Reece Omnivo Neo User manual

NEO WALL HUNG VANITY UNIT
NEO BASIN INSTALLATION INSTRUCTIONS
No claims for damages / defects will be recognised after installation.
Prior to installation it is important to unpack and inspect your products to ensure no damage has
occurred in transit and that the product IS CORRECT.
If damage has occurred, or a visible defect exists, do not proceed with installation and contact supplier
IMMEDIATELY.
Step 1. Mark out bolt positions ensuring they are level and at the correct height.
Step 2. Installer to determine appropriate fixings, ensure wall is suitable and studs, noggins etc. are in
appropriate locations.
Step 3. Once appropriate fixings are in the wall, place basin over bolts and tighten.
See figure 1.
Step 4. Once basin is attached to wall, connect trap and other hardware as necessary.
Figure 1.
ASSEMBLY LIST
Neo basin
(purchased seperately)
Designer handle
Large drawer
Cabinet body
Dimensions are approximate. Information provided in this installation is a guide only. We recommend having the product on site prior to rough in.
Plumbers, please ensure a copy of the installation Instructions is left
with the end user for future reference
Adjustable shelf
Note: Neo Mini comes with pull down drawer and doesn’t include a shelf
Neo Mini basin
(purchased seperately)
Designer handle
Cabinet body
Note: Bottle trap is not included with basin
page 1 of 5

NEO CABINET INSTALLATION INSTRUCTIONS
No claims for damages / defects will be recognised after installation.
Prior to installation it is important to unpack and inspect your products to ensure no damage has
occurred in transit and that the product IS CORRECT.
If damage has occurred, or a visible defect exists, do not proceed with installation and contact supplier
IMMEDIATELY.
Step 1. Remove drawer and align cabinet directly under the already installed Neo basin.
See figure 2 and 3.
The Neo Mini cabinet has a pull down door not a removable drawer therefore you don’t have to remove
anything to install this particular cabinet on your wall.
NOTE: Often cabinets are made slightly smaller than the vanities so the basin can overhang the cabinet
sides. Ensure your basin is centred over the cabinet when installing.
Step 2. Installer to determine appropriate fixings and provide adequate wall framing (studs/nogging) to ensure
secure mounting of cabinet.
Step 3. If the wall is not level/square, packers must be used to prevent cabinet twisting/malfunction.
Step 4. As a minimum, use fixings at all corners and top and bottom centres. Use additional fixings if required.
All fixings must be secured to wall framing (studs/noggins). See figure 4.
Step 5. Insert the drawer by simply locating the runners and pushing it in. Ensure runners ‘click’ into location.
Test operation by opening and closing ensuring it’s secure to the cabinet.
NEO WALL HUNG VANITY UNIT
Figure 2.
Plumbers, please ensure a copy of the installation Instructions is left
with the end user for future reference
Figure 3.
page 2 of 5

NEO WALL HUNG VANITY UNIT
Figure 4.
Dimensions are approximate. Information provided in this installation is a guide only. We recommend having the product on site prior to rough in.
Plumbers, please ensure a copy of the installation Instructions is left
with the end user for future reference
Basin)
Trap not
supplied
page 3 of 5

Figure 5. Removing drawer
Remove drawer by pulling fully out
and then pull upward, holding the
underside front
1.
2.
Figure 6. Replacing drawer
± 2 mm ± 2 mm
2.
1.
Figure 7. Adjusting drawer front
Plumbers, please ensure a copy of the installation Instructions is left
with the end user for future reference
NEO WALL HUNG VANITY UNIT
NEO CABINET DRAWER ADJUSTMENT INSTRUCTIONS
page 4 of 5

Plumbers, please ensure a copy of the installation Instructions is left
with the end user for future reference
NEO WALL HUNG VANITY UNIT
Figure 8. Replacing drawer front
3. 4.
1.
2.
optional
step
NEO CABINET DRAWER ADJUSTMENT INSTRUCTIONS
page 5 of 5