RealFlame Inspire 700 Installation instructions

INSPIRE FLAME EFFECT SPACE HEATER
MODELS 700/900/ 00
INSTALLATION & OPERATING MANUAL
The Inspire space heater is suitable to be installed into a frame out installation.
Designed to operate on Natural gas and LPG gas. Approval no.GM 10528
VERSION 8

2
WARRANTY INFORMATION
The benefits provided to you under the following warranty are in addition to any other rights and remedies available to
you under the law.
1. Warranty
If:
(a) during the first 15 years from the date of purchase (Firebox Warranty Period), there is a defect in the firebox of the
Gas Burner; or
(b) during the first 2 years from the date of purchase (Parts Warranty Period), there is a defect in the gas valves or
other parts of the Gas Burner,
due to improper workmanship or material, Glen Dimplex will replace or repair the Gas Burner without charge. Any
replacement product is warranted only for the time remaining on the original Firebox Warranty Period or the Parts
Warranty Period as relevant.
2. Registration
You must register to receive the benefit of this warranty by completing the warranty registration on our website
(www.realflame.com.au) or completing and mailing the attached registration card within 30 days of purchase of
your Gas Burner (or, if the Gas Burner is fitted to a new home, within 30 days of the date of settlement of purchase
of such new home).
3. Exclusions
Glen Dimplex is not obliged to replace or repair the Gas Burner under clause 1 if:
(a) it has been improperly stored, installed, connected, used, operated or repaired, or damaged, abused, tampered
with, altered (without our written approval), or not maintained in strict accordance with our installation and
operating instructions; or
(b) it has been installed in an outdoor setting.
4. Limit of Liability
The warranty provided under this warranty is limited to replacement or repair of the Gas Burner only, at our option.
To the extent permitted by law, Glen Dimplex excludes liability for consequential loss or any other loss or damage
caused to property or persons arising from any cause whatsoever, and damage arising from normal wear and tear.
5. Claiming under the Warranty
In order to claim under this warranty you must, within the Firebox Warranty Period or the Parts Warranty Period
(as relevant), contact Glen Dimplex, providing the original proof of purchase and the details below:
Supplier Name___________________________________________________________________________
Date Of Purchase / settlement of property if new home _________________
Model / Serial Number_______________________
This warranty does not cover the cost of claiming under the warranty or transporting the Real Flame Gas Burner to and
from the supplier.
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a
replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage.
You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure
does not amount to a major failure.
If you would like to speak to someone about your Gas Burner or claiming under this warranty, please contact the
Service Warranty Desk on 1300 554 155.
Glen Dimplex Australia Pty Ltd ACN 69 118 275 460
Head Office: 1340 Ferntree Gully Road, Scoresby 3179
Telephone: [phone] Facsimile: [phone]

WARNING
The Inspire space heater has a primary safety glass fitted in front of the glass door. This safety glass is fitted
to this appliance to reduce the risk of injury from burns and at no time should this glass be permanently
removed.
For protection of young children or the infirm, a secondary guard is required.
The appliance is not intended for use by persons (including children) with reduced physical, sensory or
mental capabilitites, or lack of experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for their safety. Children should be
supervised to ensure that they do not play with the appliance.
INSTALLATION NOTICE
The installation of this appliance is only to be carried out by an authorised person in accordance
with the Manufacturer’s Instructions, local gas fitting regulations, AS/NZS5601.1-2013 installation
code for gas burning appliances and any other relevant statutory regulations.
Do not modify this appliance.
In all cases the installation of this appliance shall meet the requirements as set out in
AS/NZS5601.1-2013.
Do not install in a fireplace as a Type 1 installation.
NOTE: A slight smell may be apparent for the first few hours of use. This is due to the heat resistant
paint curing. It is recommended to open windows in the room for the first lighting of the fire. In some
instances a slight discolouration may occur inside the firebox. This is a normal condition and is not
covered by warranty.
IMPORTANT SAFETY NOTICE
DO NOT PLACE ARTICLES ON OR AGAINST THIS APPLIANCE.
DO NOT USE OR STORE FLAMMABLE MATERIALS IN OR NEAR THIS APPLIANCE.
DO NOT SPRAY AEROSOLS IN THE VICINITY OF THIS APPLIANCE WHILST IT IS IN OPERATION.
CARE MUST BE TA EN TO ENSURE THAT ANY RETURN AIR REGISTER OR EXHAUST SYSTEM DOES NOT
ADVERSLEY AFFECT THE OPERATION OF THE APPLIANCE OR DRAUGHT OF CHIMNEY OR FLUE.
APPLIANCE IS DESIGNED TO OPERATE WITH LUMINOUS FLAMES. MAY EXHIBIT SLIGHT CARBON DEPOSIT.
WARNING
The outer glass panel gets extremely hot! Precaution should be taken and young children
supervised at all times when heater is operating.
3
SERVICING
It is recommended you service your gas fire every 2 years as a minimum.
CORD REPLACEMENT
Electrical cord replacement must be undertaken by qualified and trained personnel only.

CONTENTS
Contents .................................................................................................................4
Data Plate ...............................................................................................................5
Dimensions .............................................................................................................5
Installation Instructions ...........................................................................................8
Flue Termination ...................................................................................................10
Installation Instructions
Setup with external wall mounted fan terminal .............................................11
Timber Frame Installation .....................................................................................15
Media Installation..................................................................................................16
Commissioning Procedure....................................................................................29
Operation - User Instructions................................................................................29
Troubleshooting ....................................................................................................35
Remote Control.....................................................................................................36
Wiring Diagram .....................................................................................................37
Aeration Adjustments and Burner Sizes ...............................................................38
Conversion Details................................................................................................39
Parts List...............................................................................................................42
Real Flame Contact Information ...........................................................................44
4

DATA PLATE (Affixed to the base of the unit for reference to gas pressure & consumption)
Inspire 700
GAS TYPE
Natural Gas 1 X 2.30mm 0.88kPa High / 0.40kPa Low
INJECTOR SIZE TPP N.G.C. (Mj/hr)
22.0 High/16.0 Low
LPG 1 X 1.35mm 2.48kPa High / 1.58kPa Low 22.0 High/17.0 Low
Inspire 900
GAS TYPE
Natural Gas 1 X 2.45mm 0.89kPa High / 0.42kPa Low
INJECTOR SIZE TPP N.G.C. (Mj/hr)
24.0 High/16.0 Low
LPG 1 X 1.45mm 2.49kPa High / 1.58kPa Low 24.0 High/19.0 Low
Inspire 1100
GAS TYPE
Natural Gas 1 X 2.65mm 0.88kPa High / 0.41kPa Low
INJECTOR SIZE TPP N.G.C. (Mj/hr)
29.0 High/20.0 Low
LPG 1 X 1.50mm 2.45kPa High / 1.51kPa Low 27.0 High/21.0 Low
5
DIMENSIONS
Max - Min inlet pressure range
Natural gas: 1.13kPa - 5.00 kPa
LPG: 2.75kPa - 5.00 kPa
Inspire 700

DIMENSIONS (continued)
6
Inspire 900
Inspire 1100

7
DIMENSIONS (continued)
Power Flue

LOCATION
Select a location where the fire can be supervised during operation.
An electrical isolation switch must be fitted at the appliance or on an adjacent wall to allow for
emergency shutdown and maintenance.
Installation must meet Australian gas codes AS/NZS 5601.
INSTALLATION CLEARANCES Clearances from combustible materials
Floor 0mm
Sides 5mm
Top 5mm
Flue outer 25mm
Front 250mm
Back 25mm
INSTALLATION CODES
Note appliance gas type – Natural gas or LPG. Should the appliance be the incorrect gas type
please contact the supplier for the conversion kits available for the appliance.
Installers – Please ensure the installation and instruction manuals supplied with this appliance are
supplied to the customer and the customer is trained on how to operate the appliance correctly.
Do not modify the appliance.
Do not exceed maximum rated pressures.
Appliance must be installed as per gas installation code (AS/NZS 5601) and applicable electrical
installation code (AS3000).
Test for gas leaks prior to operating appliance.
Check gas pressures and adjust if incorrect.
WARNING - Transit material such as cardboard packaging, pallet, plastic wrap, glass packaging
warning labels and burner media protection must be removed prior to use.
FLUE CONFIGURATIONS
Flue configurations are a maximum of 5m, flue runs less than 5m are permitted. Aluminium flexible
flue is used for for both the inlet and outlet.
Flue runs 5m or less (75mm dia Aluminium flexi flue)
Inlet pipe - Maximum flue run 5m total length including 5 x 90 bends
Outlet pipe - Maximum flue run 5m total length
including 4 x 90 bends
Appliance is supplied with a 2 x 5m flexible flue lengths.
Flue can be cut to length as required.
Recommended bend radius 150mm or larger.
Bends must not form a P Trap.
Flue must be clipped and supported support.
Connections must be sealed with silicon and clamped
where advised.
Recommended Silicon – Non acetic, neutral cure 150degc
or higher temperature rated. Bostik RTV 926 or similar.
U style flue runs must not be installed
8

9
INSTALLATION INSTRUCTIONS (continued)
FLUE TERMINATION LOCATION
• Flue terminations shall not be recessed in walls or sidings.
•EXTREMELY IMPORTANT: In heavy snow areas take extra care to prevent blocking
flue termination with snow removal equipment.
• Flue gases exiting flue terminals are very hot and must not be restricted to assure fireplace
combustion is not affected.
• Do not place, build any obstruction, plant any bushes or for any reason attempt to conceal
the flue termination. To do so will affect the operation of the fireplace and may be hazardous.
• This unit must always vent directly to outdoors.
GAS CONNECTION 15mm (1/2”) Compression union
ELECTRICAL CONNECTION 3 Pin 10 Amp GPO plug
POWER RATING OF APPLIANCE 230V 50Hz 0.8Amp

INSPIRE FLUE TERMINAL LOCATION
10

11
INSTALLATION INSTRUCTIONS (continued)
SETUP WITH EXTERNAL WALL MOUNTED FAN TERMINAL
Wall mounted fan terminal
1/ Wall mounted fan module – terminal must be
installed with clearances as specified by AS/NZS
5601.1 Clause 6.9.3
2/ Run exhaust flue and air intake flue as required
– Maximum run 5m. Flues can be run next to each
other. Maintain the required clearances to
combustibles.
3/ Connection to appliance
Cut tube to length where required.
Ensure ends are burr free and round, test fit flue
will slide over connection.

INSTALLATION INSTRUCTIONS (continued)
12
Recommended Silicon – Non-acetic, neutral cure 150degc or higher temperature rated.
Bostik RTV 926 or similar.
Apply an 8mm thick silicon bead fully around heater connection approx. 10mm from the top.
Apply an 8mm thick silicon bead fully around the lower fan connection spigot approx. 10mm from
the end.
Apply an 8mm silicon bead fully around
the inside of the flue end (heater
connection end)
Fit flue clamp over flue (loosely).
Slide flue onto connection spigot fully.
Tighten clamp fully.
Wipe excess silicon, visually check connection to
ensure connection is fully sealed.
4/ Repeat above with air intake flue pipe to heater
connection.
5/ Clip flues as required to provide adequate support.
6/ Connection to wall mounted fan terminal
Predrill mounting holes into wall.

13
INSTALLATION INSTRUCTIONS (continued)
Remove cover from fan terminal
Cut flue exhaust tube (hot tube) to length
(approximately flush with wall exit). Wall
termination will sit against wall.
Pull flue tube through approx. 100mm further
(will be pushed back once terminal fitted).
Feed power cable through wall and into wall
terminal.

INSTALLATION INSTRUCTIONS (continued)
14
Slide flue onto connection spigot fully.
Tighten clamp fully. Wipe excess silicon,
visually check connection to ensure
connection is fully sealed.
Feed air intake flue pipe through location
spigot and fit retaining screw.
Push fan terminal into position. And affix to
wall.
Uneven or rough surfaces may require
sealant along top and side gaps.
Connect power cable connector. Fit cable
clamp to cable.
Fit front cover

TIMBER FRAME INSTALLATION
Plaster to run
beyond stud and
behind trim
TRIM
2 x 84mm OD
FLUES
* Indication only. Can be smaller or larger.
A
B
A B C D*
580 710 400 1500
910
1110
Frameout Dimensions (in mm)
C
D*
15

MEDIA INSTALLATION
Media must be setup as per instructions
• The media is designed and shaped to correctly locate and remain in the correct position.
• DO not add extra media, or combine media types.
• Only the approved supplied media is to be used.
• Do not use any other media than as supplied and recommended by the manufacturer.
Use of other media may result in explosive media which may cause injury or damage.
MEDIA TYPES
1. Driftwood
2. Pebbles
Refer to correct section for media set up.
Place branch log 1 supports as shown.
Place No 2. long log across branch log, using location grooves to locate.
Driftwood Media Inspire 700 Model
16

MEDIA INSTALLATION (continued)
Place No 3 log short crossover log over the long log, use location groove to locate.
Place log No 4 over log 3, use groove to locate.
Place the second branch log 1 onto support.
17

MEDIA INSTALLATION (continued)
Place 2nd log No. 2 log onto branch log, use location grooves to locate.
Place 2 log No 3 onto long log, use location groove to locate.
Place mixed coals around logs along front section, DO NOT PLACE ON BURNER.
18

MEDIA INSTALLATION (continued)
Locate side trays on either side of the firebox. Ensure that they are sitting flush against the side
walls and screw them in from the front (if the trays do not sit flat then use the rear screw holes to
screw them down).
Pebbles Media - Inspire 700 Model
Randomly arrange pebbles around the media trays front and back. One medium size pebble to sit
on each of the side trays. DO NOT PLACE ANY MEDIA ON THE BURNER.
19

MEDIA INSTALLATION (continued)
900 MODEL - Place Log 5 as shown in the image below. Near LH end.
Place log 6 across log 5 using location grooves to locate.
Driftwood media - Inspire 900 Model
Place log 1 as shown in the image below.
20