Raymarine St290 User manual

Document number: 86073-1
Use with: 81183-1
Date: 1 August 2002
ST290 Data Display - quick reference guide
User setup
FAVORITES
Number of Favorite pages
Link top and bottom?
Set top page 1
Set bottom page 1
Set top page 2
Set bottom page 2
Set top page 3
Set bottom page 3
Set top page 4
Set bottom page 4
Set top page 5
Set bottom page 5
UNITS
Set speed units
Set distance units
Set depth units
Set wind speed units
Set temperature units
Set volume units
Set flow rate units
LAMPS
Allocate instrument to group
Select adjustment type
Set lighting level 1
Set lighting level 2
Set lighting level 3
Select Magnetic or True
Set Chapter titles on or off
Set page first displayed
when chapter selected,
(top or last viewed)
Set race timer 1
Set race timer 2
Set race timer 3
Set speed data resolution
Set depth data resolution
Set wind speed resolution
OPTIONS
Set distance data resolution
Set local time offset
Set remote group
Set remote sequence
Set linked keypads
Set button beep on or off
RESPONSE
Speed
Depth
Heading
Wind angle
Wind speed
XTE
Display update
Normal
operation
USER SETUP chapter
2 sec
User Setup mode
USER (setup entry screen)
EXIT SETUP
If CUSTOM is selected:
use the button to move
to each page in turn, and at
each page, use the or
button to turn the page
either on if you want to see
it during normal operation,
or off if you do not want to
see it.
Select either FULL, SAIL,
POWER or CUSTOM
PROFILE
2 sec
ST290 Data Display - quick reference guide
Operation
Normal operation button actions
Chapter Select mode
Increase brightness
Decrease brightness
Press Select
chapter
Hold down
1 second Select
chapter
Lamp Adjust mode
Set upper display as active display area.
Set lower display as active display area.
Increase parameter value
Decrease parameter value
Edit mode
Press
Hold down for 1 second
Select pages in current chapter
Select pages in current chapter
Press
Press
Increase contrast
Decrease contrast
Contrast Adjust mode
Hold down for 1 second
Hold down
for 1 second
1 secondHold down
Setting an alarm: Press to set alarm
threshold, or switch alarm off.
Controlling a timer: Press to switch
timer on/off or start/stop timer.

Beaufort
True wind speed
Longitude
Course over ground (COG)
Waypoint name
Bearing to waypoint (BTW)
Estimated time of arrival (ETA)
Time to go (TTG)
Local time
Local date
Race start timer 3
Race start timer 2
Race start timer 1
TIMERS
Alarm clock
Stop watch
Countdown timer
Tide drift
To select the chapter you want
Press 1 second
hold down
Current depth
Minimum depth
Maximum depth
Offset
DEPTH
Locked heading
Heading on next tack
Course Over Ground (COG)
Compass bearing
HEADING
SPEED
Boat speed
Average speed
Maximum speed
Total log
Trip log
VMG to windward
VMG to waypoint
USER SETUP
FAVORITES
Battery voltage
VESSEL
Rudder angle
HDOP
Satellites tracked
Fix
GPS
D5679-2
WIND
Head/lift
True magnetic wind direction
Relative true wind angle
Relative apparent wind angle
NAVIGATE
Latitude
Speed over ground (SOG)
Distance made good (DMG)
Distance to waypoint (DTW)
Cross track error (XTE) plus
steer bar
Status
PILOT
Engine hours
RPM
Fuel rate
Coolant level
ENGINE N
Fuel level
Turbo oil temperature
Engine temperature
Exhaust gas temperature
Battery voltage
Boost pressure
ENVIRONMENT
Sea temperature
Tide set
Sunrise time
Favorite page 5
Favorite page 4
Favorite page 3
Favorite page 2
Favorite page 1
Set rollover on/off & delay
Apparent wind speed
Course made good (CMG)
Twilight pm
Twilight am
Sunset time
Press
for 2 seconds,
to enter User Setup
Deep water
Shallow anchor
Apparent wind speed (AWS) low
Off course
True wind angle (TWA) high
Boat speed high
Boat speed low
ALARMS
Sea temperature high
Sea temperature low
Shallow water
Apparent wind angle (AWA) high
Apparent wind speed (AWS) high
True wind speed (TWS) low
Deep anchor
Apparent wind angle (AWA) low
True wind speed (TWS) high
True wind angle (TWA) low
Waypoint arrival
Notes:
1. N = engine number
2. A separate ENGINE chapter
is provided for each engine.
Data Display Full Profile
Note:
This illustration shows the chapter and page structure of an ST290 Data display Full Profile.
If you use a different profile, the chapter and page structure may be different.
Note: PILOT chapter available
only if a Raymarine autopilot
system is connected to ST290

Document number: 86073-1
Use with: 81183-1
Date: 1 August 2002
ST290 Data Display - quick reference guide
User setup
FAVORITES
Number of Favorite pages
Link top and bottom?
Set top page 1
Set bottom page 1
Set top page 2
Set bottom page 2
Set top page 3
Set bottom page 3
Set top page 4
Set bottom page 4
Set top page 5
Set bottom page 5
UNITS
Set speed units
Set distance units
Set depth units
Set wind speed units
Set temperature units
Set volume units
Set flow rate units
LAMPS
Allocate instrument to group
Select adjustment type
Set lighting level 1
Set lighting level 2
Set lighting level 3
Select Magnetic or True
Set Chapter titles on or off
Set page first displayed
when chapter selected,
(top or last viewed)
Set race timer 1
Set race timer 2
Set race timer 3
Set speed data resolution
Set depth data resolution
Set wind speed resolution
OPTIONS
Set distance data resolution
Set local time offset
Set remote group
Set remote sequence
Set linked keypads
Set button beep on or off
RESPONSE
Speed
Depth
Heading
Wind angle
Wind speed
XTE
Display update
Normal
operation
USER SETUP chapter
2 sec
User Setup mode
USER (setup entry screen)
EXIT SETUP
If CUSTOM is selected:
use the button to move
to each page in turn, and at
each page, use the or
button to turn the page
either on if you want to see
it during normal operation,
or off if you do not want to
see it.
Select either FULL, SAIL,
POWER or CUSTOM
PROFILE
2 sec
ST290 Data Display - quick reference guide
Operation
Normal operation button actions
Chapter Select mode
Increase brightness
Decrease brightness
Press Select
chapter
Hold down
1 second Select
chapter
Lamp Adjust mode
Set upper display as active display area.
Set lower display as active display area.
Increase parameter value
Decrease parameter value
Edit mode
Press
Hold down for 1 second
Select pages in current chapter
Select pages in current chapter
Press
Press
Increase contrast
Decrease contrast
Contrast Adjust mode
Hold down for 1 second
Hold down
for 1 second
1 secondHold down
Setting an alarm: Press to set alarm
threshold, or switch alarm off.
Controlling a timer: Press to switch
timer on/off or start/stop timer.