Rebotec Phoenix User manual

REBOTEC®Rehabilitationsmittel GmbH
DE-49610 Quakenbrück, Artlandstr. 57-59
Telephone: [phone]-
Fax: [phone]
Web: www.rebotec.de
BA-Nr.: 02.07.135/2023-05-A01 E-Mail: [email protected]
Read this user manual before using the device for the first time and keep it at hand for the
user as well as for future use and subsequent sales.
EN
User manual
Multifunctional nursing wheelchair
XX = colour code
Figure similar
Phoenix
Phoenix 200
350.xx.10
350.xx.40
353.xx.12
353.xx.40
150 kg
150 kg
200 kg
200 kg

REBOTEC / BA-Nr.: 02.07.135/2023-05-A01
- 2 -
EN
Table of contents
Multifunctional nursing wheelchair.......1
1Product description .......................3
1.1 Introduction .............................................3
2Features ..........................................3
2.1 Intended purpose ....................................3
2.2 Conditions of use....................................4
2.3 Storage & transport.................................4
2.4 Equipment & functions...........................4
2.5 Packaging ................................................4
2.6 Disposal ...................................................4
3Symbols & nameplates..................4
4Safety instructions.........................5
5Incident reporting...........................6
6Warranty..........................................6
6.1 Complaint.................................................6
7Reuse, lifetime................................6
8Scope of delivery............................6
9Setting up for use...........................6
9.1 Folding down the footrests....................6
9.2 Adjusting the footrest height.................6
9.3 Operation of the parking brake..............7
9.4 Mounting of the headrest .......................7
9.5 Adjusting the headrest ...........................7
9.6 Adjusting the tilt......................................7
10 Product data ...................................8
11 Operation of the product ...............8
11.1 Sitting down.............................................8
11.2 Standing up..............................................8
11.3 Folding down the armrests ....................9
11.4 Folding down the footrests....................9
11.5 Removing the footrests..........................9
11.6 Removing the seat cover........................9
11.7 Use of the toilet bucket.......................... 9
12 Troubleshooting.............................9
13 Cleaning & disinfection................10
13.1 General information ............................. 10
13.2 Cleaning ................................................ 10
13.3 Disinfection........................................... 10
14 Maintenance..................................11
15 Spare parts & accessories...........12
16 Drawing & dimensions.................13

REBOTEC / BA-Nr.: 02.07.135/2023-05-A01
- 3 -
EN
1 Product description
350.xx.10 & 353.xx.12
350.xx.40 & 353.xx.40
Figure shows:
A
Rotation adjustment for PUR headrest
B
Backrest
C
Armrest
D
Locking bolts
E
Chair frame with tilt adjustment
F
Wheel insert with parking brake
G
PUR headrest
H
PUR backrest cushion
I
PUR seat, hygiene opening and bucket
holder
J1
PUR seat cushion
J2
PUR transport seat
K
PUR leg support
L
Foot support with footrest
M
Locking lever for tilt adjustment
N
Toilet bucket with lid
O
Nameplate
1.1 Introduction
•The product described here is a medical device of
risk class I according to (EU) 2017/745 MDR.
•In this user manual, you will find information on the
safe and proper initial operation, use, maintenance
and care of this product.
•Carefully read this user manual before using the
product. Follow the safety instructions and act ac-
cordingly.
2 Features
•The product is designed for people with adult body
proportions. Their body weight should be
40 to 150 kg for Phoenix
40 to 200 kg for Phoenix 200
and they should have a minimum height of 146
cm.
2.1 Intended purpose
350.xx.10 & 353.xx.12
•The product is intended for the care of patients with
limited ability to stand and/or walk. It ensures
showering while sitting or lying down and going to
the toilet, even if a conventional toilet or bathroom
is out of reach. It can be infinitely adjusted between
sitting and lying positions. The patient must have
sufficient sitting ability and upper body muscula-
ture. If necessary, a nurse must be present during
use. The product is not intended for prolonged sit-
ting and transfer.
350.xx.40 & 353.xx.40
•The product is intended for the care of patients with
limited ability to stand and/or walk. It allows you to
shower while sitting or lying down. It can be infi-
nitely adjusted between sitting and lying positions.
The patient must have sufficient sitting ability and
upper body musculature. If necessary, a nurse
must be present during use. The product is not in-
tended for prolonged sitting and transfer.
Specification:
•Maximum user weight
Phoenix: 150 kg
Phoenix 200: 200 kg
•Height adjustable footrests
•Wheelchair, 4 swivel castors, lockable
•Indoor use
J2
A
B
C
D
F
E
G
H
I
J1
K
L
M
N
O

REBOTEC / BA-Nr.: 02.07.135/2023-05-A01
- 4 -
EN
Indication
•Use in domestic and inpatient settings.
•Medical condition of the patient:
•The use of a chair by patients with cognitive disor-
ders (reduced mental, physical, sensory or intellec-
tual abilities) must be decided in advance by a
medical decision (prescription of the product) or on
site by the nursing personnel.
2.2 Conditions of use
•Temperature range: 5°C to 35°C; direct radiant
heat on the product must be avoided.
•Relative humidity: 40% to 75%. Outside of these
conditions, the product must only be used for a
short time.
•This product may not be used to transport heavy
objects.
•There must be a flat surface of sufficient size for
the product to be placed on. See 16.
2.3 Storage & transport
•Temperature range: 5°C to 25°C; direct radiant
heat on the product must be avoided.
•Store the product in dry rooms with a humidity of
up to 65%.
•The shower should be designed so that there is a
flat surface of sufficient size.
2.4 Equipment & functions
•The chairs consist of a plastic frame on 4x5” swivel
castors with locking brake. The armrests can be
swivelled and have an armrest locking device.
•The footrests are height adjustable and can be re-
moved or folded down. The headrest is height ad-
justable and rotatable. A tilt adjustment of the chair,
via a lever function, for the supine position of the
patient
•Depending on the equipment variant, there is a
PUR seat for transport purposes or a PUR seat
with hygiene cut-out (incl. toilet bucket with lid).
•Due to the design and intended use of the product,
disassembly for transport or storage is not in-
tended or necessary.
2.5 Packaging
•We recommend you keep the packaging for a later
transport.
•Dimensions: 1005mm x 670mm x 900mm
2.6 Disposal
•Disposal and recycling of used products and pack-
aging must be carried out in accordance with cur-
rently valid regulations. Please contact a disposal
company for further information.
•The Infection Protection Act must be observed.
•Please observe any labels and information on
packaging material and act accordingly.
3 Symbols & nameplates
Figure similar.
The nameplate must not be removed! For
ordering spare parts and processing com-
plaints, the device name, serial number and year of
manufacture will be required.
Symbol
Meaning
Symbol
Meaning
Read the
manual!
Year of
manufac-
ture of De-
vice
Serial num-
ber
Important
information!
Article num-
ber
Maximum
user weight
in kg
Care in-
structions
Mainte-
nance in-
structions
Applicable
for indoor
use only.
Manufac-
turer
Visual sig-
nal
Language
Read the
user man-
ual!
Do not dis-
pose of as
household
waste.
Product complies with (EU) 2017/745
MDR
EN

REBOTEC / BA-Nr.: 02.07.135/2023-05-A01
- 5 -
EN
Symbol
Meaning
Symbol
Meaning
Caution!
Observe the safety instructions
Unique Device Identifier
(Data: GTIN / LOT (SN) / year of man-
ufacture)
Medical device label
This product is a medical device.
4 Safety instructions
Please observe the following safety in-
structions:
•Before using the device for the first
time, the User Manual must be read completely in
order to avoid hazards or damage caused by
maloperation.
•Before each use, check the product for visible dam-
age or deficiencies.
•In case of malfunctions or damage of any kind, the
product must not be used.
•Do not leave the patient unattended during use.
Caution: Danger of falling!
•Use of the product should be assisted by a trained
caregiver, depending on the health condition of the
patient.
•When adjusting the backrest, the patient should
hold on to the armrests.
•Patients who are prone to uncontrolled actions or
movements must be supervised when using the
chair.
•The chair must only be moved on a slope or incline
with the help of a caregiver. Generally, on an uphill
slope the chair should be pushed forward and on a
downhill slope it should be pulled backward.
Caution: Danger of slipping!
•Before use, check that the seat surfaces are firmly
clamped in the seat frame.
•Always lock at least 2 parking brakes on the
wheels before using the chair to prevent the chair
from rolling away.
•When sitting down, do not sit on the front edge of
the seat or on the seat cushion; the user should
take up the entire seat surface.
Caution: Danger of tipping over!
•The chair must only be used with the armrests
locked in place when sitting, moving about and/or
adjusting the tilt angle.
•The product may only be pushed by the push han-
dle.
•The footrests must be swivelled down or folded up
before sitting down/standing up. Do not stand on
the footrests!
•Do not move against door thresholds, edges or
other uneven surfaces.
•Only use indoors and on flat, skid-proof surfaces.
•Only move at a moderate walking pace.
•Persons must only be transported in an upright sit-
ting position.
•Do not lean out of thechair at any time. If the swivel
castors are in an unfavourable position (pointing in-
wards), stability of the chair is limited.
•Special care must be taken when moving the chair
in a tilted position!
Caution: Danger of breakage!
•The product is only suitable for the intended use.
Observe the permissible max. body weight. See 2.
Caution: Danger of pinching or catching!
•Do not leave the patient unattended during use.
•When folding the armrests up or down, do not
reach into the joint guide so that no parts of the
body etc. are trapped. Keep body parts away from
inside the armrests.
•Do not reach between the seat plate and the frame
when pushing on the seat plate and during tilt ad-
justment to prevent any body parts from being
trapped.
•When folding down the footrests, take care to avoid
trapping any body parts. Keep body parts away
from the recess in the heel area.
•When adjusting the headrest, make sure that no
parts of the body or any objects are trapped. Keep
body parts away from between the backrest and
the headrest.
•When pulling out and pushing in the toilet bucket,
there is a risk of trapping soft tissue of the patient.
To prevent injuries, the bucket may only be pulled
out or pushed in when no user is sitting in the chair.
Caution: Risk of injury!
•There is a risk of injury with surface temperatures
> 40°C. Therefore, do not expose the product to
high temperatures (e.g. sunlight, radiators, hot wa-
ter). Allow the product to cool down before use.
If the product is used by patients with insen-
sitive skin (no temperature perception or
skin damage), a heat check (e.g. touching with the

REBOTEC / BA-Nr.: 02.07.135/2023-05-A01
- 6 -
EN
back of the hand) must be carried out by the nursing
staff.
5 Incident reporting
•Serious incidents in connection with the product
must be reported immediately to the manufacturer
and the competent authorities.
▪Use the reporting functions and provided
forms.
Manufacturer: [e-mail]
6 Warranty
•For this product the manufacturer grants a war-
ranty of 12 months. Compliance with the general
terms and conditions (www.rebotec.de/agbs), as
well as the intended use, are a basic prerequisite.
The statutory warranty provisions shall apply.
•Unauthorised modifications to this product will void
the product’s conformity and the warranty.
6.1 Complaint
•Please contact us before returning the product.
•To reduce transport damage, use the original pack-
aging if possible.
•The Infection Protection Act must be complied
with.
•Please make sure that the product does not pose
a risk of infection when returned.
•Enclose the supplied information sheet on safety
with the product.
•Costs may incur for returns that are not marked
non-objectionable.
7 Reuse, lifetime
•The product is suitable for reuse. How often the
product can be reused depends on the frequency
and nature of use.
•Before reuse, the product must be reprocessed hy-
gienically and the technical and functional safety
and reliability of the product must be checked and
restored if necessary. See 13.
•For more detailed information, please see the re-
processing instructions (02.12.158) and the
maintenance instructions (02.11.151).
•The documents can be downloaded from the fol-
lowing link.
▪www.rebotec.de/downloads
•When used as intended, the product has a lifetime
of 5 years. The effective lifetime may vary depend-
ing on the frequency and intensity of use and the
general condition. The lifetime of the product can
be extended by lower intensity of use.
8 Scope of delivery
•1x Multifunctional nursing wheelchair
1x Headrest unit, shape 1
1x Toilet bowl (Phoenix 200 only)
1x Toilet bucket with lid
•1 User manual (02.07.135)
•The reprocessing and maintenance instructions
can be ordered or viewed and downloaded at
www.rebotec.de/downloads.
9 Setting up for use
•The product has been carefully inspected in the
factory for freedom from defects and complete-
ness. Please check the product for any possible
damage which may have occurred during transport
and for completeness of the scope of delivery upon
receipt. Assembly or adjustment shall be carried
out by the specialist dealer.
9.1 Folding down the footrests
•Turn (1) the footrests forwards until they engage
automatically. Fold (2) the footrests down. Adjust
the height of the footrests if necessary.
9.2 Adjusting the footrest height
The footrest height can be adjusted in 4 positions.
Loosen and remove the screws on the side of the
footrest using an Allen key (SW 5). Select the appro-
priate height level (1-4) and screw the footrest back
in place. Make sure that the screws are firmly tight-
ened!
1
2

REBOTEC / BA-Nr.: 02.07.135/2023-05-A01
- 7 -
EN
9.3 Operation of the parking brake
•With your foot, press down the parking brake lever.
The wheel is now braked and fixed in its direction.
The wheel is released by lifting the actuating lever
with the foot
9.4 Mounting of the headrest
•Fold the levers (A) upwards and insert the tubes of
the headrest unit into the openings.
•Push the tubes down until the push button (C) en-
gages in the hole (B)
•Then push the push button (C) all the way in and
push the tubes to the end stop and fold the levers
(A) all the way down.
9.5 Adjusting the headrest
•To adjust the headrest height, fold up the two lev-
ers (A) and slide the headrest to the appropriate
height
•The headrest is continuously adjustable (120 mm)
until the push button (B) engages in the hole.
•After adjustment is completed, fold the two levers
(A) all the way down again. By removing the clips
(C), the headrest can be removed for cleaning or
replacement.
•By turning the rotary head (A) you can adjust the
tilt of the headrest.
Attention! Risk of crushing (B) of body
parts between headrest and backrest
cushion.
9.6 Adjusting the tilt
•The backrest can be continuously tilted backwards
by approx. 37 degrees, and the seat surface can
be adjusted by 12 degrees.
•Pull the locking lever (A) vertically upwards and
then press down on the backrest (B) to the desired
position.
•Push the locking lever (C) all the way down again.
Seat position
Tilt position
Min
Max
C
down
up
A
B
A
C
D
A
B
D
A
C
B

REBOTEC / BA-Nr.: 02.07.135/2023-05-A01
- 8 -
EN
Maintenance instructions
If operation of the locking lever is too stiff or
too loose, the clamping effect can be read-
justed.
•Dismantle the cover. Using an Allen key (SW5), the
clamping effect of the lever is increased by turning
to the right and reduced
by turning to the left.
Then press the cover
firmly back on and lock
the armrest into place.
10 Product data
•We reserve the right to make technical develop-
ments and improvements with respect to the de-
sign shown in this user manual.
•See 16.
Characteristic
Value
Phoenix / 350.xx.10
2.
Product weight*
29.3 kg
3.
Total weight*
35.3 kg
Phoenix / 350.xx.40
2.
Product weight*
28.4 kg
3.
Total weight*
34.4 kg
Phoenix 200 / 353.xx.12
2.
Product weight*
34.8 kg
3.
Total weight*
39.4 kg
Phoenix 200 / 353.xx.40
2.
Product weight*
34.0 kg
3.
Total weight*
38.6 kg
Skin compatibility
DIN EN 10993-1/-5
Flammability**
DIN EN 1021-1/-2
*Without accessories.
**Flame retardant: For products made of PUR ma-
terial.
11 Operation of the product
•Before use, it must be ensured that the product is
in proper operating condition. If defects or malfunc-
tions are evident, the product must not be used.
Have the defects corrected by a specialist dealer
before use.
If necessary, depending on the patient's
limitations, sitting down and standing up
must be done with the help of a caregiver.
Subsequent adjustments may only be made by
qualified personnel!
11.1 Sitting down
•Before sitting down and standing up, make sure
that the product is securely positioned to prevent it
from slipping or tipping over,
that at least two wheels are
braked, that the armrests are
properly engaged, that the
seat surfaces are firmly in
place, and that the footrests
are folded to the side or up.
•The patient must po-
sition themselves as close as
possible to the product. By supporting themselves
on the two armrests, the patient should slowly sit
down on the cushion.
•If this is not possible due to their physical limita-
tions, support must be provided by the nursing
staff. If necessary, the use of a lifting aid or patient
lift is advisable.
Caution: Danger of falling!
•Falling down or
slumping on the chair seat
must be avoided. The patient
should sit on the full chair sur-
face, if possible, and not only
on the edge of the seat.
•When transporting
people, the entire surface of
the backrest and the footrests
must be used if possible.
11.2 Standing up
•Before standing up, make sure that the chair is se-
curely positioned to prevent it from slipping or tip-
ping over, that at least two wheels are braked,
that the armrests are properly engaged, that the
footrests are folded to the side or up and that the
patient sits upright.
•The patient should move forward on the chair so
that the feet are on the floor.
The patient must support
themselves with their arms
on the armrests and slowly
rise from the seat.
•Do not lean your
body too far forward to avoid
a potential risk of falling.
•The patient should
be helped to stand up by the nursing staff.
2.
3.
1.

REBOTEC / BA-Nr.: 02.07.135/2023-05-A01
- 9 -
EN
Caution: Danger of falling!
•Do not lean on the
footrests when sitting down
or standing up.
11.3 Folding down the armrests
•Pulling out the locking bolts (A) releases the lock-
ing mechanism, and the armrests can be swivelled
backwards.
•When folding up the armrest, check that the catch
on the backrest (B) and the locking bolt (A) are
seated correctly. The armrests can be swivelled
with both hands.
•To do this, keep the locking bolt (A) pulled during
the entire swivelling process and guide the armrest
to point (C) with the other hand. Only touch the
outer area and do not reach into or through the
armrest.
Check the locking at regular intervals, as
possible limescale deposits on the locking
mechanism can impair function and smooth
operation.
11.4 Folding down the footrests
•First swivel the footrests upwards and then lift the
footrest out of the catch on the wheel. The footrest
can now be folded back to the side.
11.5 Removing the footrests
•Raise the footrest by approx. 100 mm and turn it
outwards by 90 degrees. Loosen the front cover on
the side frame.
•Now you can push the footrest all the way up and
pull it out. Clamp the cover back on.
11.6 Removing the seat cover
•The seat with (I) and without (O) hygiene cut-out,
the foot cushion (K) as well as the back cushion (H)
can be removed from their locking mechanism on
the chair frame for cleaning purposes or for re-
placement. Page 1.
11.7 Use of the toilet bucket
•When using the chair with the toilet bucket, use
only in the sitting position and not in the lying posi-
tion, otherwise the toilet bucket will fall down.
Attention! Remove the bucket before
tilting the chair!
Handling
•Slide the toilet bucket (A) under the seat from the
back. Remove the toilet lid (B) beforehand.
•To remove, slightly lift the toilet bucket and then
pull it out backwards.
•The armrests must be locked to prevent the patient
from falling out. After removing the toilet bucket,
put the seat cushion (C) back onto the shower seat.
12 Troubleshooting
Fault
Potential cause
Remedy
Armrest can-
not be swiv-
elled down
Deposits in the
locking device
(locking bolt)
Cleaning,
checking reg-
ularly
Locking bolt
cannot be
pulled out
Deposits, tension
spring jammed or
defective
Cleaning,
Replace the
locking bolt
Footrest can-
not be folded
down
Deposits in the
joint,
Bracing
Cleaning,
Check screw
connection
Wheel lock
does not brake
General defect
see mainte-
nance!
Turning the
wheel is stiff
Deposits
Cleaning
Wheel does
not turn
General defect
see mainte-
nance!
A
C
B
4.
C
A
B

REBOTEC / BA-Nr.: 02.07.135/2023-05-A01
- 10 -
EN
Fault
Potential cause
Remedy
Uneven run-
ning of the
wheel
Severe uneven
tread wear
see mainte-
nance!
Chair frame
too unstable
Screw connections
too loose
Screw con-
nections:
Tighten
frame, wheel
inserts
Wheel insert
bent/distorted
Hitting an obstacle
see mainte-
nance!
Lever for tilt
adjustment
does not func-
tion
Jammed, broken,
deposits
Screw connections
too loose or too
tight
Inspection,
Maintenance
No function of
tilt adjustment
Functional defect
Inspection,
maintenance
No function of
headrest ad-
justment
Functional defect
Inspection,
maintenance
13 Cleaning & disinfection
13.1 General information
Attention: Danger of pinching or catch-
ing when cleaning the footrests!
•Please note section 4.
•The product is not suitable for machine cleaning
and disinfection. Please observe the reprocessing
instructions (01.12.158).
Only the bucket is suitable for machine cleaning
and disinfection.
•Do not use hard objects such as spatulas, wire
brushes or metal sponges.
•Observe protection against infection. Disinfect the
article before reuse.
•Do not mix different detergents & disinfectants.
13.2 Cleaning
•Coarse soiling must be removed immediately after
use.
•The seat cover, seat, leg support and bucket must
be disassembled before cleaning.
These articles must be cleaned and dried sepa-
rately.
•Only use commercially available cleaning agents
with a pH value of 5-9.
•Observe the information on the mixing ratio.
•Allow the cleaning agent to soak in according to the
manufacturer's instructions.
•Remove the cleaning agent with warm water with-
out leaving any residues.
•Wipe the product with a damp cloth after cleaning.
•Dry the product with a cloth after cleaning. The
product may only be used when dry.
Exclusion:
Cleaning agents must not contain chlorine or
strong acids.
Do not use cleaners with abrasive additives.
Do not use high-pressure cleaners.
13.3 Disinfection
•The product is not intended for steam or hot air
sterilisation. Observe the temperature limits for use
(2.2).
•Only use surface disinfectants that have been
tested and approved by the Robert Koch Institute.
Agents based on (form)aldehyde or alcohol are
permissible.
•Observe material approvals of disinfectant manu-
facturers. The product consists of the following
components or materials:
Polyamide: Frame, armrests, footrests
Polyurethane: Seat, backrest, leg support,
headrest
Polypropylene: Bucket & holder
Polyethylene: Nameplate
Aluminium: Tubes
Stainless steel: Screws, washers. Nuts
•Observe the information on the mixing ratio.
•Observe the safety instructions of the disinfectant
manufacturer.
•Apply the disinfectant to the surface by spraying or
rubbing.
•Allow it to take effect. Observe the specified expo-
sure times.
•Depending on the disinfectant, subsequent wiping
with warm water may be necessary.
•Remove the disinfectant without leaving any resi-
dues.
Exclusion:
Do not use alcohol-based agents at the stickers
& nameplates.
Cleaning agents must not contain chlorine or
strong acids.

REBOTEC / BA-Nr.: 02.07.135/2023-05-A01
- 11 -
EN
14 Maintenance
•Wear and tear that is not recognised in time and/or
improper handling, as well as irregular or no
maintenance may result in accidents.
For safety reasons, the product must be pro-
fessionally maintained at least once a year.
•Regular safety checks are required:
Check the product and accessories for visible
damage (cracks, breaks, loose parts)
Check stability before use
All screw connections for tightness
Function of the armrests and locking bolts
Function of the footrest
Running characteristics and tread of the wheels
Function of the parking brakes
Function of the headrest
Function of the tilt adjustment
•If you have any questions concerning the mainte-
nance of the product, please contact an authorised
dealer or a medical and healthcare supplies store.
In the event of damage or repairs, contact your au-
thorised dealer immediately.
•Do not make any unauthorised changes to the
product. This may compromise its safety and
proper function. In such cases, REBOTEC will not
assume any liability.
•Only use OEM spare parts for repairs. See 15.
•After maintenance or repair work has been carried
out, we recommend you clean the product before
using it again.
•Please note section 15 and 7.
•Please observe the maintenance instructions
(02.11.151)
For documenting the maintenance and repair
work, REBOTEC provides a Maintenance Re-
port.The user manual and maintenance log
can be ordered or viewed via www.rebotec.de. It is
also possible to print the information and read it
when needed.

REBOTEC / BA-Nr.: 02.07.135/2023-05-A01
- 12 -
EN
15 Spare parts & accessories
No.
Art. no.
Designation
1a
301.00
Toilet bucket with lid
1b
302.00
Toilet bowl
2
309.10
Bucket holder
3
440.10.62
PUR lining mat for shower and toilet seat
4
440.10.14
PUR shower seat
5
440.10.24
PUR shower seat, closed
6
450.10.16
PUR backrest cushion
7
450.10.17
PUR Leg support
8
448.00.83
Front wheel (Phoenix)
9
448.00.81
Rear wheel (Phoenix)
10
443.00.91
Wheel (Phoenix 200)
-
450.10.58
PUR Headrest, standard
-
450.10.59
PUR headrest, comfort
-
440.10.32
PUR Arm support
-
440.10.40
PUR Splash protection
-
02.07.135
User manual
-
02.11.151
Maintenance log
Use only REBOTEC spare parts and accessories to ensure the proper and safe functioning of the
device.
1a
2
3
4
6
7
5
9
8
10
1a & b

REBOTEC / BA-Nr.: 02.07.135/2023-05-A01
- 13 -
EN
16 Drawing & dimensions
No.
Designation
Type PU
Type PS
Type 200 PU
Type 200 PS
a1
Overall height
1230 mm
a2
Overall height
1110 mm
a3
Handlebar height
1060 mm
b
Overall width
650 mm
675 mm
c1
Overall depth
1110 mm
c2
Overall depth
1435 mm
d
Seat height
570 mm
Seat width
450 mm
e
Width between armrests
540 mm
f
Seat depth
430 mm
g
Height to armrests
760 mm
h
Knee height of footrest min.
440 mm
Knee height of footrest max.
520 mm
i
Headrest height
120 mm
j1
Seat angle
103°
j2
Lying angle
128°
k
Front castor diameter
125 mm
Rear castor diameter
125 mm
Dimensions and weights may vary depending on the equipment. There might be minor deviations
due to production tolerances. Subject to change without notice.

REBOTEC / BA-Nr.: 02.07.135/2023-05-A01
- 14 -
EN

REBOTEC / BA-Nr.: 02.07.135/2023-05-A01
- 15 -
EN

REBOTEC / BA-Nr.: 02.07.135/2023-05-A01
Read this user manual before using the device for the first time and keep it at hand for the
user as well as for future use and subsequent sales.
EN
REBOTEC®
Rehabilitationsmittel GmbH
D-49610 Quakenbrück, Artlandstr. 57-59
Telephone: [phone]
Fax: [phone]
Web:
www.rebotec.de
Email:
[email protected]
EN