real living GBO23-901C4 User manual

ROCKBRIDGE ALL WEATHER WICKER 4PK DINING CHAIR WITH
SEAT CUSHION AND LUMBAR PILLOW
ASSEMBLY INSTRUCTIONS
ITEM# : GBO23-901C4
SKU# : 810580329
Need help? We are here for you! 1-888-733-8169 Toll Free
Or email us at [email protected],[e-mail]
[email protected]

GENERAL BEST PRACTICES FOR ASSEMBLY:
Read all instructions before starting
Clear a flat covered space to begin assembly
Always best to do it with a friend
Note that hardware required is provided for every step
Pay attention to orientation
Number of the hardware corresponds to its letter in the package
Helpful hints provided along the way
WARNINGS:
Use the correct screws as indicated. All screws should be hand tightened until the complete piece is
assembled ( This will make the assembly process much easier ). Once the piece is fully assembled, then go
back and tighten all screws with provided tool.
Keep all children and pets away from assembly area. Children and pets should be supervised when they are in the area of the
product construction.
Keep assembly area at least 6 feet from any obstruction such as a fence, garage, house, overhanging branches, laundry line or
electrical wires.
Some parts may contain sharp edges. When assembling and using this product, basic safety precautions should always be followed
to reduce the risk of personal injury and damage to the product. Please read all instructions before assembly and use.
The chairs are not to be used for standing purposes and will not function as a stool or step-ladder. Use on even surfaces only.
The chair is used at weight of 250lb (113kg). Improper use of this product or failure to use as directed may
result in injury. Not intended for commercial use.
MAINTENANCE
STAIN RESISTANT CUSHIONS CARE —— KEEP THE CUSHIONS IN STORAGE ON RAINY DAYS.
SPILLS: Immediately wipe up the spill using a white damp cloth. Repeat process if necessary until stain is gone.
Allow cushions to air dry.
FABRIC CARE: Hand wash cold, non-chlorine bleach when needed, lay flat to dry. Cool iron if necessary. Do not dry clean.
ALL WEATHER WICKER PRODUCT CARE
Before using, clean the product completely with a soft dry towel. When not in use, wipe free of any dirt or loose objects, wash with a
mild solution of soap and water, rinse thoroughly and dry completely. Do not use strong detergent or abrasive cleaners. Screws can
loosen over a period of usage, please check the screws occasionally and re-tighten if necessary.

PARTS LIST FOR 1 CHAIR
A1
A2
B
1PC Left Arm 1PC Right Arm 1PC Chair back
C
J
K
1PC Seat Panel 1PC Seat Cushion 1PC Lumbar Pillow
HARDWARE LIST FOR 1 CHAIR
D
E
F
2PC Big Washer 4PC Screw(φ8x35mm) 4PC Screw(φ6x35mm)
G
H
I
1PC Allen Wrench 4PC Spring Washer 4PC Small Washer

STEP 1
Secure chair back (B) to left arm (A1) with 1 screw
(E) by using allen wrench (G). Do not fully tighten
screws now.
STEP 2
Secure right arm (A2) to the other side of assembled
chair back (B) with 1 screw (E) by using allen wrench
(G). Do not fully tighten screws now.
A1
B
A2
A1
B
E
G
E
G

STEP 3
Secure seat panel (C) to assembled chair arms (A1.
A2) with 4 screws (F), 4 small washers (I) and 4
spring washers (H) by using allen wrech (G). Do not
fully tighten screws now.
STEP 4
Secure seat panel (C) to assembled chair back (B)
with 2 big washers (D) and 2 screws (E) by using
allen wrench (G). Verify the alignment and adjust,
then fully tighten all the screws.
C
A1
A2
C
E
G
D
F
G
H
I

STEP 5
Put seat cushion (J) and lumbar pillow (K) on the
chair. The chair is assembled.
Warranty
One year limited warranty.
Proof of purchase (dated register receipt) is required for warranty claims.
It remains the customer's responsibility for freight and packing charges to and from the service center.
K
J