Rear view safety RVS-CW-CAM User manual

1
TM

What’s in the Box?
• 1 Quad View Digital Wireless Monitor with Cigarette
Lighter Adaptor
• 1 CCD Wireless Backup Camera with Power Cable
• 1 Extendable Suction Cup Mount for Monitor

3
Table of Contents
Introduction....................................................................................................4
Safety Information ...................................................................................5-7
Before Beginning Installation....................................................................8
Installation Guide..........................................................................................9
Pairing ............................................................................................................10
System Operation........................................................................................11
Operational Diagram..................................................................................12
Installation Diagram ..................................................................................13
Monitor Dimensions...................................................................................14
Monitor Specifications..............................................................................15
Camera Dimensions .................................................................................. 16
Camera Specifications...............................................................................17
Splitting.........................................................................................................18
Positioning....................................................................................................19
Troubleshooting...........................................................................................20
Warranty........................................................................................................21
Disclaimer .....................................................................................................22

REAR VIEW SAFETY
4
Introduction
Congratulations on purchasing a Rear View Backup Camera Sys-
tem. With this manual you will be able to properly install and op-
erate the unit.
The Backup Camera System is intended to be installed as a
supplement aid to your standard rear view mirror that already ex-
ists in your vehicle. The Backup Camera System should not be
used as a substitute for the standard rear view mirror or for any
other mirror that exists in your vehicle.
In some jurisdictions, it is unlawful for a person to drive a
motor vehicle equipped with a TV viewer or screen located for-
ward of the back of the driver’s seat or in any location that is vis-
ible, directly or indirectly, to the driver while
operating the vehicle.

5
Reverse With Confidence

Safety Information
Please read the entire manual and follow the instructions and
warnings carefully. Failure to do so can cause serious damage
and/or injury, including loss of life. Be sure to obey all applica-
ble local traffic and motor vehicle regulations as it pertains to
this product. Improper installation will void manufacturer’s
warranty.
USAGE
•The Rear View Camera System
is designed to help the driver
safely detect people and/or
objects helping to avoid
damage or injury. owever,
you the driver, must use it
properly. Use of this system is
not a substitute for safe,
proper or legal driving.
•Never back up while looking
at the monitor alone. You
should always check behind
and around the vehicle when
backing up, in the same way
as you would if the vehicle
did not have the Rear View
Camera System. If you back
up while looking only at the
monitor, you may cause
damage or injury. Always
back up slowly.
•The Rear View Camera
System is not intended for
use during exstensive back-up
maneuvers or backing into
cross traffic or pedestrian
walkways.
•Please, always remember,
the area displayed by the
Rear View Camera System is
limited. It does not display
the entire panorama that is
behind you.

INSTALLA TION
•Electric shock or product
malfunction may occur if
this product is installed
incorrectly.
•Use this product within
the voltage range specified.
Failure to do so can cause
electronic shock or product
malfunction.
•Take special care when
cleaning the monitor.
•Make sure to firmly affix the
product before use.
•If smoke or a burning smell
is detected, disconnect the
system immediately.
•Where the power cable may
touch a metal case, cover the
cable with a friction tape. A
short circuit or disconnected
wire may cause a fire.
• While installing the Rear
View System be careful with
the wire positioning in order
to avoid wire damage
•The Rear View System
should only be used when
the vehicle is in reverse.
•Do not watch movies or
operate the monitor while
driving; as it may cause an
accident.
•Do not install the monitor
where it may obstruct drivers
view or obstruct an air bag
device.
•Dropping the unit may cause
possible mechanical failure.
REAR VIEW SAFETY
6
Safety Information

7
Reverse With Confidence

Safety Information
IN NO EVENT S ALL SELLER OR MANUFACTURER BE
LIABLE FOR ANY DIRECT OR CONSEQUENTIAL DAMAGES OF
ANY NATURE, OR LOSSES OR EXPENSES RESULTING FROM
ANY DEFECTIVE PRODUCT OR T E USE OF ANY PRODUCT.
If you have questions about this product, contact:
Customer Service:
Rear View Safety
1797 Atlantic Avenue
Brooklyn, NY 11233
Tel: [phone]

REAR VIEW SAFETY
8
Before Beginning Installation
Before drilling please check that no cable or wiring is on the
other side of the wall. Please clamp all wires securely to reduce
the possibility of them being damaged while vehicle is in use.
Keep all cables away from hot or moving parts and electrical
noisy components.
Step 1: Choose the monitor and camera locations.
Step 2: Install all cables in vehicle, when necessary a 0.8 (20mm)
hole should be drilled for passing camera cable through vehicles
walls. Install split grommets where applicable
Step 3: Once all cables and wiring have been properly routed and
the system has paired, perform a system function test by tem-
porarily connecting the system. If the problem persists see trou-
bleshooting (page 20).
Before Beginning Installation

9
Reverse With Confidence

Installation Guide
We recommend doing a benchmark test before installation
to insure that all components are working properly.
SYSTEM COMES PAIRED.
• But if there is no image on monitor, your system is NOT paired
and needs to be paired. (see page 10)
Camera Connection:
• Locate the clearance lights wiring on your vehicle. You
may need to remove the interior panel in order to locate.
Connect the power cables for camera: Red wire to light's
positive; Black wire to chassis ground.
Monitor Connection:
• Firmly insert the lighter plug to cigarette lighter socket.
Do not install the monitor where it may obstruct driver’s view
or obstruct and air bag device.
.............................................................................................................................
Cleaning
• If dirt, rain or snow attaches to the camera, the monitor may
not clearly display objects.
• Do not use alcohol, benzene or thinner to clean the camera.
This will cause discoloration. To clean the camera, wipe with a
clean cloth dampened with mild cleaner diluted with water
and then wipe with a dry cloth.

REAR VIEW SAFETY
10
Pairing
1. Press MENU on monitor and it will bring you to
“camera settings” screen. (see screen 1)
2. Press MENU 2nd time you will see “pairing” option. (see screen 2)
3. Press MENU 3rd time and camera 1 is selected.
(see screen 2)
Select camera 2 (Back-up camera), using the up/down arrow.
4. Remove screw from back of the camera to reveal “Pair Button”
(See diagram page 12).
5. Press MENU a 4th time to begin pairing process. During pairing
mode, hold the “Pair button” the the back of the camera for 5 full
seconds then push the “Pair button” on the back of the camera
(see diagram page 12). The button must be pressed within 5 sec-
onds of starting the pairing process, so for the greatest ease the
pairing process should be done BEFORE the camera is installed on
your vehhilce.You will see “Pair OK” on the screen when it suc-
cessfully pairs. If you see “Time out”, please repeat all steps.
Screen 1
Screen 2

11
Reverse With Confidence

System Operation
• To turn on the monitor, press “POWER ON” button.
• To get to Main Menu, press “MENU” 1 time
• To get to Camera Settings, press “MENU” 2 times, use arrows to
get to System Settings.
Camera Settings:
To adjust Pairing, Activation, Brightness or Volume
• Use arrows to reach desired item. When there, Press “MENU”
and use arrows
• To return to Main Menu, press “EXIT SELECTION”
(See Operational Diagram on Page 12)
System Settings:
Power Saving, Distance Grid or Default Setting
• Use arrows to reach desired item. When there, Press “MENU”
and use arrows (See Operational Diagram on page12).
Screen 3

REAR VIEW SAFETY
12
Operational Diagram
MENU
EV
CAM
t
t
POWE
ON / OFF
MENU/
SELECTION
BUTTON
CAME A
SELECTION
DOWN
A OW
UP
A OW
OTATION
IMAGE
(Exit when in
MENU
mode)
QUAD MONITOR
BLACK
G OUND
ED
POSITIVE
INLINE
FUSE
CAMERA
PAI
BUTTON

13
Reverse With Confidence

Installation Diagram
Figure 1.1 Figure 1.2
Figure 1.3 Figure 1.4
Connection of U
Bracket
Connection of
Flushmount Bracket
On Select Models

REAR VIEW SAFETY
14
Monitor Dimensions
with
sun
shade
5.25”
7”
Power
On/Off
Menu/
Selection
Button
Camera
Selection
Down
Arrow
Up
Arrow
otation
Imager
(Exit in
Menu
Mode)

15
Reverse With Confidence

Monitor Speciifications
TFT LCD Digital Monitor
Screen Size 7”
Dot Resolution 800 x 3 (RGB) 480V
Display Format 16:9 / 500:1
Display Brightness 400cd/m2
Viewing Angle U:50° / D:60° / R:70°
Video Input 4 channel
Video Source 1Vp-p, 75Ω
Power Supply DC 12V(+/- 10%)
Power Consumption 5W
Operating Temperature -30°C ~ +80° C
Video System Auto NTSC/PAL
Overall Dimensions 7”Lx 5” x 1”D
Weight 400G
Impact Rating 5G
Dot Pitch 0.192 x 0.1805V
Sync System Internal

REAR VIEW SAFETY
16
Camera Dimensions
3.25”
3”

17
Reverse With Confi-
Camera Specifications
Camera 1/4” Sharp® Color CCD
Picture Elements 250,000 pixels
Gamma Correction r=0.45 to 1.0
Image Sensor 480TV lines
Lens 2.1mm
View Angle 130°
Sync System Internal Synchronization
Infrared distance 50 Feet (12 Infrared)
Usable Illumination 0 Lux (IR On)
Power Source DC 12V (+/- 10%)
S/ Ratio More than 48dB
Electronic Iris 1/50, 160-1/100,000sec
Video Output 1Vp.p 75ohm
IR Switch Control ACDS Automatic Control
Impact Rating 20G Vibration/100G Shock
Operating Temperature -30°C - +60°C/RH 95%Max
Storage Temperature -30°C - +60°C/RH 95%Max
Waterproof Rating IP68

REAR VIEW SAFETY
18
Splitting
Installing & Splitting Embedded Monitor
Installing sun shield: Put shade cover on
the display. Installing back cover: Put the
monitor with shade cover in the back cover
(only for embedded monitor)
Splitting back cover: old monitor with 2
hands and detach with fingers, as indicated
by arrows. (only for embedded monitor)
Splitting sun shield: Take the monitor with
the left hand and detach with right hand as
indicated by the white arrow. (see below)

19
Reverse With Confidence

Positioning
Rear Camera Positioning

REAR VIEW SAFETY
20
Troubleshooting
Monitor Display Blue Screen & Displays No Signal
•Do a hard reset, unplug all
cables and power cables leave
out for 1 minute and then
re-connect them.
•Check to ensure that the con-
nection to the camera is tight.
No Image On Screen
•Verify camera is on correct
camera input
•Verify camera is connected
to power/ground
Audio on Camera
•Verify chosen camera has audio •Verify volume setting
NOTE: VERIFY T E SYSTEM IS PAIRED