
635 [25] 405 [15 15/16] 275 [10 53/64]
Lifting points on the device
1. Lift the device on the base frame marked in the figure and on the marked
pan paneling.
Device with base

4 | Transport
20 / 60 80.06.243_iVario Pro L_XL_IM_V01_en-US
Device without base
4.2 Transport without pallet
NOTE
Incorrect transport
Do not push the device to the designated installation site.
The device feet may be damaged.
Transport the device correctly as outlined in this manual.
NOTE
Damage due to lifting incorrectly
Only lift the device via the designated lifting points.
Do not lift the device on the side wall of the electrical compartment.
The manufacturer recommends transporting the device with cross straps.
aThe packaging material is removed.
aThe cross straps are on hand.