Raytec RL F 25 User manual

Installation Steps
1. Mount Illuminator
2. Connect Illuminator to low voltage
power supply
3. Input 12-24V DC/ 24V AC
Optional Set-up (if required)
4. Adjust Power to alter light intensity
5. Adjust Photocell sensitivity
6. Photocell following contact
RM/RL F 100 Setup
7. Telemetry input and photocell
following contact
Set Up Steps
1. Position illuminator adjacent to
camera and point towards scene
2. Adjust vertical and horizontal
position of lamp to ensure full field
of view illuminated
3. Tighten all fixings
Package Contents
1. Illuminator including mounting
bracket
(RM/RL F 100 only, includes
additional wiring loom)
illuminators installation guide
RAYMAX / RAYLUX
FUSION illuminator
Overview
This installation guide provides instructions for installing the RAYMAX
and RAYLUX FUSION series illuminators
FUSION
GOLDEN RULES:
• Ensureoperatingvoltageis
correct for unit being installed
(12-24V DC/ 24V AC)
www.rayteccctv.com
Version: 2

Specifications subject to change without notice. Installation
to be carried out by suitable trained and qualified personnel.
!
Install in a well
ventilated area
Do not continually
stare at lamp
2
LED illuminator
Bracket
RM/RL F 25 & 50
PhotocellPower
adjust
Photocell
adjust
12/24V
AC/DC
input
Power
in
Made in UK
P-cell
adjust
-
+
Power
adjust
-
+
RM/RL F 100
Telemetry Input &
Photocell following contact
Power
adjust
-
+
Power
in
Made in UK
P-cell
adjust
-
+
Telemetry
P/C Contact
Back of Unit
‘Command and Control’ Technology™
DC AC
Black wire - ~
Red wire + ~
DC AC
Black wire - ~
Red wire + ~
RM/RL F 25 & 50
Cables
1x four core cable
Orange and Brown wires=
Photocell following contact.
Volt free output. Non polarity sensitive.
+ Photocell following contact
RM/RL F 100
1x four core cable loom
RM/RL F 100 is supplied with additional cable loom
White & Brown wires = Photocell following contact.
Volt free output. Non polarity sensitive.
Blue & Black wires = Telemetry connection.
Requires volt free input.
1.5m

Installation
3
Mount illuminator
Connect Illuminator to low voltage power
supply: Installers can extend or reduce lead
length using appropriate cable and weather
proof box
Input 12-24V DC/ 24V AC
2
3
1
RM/RL F 100 only:
Telemetry input and photocell following
contact. Remove cap on telemetry and
photocell following contact connector.
Connect additional cable loom (see below).
5
7
6
4
1
2
Adjust Photocell sensitivity. Remove the cover
and turn the ‘photocell adjust’ to alter photocell
sensitivity to ambient lighting condition.
Photocell following contact, volt free relay
contact - normally open (day) to normally
closed (night).
Clockwise=more sensitive
Anticlockwise=less sensitive
RM/RL F 25 & 50 only
Orange and brown wires =
Photocell following contact
RM/RL F 100 only
Blue and black wires =
telemetry connection for remote operation
White and brown wires =
photocell following contact connection
Adjust Power to alter light intensity.
Remove the cover and turn the ‘power adjust’
to alter the intensity of the light level.
Clockwise=increase
Anticlockwise=decrease
Note: Red =positive
Black = negative
Power
in
Made in UK
P-cell
adjust
-
+
Power
adjust
-
+
Power
adjust
-
+
Power
in
Made in UK
P-cell
adjust
-
+
Telemetry P/C
Contact
Optional Set-up (if required)
Note: Factory set to max. power
RM/RL F 25 & 50
RM/RL F 100 only

Set Up
Camera
Light
Light
x x Light
Camera
Match illumination to camera field of view
Position illuminator adjacent to
camera and point towards scene
(Optional night set-up for
optimum image performance)
4
Reduces performance May cause hot spots Best performance
Camera
1Adjust vertical and horizontal
position of lamp to ensure full field
of view illuminated
2
Tighten all fixings
3
TARGET

5
Technical Drawings (Not to scale)
Standard Bracketry
Optional Bracketry
25mm
(1”)
12.5mm
(0.5”)
47mm
(1.9”)
RM/RL F 25
25mm
(1”)
36mm
(1.4”)
72mm
(2.8”)
RM/RL F 50
25mm
(1”)
52mm
(2”)
104.5mm
(4.1”)
RM/RL F 100
Wall Mount Dome MountPtz Mount Pole Mount

6
FUSION Specifications
RM FUSION 100 RM FUSION 50 RM FUSION 25
Max. Distance
Model dependent 150m 40m 20m
Consumption
~35W max 25W max 12W max
Input 12-24V DC/ 24V AC 12-24V DC/ 24V AC 12-24V DC/ 24V AC
Current 2.6A @ 12V
or 1.3A @ 24V
1.5A @ 12V
or 0.75A @ 24V
1A @ 12V
or 0.5A @ 24V
Weight 1.4kg 1.0kg 0.5kg
Environment IP66 IP66 IP66
Dimensions
L x W x D
180 x 135 x 65 mm
(7 x 5.3 x 2.5”)
135 x 100 x 63 mm
(5.3 x 4 x 2.5”)
75 x 100 x 54mm
(3 x 4 x 2”)
RL FUSION 100 RL FUSION 50 RL FUSION 25
Max. Distance
Model dependent 100m 35m 17m
Consumption
~35W max 25W max 12W max
Input 12-24V DC/ 24V AC 12-24V DC/ 24V AC 12-24V DC/ 24V AC
Current 2.6A @ 12V
or 1.3A @ 24V
1.5A @ 12V
or 0.75A @ 24V
1A @ 12V
or 0.5A @ 24V
Weight 1.4kg 1.0kg 0.5kg
Environment IP66 IP66 IP66
Dimensions
L x W x D
180 x 135 x 65 mm
(7 x 5.3 x 2.5”)
135 x 100 x 63 mm
(5.3 x 4 x 2.5”)
75 x 100 x 54mm
(3 x 4 x 2”)
INFRA-RED Series
WHITE-LIGHT Series
Integrated Command and Control™ Technology
RM/RL F 25/50
•Inbuiltphotocellforautomaticon/off
operation
•Inbuiltpoweradjust
•Inbuiltphotocellleveladjust
•Photocellfollowingcontact 
RM/RL F 100
•Inbuiltphotocellforautomaticon/off
operation
•Inbuiltpoweradjust
•Inbuiltphotocellleveladjust
•Photocellfollowingcontact
•Telemetryinputforremoteoperation

7
Trouble Shooting
Ensure all tests are undertaken by a qualified, trained engineer.
Ensure safe working practices are followed at all times.
Step 1: Basics
• CheckpolarityofLampconnection
red=+ve, black=-ve
• Ensurepoweris12-24VDC/24VAC
• Checkphotocellisworking-coverphotocell,lightshouldturnon.
• Ensurepowersupplyissuitablyratedtoproduct-checkpage6for
specifications
If OK…
Step 2: Lamp Test
• Checkcurrentdrawoflampcorrespondstospecicationonpage6
• Checkcurrentoflamp–seeinstructionsforcorrectcurrentsetting
To check lamp current remove +ve (red) lead from power supply and connect
multimeter (set to 10A) in line with the lamp. [One lead of multimeter in common
(COM), other lead into 10A socket of multimeter; set multimeter to read Amps].
Refer to PSU Specifications for correct current settings, see page 6.
Step 3: Set-up Camera, lens and illumination
• Checkalignmentoflamp
• Checkcameralens–fullyopenatnight&setcorrectly
• CheckmodelnumbertoRaytecperformancespecicationtoensurerequired
distance is achievable
Step 4: Call Raytec for further assistance
Note down:
•Modelandserialnumberofilluminator
•Cameramakeandmodel
•Lensmakeandmodel
If the Raytec lamp is still not delivering the required performance, please contact
us for further assistance.

UK / Europe
T: [phone]
F: [phone]
[e-mail]
Americas (Toll Free)
T: [phone]
[e-mail]
www.rayteccctv.com