RealFlame HEATSEEKER 700 Installation instructions

INSPIRE FLAME EFFECT SPACE HEATER
MODELS 700/900/1100
INSTALLATION &OPERATING MANUAL
The Inspire space heater is suitable to be installed into a frame out installation.
Designed to operate on Natural gas and LPG gas. Approval no.GMK 10528
Version 10A

1 | P a g e
WARRANTY INFORMATION
The benefits provided to you under the following warranty are in addition to any other rights and remedies available to you under the
law.
1. Warranty
If:
(a) During the first 15 years from the date of purchase (Firebox Warranty Period), there is a defect in the firebox of the Gas Burner;
or
(b) During the first 2 years from the date of purchase (Parts Warranty Period), there is a defect in the gas valves or other parts of the
Gas Burner, due to improper workmanship or material, Glen Dimplex will replace or repair the Gas Burner without charge. Any
replacement product is warranted only for the time remaining on the original Firebox Warranty Period or the Parts Warranty Period
as relevant.
2. Registration
You must register to receive the benefit of this warranty by completing the warranty registration on our website
(www.realflame.com.au) or completing and mailing the attached registration card within 30 days of purchase of your Gas Burner (or,
if the Gas Burner is fitted to a new home, within 30 days of the date of settlement of purchase of such new home).
3. Exclusions
Glen Dimplex is not obliged to replace or repair the Gas Burner under clause 1 if:
(a) It has been improperly stored, installed, connected, used, operated or repaired, or damaged, abused, tampered with, altered
(without our written approval), or not maintained in strict accordance with our installation and operating instructions; or
(b) It has been installed in an outdoor setting.
4. Limit of Liability
The warranty provided under this warranty is limited to replacement or repair of the Gas Burner only, at our option. To the extent
permitted by law, Glen Dimplex excludes liability for consequential loss or any other loss or damage caused to property or persons
arising from any cause whatsoever, and damage arising from normal wear and tear.
5. Claiming under the Warranty
In order to claim under this warranty, you must, within the Firebox Warranty Period or the Parts Warranty Period (as relevant), contact
Glen Dimplex, providing the original proof of purchase and the details below:
Supplier Name ________________________
Date of Purchase / settlement of property if new home ______________________
Model / Serial Number _______________________
This warranty does not cover the cost of claiming under the warranty or transporting the Real Flame Gas Burner to and from the supplier
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or
refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have
the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
If you would like to speak to someone about your Gas Burner or claiming under this warranty, please contact the
Service Warranty Desk on 1300 554 155.
Glen Dimplex Australia Pty Ltd ACN 69 118 275 460
Head Office: 1340 Ferntree Gully Road, Scoresby 3179
Telephone: [phone] Facsimile: [phone]

2 | P a g e
WARNING
The Inspire space heater has a primary safety glass fitted in front of the glass door. This safety glass is fitted to
this appliance to reduce the risk of injury from burns and at no time should this glass be permanently removed.
For protection of young children or the infirm, a secondary guard is required.
The appliance is not intended for use by persons (including children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety. Children should be supervised to
ensure that they do not play with the appliance.
WARNING
The outer glass panel gets extremely hot! Precaution should be taken and young children supervised at all
times when heater is operating
INSTALLATION NOTICE
The installation of this appliance is only to be carried out by an authorized person in accordance with
the Manufacturer’s Instructions, local gas fitting regulations, AS/NZS5601.1-2013 installation code for
gas burning appliances and any other relevant statutory regulations.
Do not modify this appliance
In all cases the installation of this appliance shall meet the requirements as set out in AS/NZS5601.1-
2013.
Do not install in a fireplace as a Type 1 installation.
NOTE: A slight smell may be apparent for the first few hours of use. This is due to the heat resistant paint
curing. It is recommended to open windows in the room for the first lighting of the fire. In some instances, a
slight discolouration may occur inside the firebox. This is a normal condition and is not covered by warranty.
IMPORTANT SAFETY NOTICE
DO NOT PLACE ARTICLES ON OR AGAINST THIS APPLIANCE.
DO NOT USE OR STORE FLAMMABLE MATERIALS IN OR NEAR THIS APPLIANCE
DO NOT SPRAY AEROSOLS IN THE VICINITY OF THIS APPLIANCE WHILST IT IS IN OPERATION
CARE MUST BE TAKEN TO ENSURE THAT ANY RETURN AIR REGISTER OR EXHAUST SYSTEM DOES NOT
ADVERSLEY AFFECT THE OPERATION OF THE APPLIANCE OR DRAUGHT OF CHIMNEY OR FLUE.
APPLIANCE IS DESIGNED TO OPERATE WITH LUMINOUS FLAMES. MAY EXHIBIT SLIGHT CARBON
DEPOSIT
SERVICING
It is recommended you service your gas fire every 2 years as a minimum.
CORD REPLACEMENT
Electrical cord replacement must be undertaken by qualified and trained personnel only

3 | P a g e
Table of Contents
WARRANTY INFORMATION................................................................................................................................. 0
DATA PLATE ......................................................................................................................................................... 4
Inspire 700....................................................................................................................................................... 4
Inspire 900....................................................................................................................................................... 4
Inspire 1100..................................................................................................................................................... 4
DIMENSIONS........................................................................................................................................................ 4
Inspire 700....................................................................................................................................................... 5
Inspire 900....................................................................................................................................................... 5
Inspire 1100..................................................................................................................................................... 6
Power Flue....................................................................................................................................................... 6
LOCATION............................................................................................................................................................ 7
INSTALLATION CLEARANCES............................................................................................................................ 7
INSTALLATION CODES...................................................................................................................................... 7
FLUE CONFIGURATIONS .................................................................................................................................. 7
FLUE TERMINATION LOCATION........................................................................................................................... 8
SETUP WITH EXTERNAL WALL MOUNTED FAN TERMINAL ............................................................................... 10
ROOFTOP POWERFLUE TERMINATION ............................................................................................................. 14
Insulation requirements for flue runs ........................................................................................................... 14
TIMBER FRAME INSTALLATION ......................................................................................................................... 20
MEDIA INSTALLATION ....................................................................................................................................... 22
MEDIA TYPES ................................................................................................................................................. 22
COMMISSIONING PROCEDURE ......................................................................................................................... 36
OPERATION –USER INSTRUCTIONS .................................................................................................................. 36
APPLIANCE QUICK OPERATION ..................................................................................................................... 36
REMOTE CONTROL OPERATION.................................................................................................................... 37
TECHNICAL DATA........................................................................................................................................... 37
TROUBLESHOOTING .......................................................................................................................................... 42
WIRING DIAGRAM............................................................................................................................................. 44
AERATION ADJUSTMENTS and BURNER SIZES .................................................................................................. 45
CONVERSION DETAILS - Natural gas /LPG......................................................................................................... 46
INSPIRE 700 MODEL ...................................................................................................................................... 46
INSPIRE 900 MODEL ...................................................................................................................................... 47
INSPIRE 1100 MODEL .................................................................................................................................... 48
PARTS LIST ......................................................................................................................................................... 49

4 | P a g e
DATA PLATE (Affixed to the base of the unit for reference to gas pressure & consumption)
Inspire 700
GAS TYPE
INJECTOR SIZE
TPP
N.G.C. (MJ/hr)
Natural Gas
1 X 2.30mm
0.88kPa High
0.40kPaLow
22.0 High/16.0 Low
LPG
1 X 1.35mm
2.48kPa High
1.58kPaLow
22.0 High/17.0 Low
Inspire 900
GAS TYPE
INJECTOR SIZE
TPP
N.G.C. (MJ/hr)
Natural Gas
1 X 2.45mm
0.89kPa high
0.42kPa Low
24.0 High/16.0 Low
LPG
1 X 1.45mm
2.49kPa High
1.58kPaLow
24.0 High/19.0 Low
Inspire 1100
GAS TYPE
INJECTOR SIZE
TPP
N.G.C. (MJ/hr)
Natural Gas
1 X 2.65mm
0.88kPa High
0.41kPaLow
29.0 High/20.0 Low
LPG
1 X 1.50mm
2.45kPa High
1.51kPaLow
27.0 High/21.0 Low
Max - Min inlet pressure range
Natural gas: 1.13kPa - 5.00 kPa
LPG: 2.75kPa - 5.00 kPa
Note: Gas pressures are not adjustable on the Inspire models.
DIMENSIONS
Gas and electrical connection cut-out dimensions for all models

5 | P a g e
Inspire 700
Inspire 900

6 | P a g e
Inspire 1100
Power Flue

7 | P a g e
LOCATION
Select a location where the fire can be supervised during operation.
An electrical isolation switch must be fitted at the appliance or on an adjacent wall to allow for emergency
shutdown and maintenance.
Installation must meet Australian gas codes AS/NZS 5601.
INSTALLATION CLEARANCES –Clearances from combustible materials
Floor - 0mm Sides - 5mm Top - 5mm
Flue outer - 25mm Front - 250mm Back - 25mm
INSTALLATION CODES
Installers –Please ensure the installation and instruction manuals supplied with this appliance are supplied
to the customer and the customer is trained on how to operate the appliance correctly.
Do not modify the appliance.
Do not exceed maximum rated pressures.
Appliance must be installed as per gas installation code (AS/NZS 5601) and applicable electrical installation
code (AS3000).
Test for gas leaks prior to operating appliance. Check gas pressures and adjust if incorrect.
WARNING - Transit material such as cardboard packaging, pallet, plastic wrap, glass packaging warning
labels and burner media protection must be removed prior to use.
FLUE CONFIGURATIONS
1. Wall mount powerflue module: Flue configurations are a maximum of 5m, flue runs less than 5m are
permitted.
2. Rooftop powerflue termination: Flue configurations are a maximum of 8.5m, flue runs less than
8.5m are permitted. Refer Rooftop termination section for more details and installation instructions.
Aluminium flexible flue is used for both the inlet and outlet.
Flue runs 5m or 8.5m or less (75mm diameter Aluminium flexi flue)
Inlet pipe - Maximum flue run 5m or 8.5m total length including 5 x 90 bends
Outlet pipe - Maximum flue run 5m or 8.5m total length including 4 x 90 bends
Appliance is supplied with a 2 x 5m or 2 x 8.5m flexible flue lengths. Flue can be cut to length as
required.
Recommended bend radius 150mm or larger. Bends must not form a P Trap.

8 | P a g e
Flue must be clipped and supported support. Connections must be sealed with silicon and clamped
where advised.
Recommended Silicon –Non acetic, neutral cure 200degrees or higher temperature rated. Bostik
RTV 926 or similar.
U style flue runs must not be installed
FLUE TERMINATION LOCATION
•Flue terminations shall not be recessed in walls or sidings.
•EXTREMELY IMPORTANT: In heavy snow areas take extra care to prevent blocking flue
termination with snow removal equipment.
•Flue gases exiting flue terminals are very hot and must not be restricted to assure fireplace
combustion is not affected.
•Do not place, build any obstruction, plant any bushes or for any reason attempt to conceal
the flue termination. To do so will affect the operation of the fireplace and may be
hazardous
•This unit must always vent directly to outdoors.
GAS CONNECTION –15mm (1/2”) Compression union
ELECTRICAL CONNECTION –3 Pin 10 Amp GPO plug
POWER RATING OF APPLIANCE –230V 50Hz 0.8Amp

9 | P a g e
INSPIRE FLUE TERMINAL LOCATION

10 | P a g e
SETUP WITH EXTERNAL WALL MOUNTED FAN TERMINAL
Wall mounted fan module –
terminal must be installed with clearances as
specified by AS/NZS 5601.1 Clause 6.9.3
Run exhaust flue and air intake flue as required
Maximum run 5mts.Flues can be run next to each
other. Maintain the required clearances to
combustibles.
Connection to appliance
Cut tube to length where required.
Ensure ends are burr free and round, test fit flue will
slide over connection.

11 | P a g e
Recommended Silicon –Non-acetic, neutral cure
150degc or higher temperature rated. Bostik RTV
926 or similar.
Apply an 8mm thick silicon bead fully around
heater connection approx. 10mm from the top.
Apply an 8mm thick silicon bead fully around the
lower fan connection spigot approx. 10mm from
the end.
Apply an 8mm silicon bead fully around the inside
of the flue end (heater connection end)
Fit flue clamp over flue (loosely).
Slide flue onto connection spigot fully. Tighten
clamp fully. Wipe excess silicon, visually check
connection to ensure connection is fully sealed.
Repeat above with air intake flue pipe to heater
connection.
Clip flues as required to provide adequate
support.
Connection to wall mounted fan terminal
Predrill mounting holes into wall.
Remove cover from fan terminal

12 | P a g e
Cut flue exhaust tube (hot tube) to length
(approximately flush with wall exit). Wall
termination will sit against wall.
Pull flue tube through approx. 100mm further (will
be pushed back once terminal fitted).
Feed power cable through wall and into wall
terminal.
Slide flue onto connection spigot fully. Tighten
clamp fully. Wipe excess silicon, visually check
connection to ensure connection is fully sealed.
Feed air intake flue pipe through location spigot
and fit retaining screw.

13 | P a g e
Push fan terminal into position. And affix to wall.
Uneven or rough surfaces may require sealant
along top and side gaps.
Connect power cable connector. Fit cable clamp to
cable.
Fit front cover

14 | P a g e
ROOFTOP POWERFLUE TERMINATION
Insulation requirements for flue runs
NOTE:
Insulation is used for rooftop termination installations only
The insulation supplied is in lengths of 1000mm
The termination must be installed at a minimum height of 350mm from the lowest point of the
termination to closest point on the roof (Refer image above)
The termination’s spigot and the roof penetration pipe is 250mm in diameter.
Flue length
Insulation Requirement
0 - 5 mts
Uninsulated flue run
5 –8.5 mts
Insulated flue run *
* For 5 - 8.5-meter flue runs, only the supplied insulation must be used and only the exhaust pipe is
to be insulated. The initial 300mm from the appliance exit and the last 700mm from the rooftop
termination may remain uninsulated. However, it is recommended to insulate as much of the
total length as possible.

15 | P a g e
Example: For a flue run of 8.5mts
Flue run length N = 8.5mts
Minimum insulation required X = N - 1 mts
= 8.5 - 1 = 7.5 mts
Insulation is supplied in lengths of 1000mm.
Initial 300mm from appliance exit may remain uninsulated (Refer image below)
Last 700mm from rooftop termination down may remain uninsulated.
Note: The insulation can be cut to shorter lengths to allow for bends.

16 | P a g e
Instructions:
Rooftop fan module –Terminal must be installed
with clearances as specified by AS/NZS 5601.1
Clause 6.9.3
Run exhaust flue and air intake flue as required
Maximum run 8.5mts.Flues can be run next to
each other. Maintain the required clearances to
combustibles.
Insulate flue for runs over 5mts as required.
Rigid glass wool insulation with 25mm wall
thickness.
The insulation is pre-slit and can be fitted around
the flue pipe like a collar
It can also be cut to required size to fit around sharp
bends
Run both flexi pipes from the appliance to the roof
space
Fit insulation on the flexi pipe as shown.
Use aluminium tape to seal the insulation and
ensure its fit snug to the pipe.
Cut insulation to required sizes to fit around
corners.

17 | P a g e
For 90° and 45° bends the corners must be
insulated.
For a 90˚bend with a minimum bend radius is
150mm. Cut the insulation diagonally into 3 pieces
in a cone shape.
On the heater connection end - Fit clamp loosely &
apply silicon inside the pipes. Apply an 8mm silicon
bead fully around the inside of the flue and on the
heater spigot. Smear the silicon around the spigot
and pipe.
Recommended Silicon –Non-acetic, neutral cure
200°C or higher temperature rated. Bostik RTV 922
or similar
Slide flue onto connection spigot fully. Tighten
clamp fully. Wipe excess silicon, visually check
connection to ensure connection is fully sealed.
Repeat above with air intake flue pipe to heater
connection.
Clip flues as required to provide adequate support.
42mm
112mm
42mm
112mm
42mm
112mm
42mm
112mm
Insulation cut pattern for 90° bend

18 | P a g e
Insert the roof penetration and fix firmly to the roof
structure using appropriate supports.
The roof penetration flue is a 250mm rigid flue.
Fit the access panel to the roof penetration
Use the screw holes fix the access panel to the roof
penetration.
Run flue pipes through the access cut outs before
fitting the termination on for ease of installation.
(The picture is a reference only. Take care not to
flex/bend the pipe too sharply and risk slitting the
pipe)
If possible to insulate the flue pipe through the roof
penetration, then fit insulation to the exhaust pipe.
Fit the termination on to the access panel and
match the rivet holes to rivet the termination to the
access panel.
Use only the rivets provided
On the termination end - Fit clamp loosely & apply
silicon inside the pipes. Apply an 8mm silicon bead
fully around the inside of the flue and on the flue
spigot. Smear smoothly around the surfaces.
Recommended Silicon –Non-acetic, neutral cure
200°C or higher temperature rated. Bostik RTV 922
or similar

19 | P a g e
Slide flue onto connection spigot fully. Tighten
clamp fully. Wipe excess silicon, visually check
connection to ensure connection is fully sealed.
Ensure that the pipes are connected correctly and
are not inverted.
Use the labels to identify exhaust and intake spigots
Connect the fan power cable from the appliance to
the termination.
Ensure the cable is clamped only to the intake pipe
to secure the cable from hanging loose & touching
the hot flue gases pipe.
Use the clamp provided. The clamp can be opened
like a collar and fitted around on the flue.
Flex collar and fit around the access panel. Socket
the collar all the way up close to the air intake slots
Ensure there is a rubber seal top and bottom of the
collar.
Use only the screws provided to tightly fit the collar
to seal the access panel.