real living CT006A User manual

Read all instructions before starting
Clear a flat covered space to assemble
We recommend two people for assembly
Note that hardware required is provided for every step
Pay attention to orientation
Letter of the part corresponds to a sticker on the product
Number of the hardware corresponds to its number in the package
Helpful hints provided along the way
Regularly check hardware and tighten if necessary
GENERAL BEST PRACTICES FOR ASSEMBLY:
MAINTENANCE:
CARE AND CLEANING:
Clean periodically by wiping the product with a soft clean cloth
DO NOT use abrasive chemicals for cleaning

LEFT LEG RIGHT LEG
B
FRONT SUPPORT BAR
C
D
BACK BOTTOM SUPPORT BAR
E
BOTTOM PANEL
G
TOP PANEL
H
RIGHT SIDE PANEL
K
BACK PANEL
J
LEFT SIDE PANEL
I
MIDDLE PANEL
L
LEFT SIDE PANEL OF DRAWER
M
BACK PANEL OF DRAWER
N
REAR SUPPORT BAR
F
A
O
PARTS LIST
MIDDLE PANEL

Q
RIGHT SIDE PANEL OF DRAWER
P
CAM CAM LOCK PHILLIPS SCREW
WOOD DOWEL ALLEN WRENCH
13
67
5
2
PARTS LIST
ALLEN BOLT
4
HARDWARE LIST
PHILLIPS SCREW
NOT INCLUDED
DRAWER FRONT PANEL
R
PHILLIPS SCREW
8

Assembled View
STEP 1
15
G
1
1
1
1
1 1
1
5
5
5
5
5
5
Insert cam (1) into top panel (G) using a Phillips screwdriver (not
provided) and full tighten. Insert Wood dowel (5) into top panel
(G) .

Assembled View
STEP 2
5
2
2
J
I
K
Insert cam (1) and wood dowel (5) into right side panel (K) and
left side panel (I) as shown. Align the cams and dowels with the
holes in the ends of back panel (J) and slide into place. Secure
the panels together with cam lock (2). Fully tighten cams using
Phillips screwdriver (not provided).
1
2
5
1
1
5

Assembled View
STEP 3
2
2
2
2
2
2
G
K
I
J
Insert cam lock (2) into holes of left side panel (I), right side panel
(K) and back panel (J). Align the holes in the assembled side and
back panels with the cams and wood dowels in top (G) and
lower into place. Tighten cam locks (2) with Phillips screwdriver
(not provided) to secure the panels together.

STEP 4
15
Insert cam (1) into top panel (G) using Phillips screwdriver (not
provided) and fully tighten. Then insert wood dowel (5) into top
panel (G).
1
5
5
1
G
Assembled View
G

STEP 5
2
Insert cam lock (2) into holes of middle panel (L) & (M). Align the
holes in middle panel (L) and middle panel (M) with the cams and
dowels in top panel (G) and slide into place as shown. Secure the
panels together by tightening the cam locks (2) with Phillips
screwdriver (not provided).
Assembled View
G
G
M
L
2
2
2
2

STEP 6
3
Attach back panel (J), middle panel (L) and (M) with Phillips screw (3)
using Phillips screwdriver (not provided).
3
J
L
M

Assembled View
STEP 7
7
4
4
7
Assemble front support bar (D), back support bar (C) and back bottom
support bar (E) to left leg (A) and right leg (B) with Allen bolts (4) using
Allen wrench (7).
4
4
E
D
C
B
A4
4
4
4
Three holes are on
the same side.
Make sure the
holes along
the top of
cross bars are
towards the
inside of
frame.
INSIDE
INSIDE
C
D

Assembled View
STEP 8
6
Attach rear support bar (F) to assembled frame with Phillips screw (8) using
Phillips screwdriver (not provided).
6
F
6
6

STEP 9
Carefully place the assembled metal frame onto the bottom of the
assembled drawer box as shown. Secure the assembled frame to the
drawer box with Phillips screw (8) using Phillips screwdriver (not provided).
Assembled View
8
8
8
88
8
8

STEP 10
Attach bottom panel (H) to metal frame with Phillips screw (6) with
Phillips screwdriver (not provided).
Assembled View
6
6
6
6
6
6
6
6
66
66
6
H

Assembled View
3
3
3
OP
N
OP
N
STEP 11
Attach right side panel of drawer (P) and left side panel of drawer (N) to
back panel of drawer (O) with Phillips screws (3) using Phillips screwdriver
(not provided).

STEP 12
12
Slide bottom panel of drawer (Q) into the grooves of side panels of drawer
until it is fully inserted into back panel of drawer. Insert cams (1) into front
panel of drawer (R) and fully tighten using Phillips screwdriver (not
provided). Align the cams in front panel of drawer with the holes of side
panel of drawer and slide into place. Secure the panels together with cam
locks (2). Fully tighten cam locks.
1
1
2
2
Q
R
Assembled View
Repeat step 11~ step 12
for another drawer

STEP 13
PLEASE NOTE: The drawers should slide
completely into desk. If drawers jam or bind,
remove them, realign the glides and reinsert.
Assembly is now complete.
Align the glides on the drawer with
the glides in the drawer box and
insert with equal pressure on both
sides.