Reece Posh Solus Installation guide

Posh Solus Heated Towel Rail - Plug-in or Hardwired
Operations and Maintenance
WARNING
This product must be installed by a qualified electrician in accordance with AS/NZS 3000 wiring rules. Switch off the electrical
supply at the mains before installation and maintenance. A means of disconnection must be incorporated in the fixed wiring
in accordance with the wiring rules. For complete temperature control a wall mounted dimmer switch (with “off” position) is
recommended. Suitable for bathroom and non-bathroom/dry areas. Not suitable for above baths, nor for installation in saunas,
steam rooms or shower cubicles. Please consult with a qualified electrician to confirm appropriate compliant installation
location.
Rated IP45 and suitable for indoor use only. Do not fix to damp or conductive surfaces. Site well away from curtains and fabrics.
Switch off after use.
This appliance is not to be used by persons (including children) with reduced physical, sensory or mental capabilities, or lack
of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a
person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
WARNING: In order to avoid a hazard for very young children, this appliance should be installed so that the lowest heated rail
is at least 600mm above the floor.
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified person in order
to avoid a hazard.
For safety, please DO NOT use for any purpose other than as a towel rail and a towel warmer. To avoid damage DO NOT sit,
stand, lean or hang on product.
OPERATION AND MAINTENANCE
• After installation, connect the electric power and turn on the wall switch. The towel warmer will start to work.
• Turn off the power wall switch when towel warmer is not in use.
• Clean the towel warmer with a soft dry towel.
• This unit has been designed to run continuously
The surface temperature is high when towel warmer operates. PLEASE BE CAREFUL!
ELECTRICAL INSTALLATION
Please ensure this towel warmer is installed by a registered electrician and ensure the electrical supply, plug
& switch location and product location will comply with your local regulations.
This appliance must be fitted with an air gap phase isolation switch. For complete temperature
control, a wall mounted dimmer switch (with “off” position) is recommended. Please consult with a
qualified electrician for selection of an appropriate device.

Posh Solus Heated Towel Rail - Plug-in or Hardwired
• Use the fixing point distances provided to
mark out the fixing points.
• Before drilling, check that the product
aligns to the marked fixing points and make
adjustments if necessary.
• Note: Wall materials vary. The fixing kit
supplied is suited for solid wall fixing. For
timber framed walls, please ensure the
product is fixed to a stud/noggin behind the
wall. Where a stud/noggin is not avilable,
please use suitable hollow wall fixing.
INSTALLATION INSTRUCTIONS
Please consult with a qualified electrician to confirm appropriate compliant installation location.
Installation Instructions
Plug-in Installation
*generic product image used

Posh Solus Heated Towel Rail - Plug-in or Hardwired
• With the allen key provided, tighten the grub
screws to ensure that towel rail stays in position.
Installation Instructions
Electrician, please ensure a copy of the installation
instructions is left with the end user for future reference
Hardwired Installation
• Use the fixing point distances provided to
mark out the fixing points.
• Before drilling, check that the product
aligns to the marked fixing points and make
adjustments if necessary.
• Note: Wall materials vary. The fixing kit
supplied is suited for solid wall fixing. For
timber framed walls, please ensure the
product is fixed to a stud/noggin behind the
wall. Where a stud/noggin is not avilable,
please use suitable hollow wall fixing.

Posh Solus Heated Towel Rail - Plug-in or Hardwired
• Cut the power cord and connect to the
power supply.
Installation Instructions
• With the allen key provided, tighten the grub
screws to ensure that towel rail stays in position.