Reece Posh Domaine MK2 User manual

Posh Domaine MK2 Shower Base
Posh Domaine MK2 Shower Base
Specification Sheet
Posh Solus MK2 Towel Rack Chrome
9506583
TBA
Cartridge Sleeve x1 Anchor x4 Screw x4
A B C D E F
H I
Mixer Body x1
Tools Required
Drill
Wrench
Test Plug x1 Cartridge Tile Cover x1
Cartridge Complete x1 Push In Connector x1
Allen Key
TBA
TBA
Installation Instructions
Posh Domaine MK2 Shower Base
Page 1 of 2
Plumbers, please ensure a copy of the Installation
Instructions are left with the end user for future reference
ŸAny boxed opening in the slab to accommodate the waste must not
exceed 300mm in width beneath the shower base.
ŸShower Base to be fixed to floor by spreading cement-based tile
adhesive on the floor using a 12mm notched trowel, or by use of
silicone sealant. Alternatively, where the floor is not perfectly level,
the base can be set into a mortar bed - spread a 10mm thick mortar
bed of 4:1 Washed Sand: Spread the mortar over the whole area
where base is to be installed then trowel off level.
Do not use “Liquid Nails” or similar rigid construction-
type adhesive to install base.
ŸLay the shower base on the prepared bed and use a sprit level to
adjust the base to ensure it is level along all sides and diagonally.
This will allow the base to drain properly as it has an inbuilt fall to the
waste outlet.
ŸBackfill the opening the slab with a 4:1 Washed Sand: Cement mix
ensuring the mortar is packed tightly around the waste outlet and all
the way back into the boxed section of the slab and up to the
underside of the base to give maximum support.
Note: Where required by regulation plastic pie and fittings may
need to be lagged prior to backfilling.
At this point it is imperative to check that water drains to
the waste outlet prior to lining the shower walls (see
Smartpan/ Smartwaste). Failure to do so is a breach of
warranty.
ŸWhen the installation uses these product as the waste collectors,
ensure that the lid/cover is fitted to provide adequate support for the
base. Cut a hole in the lid/cover the same size as the waste.
Ÿ
It is recommended installation practice to check the edge of the base
into the wall by the width of the tiling flange in order to achieve a leakfree
junction with the wall cladding material (see diagram ‘A’).
Pre-Installation Note
Timber Floor
Floor boards or sheet flooring must cover the entire underside of the base.
Cut a hole for waste no greater than 120x120mm.
Note: If renovating, ensure the floor is structurally sound. Replace
the floor if necessary.
Shower base to be fixed to floor by spreading cement-based tile adhesive
on the floor using a 12mm notched trowel or by use of silicone sealant.
Alternatively, where the floor is not perfectly level, the base can be set into
a mortar bed - spread a 10mm thick mortar bed of 4:1 Washed Sand:
Spread the mortar over the whole area where base is to be installed then
trowel off level.
Lay the shower base on the prepared bed and use a spirit level to adjust
the base to ensure it is level along all sides and diagonally. This will allow
the base to drain properly as it has an inbuilt fall to the waste outlet.
Concrete Slab
Any boxed opening in the slab to accommodate the waste, must not
exceed 300mm in width beneath the shower base.
Shower base to be fixed to floor by spreading cement-based tile adhesive
on the floor using a 12mm notched trowel, or by use of silicone sealant.
Alternatively, where the floor is not perfectly level, the base can be set into
a mortar bed - spread a 10mm thick mortar bed of 4:1 Washed Sand:
Spread the mortar over the whole area where base is to be installed then
trowel off level.
Lay the shower base on the prepared bed and use a spirit level to adjust
the base to ensure it is level along all sides and diagonally. This will
allow the base to drain properly as it has an inbuilt fall to the waste
outlet.
Backfill the opening in the slab with a 4:1 Washed Sand: Cement mix
ensuring the mortar is packed tightly around the waste outlet and all the
way back into the boxed section of the slab and up to the underside of the
base to give maximum support.
Note: Where required by regulation plastic pie and fittings may need
to be lagged prior to backfilling.
Smartpan/Smartwaste
When the installation uses this product as a waste collector, ensure that
the lid/cover is fitted to provide adequate support for the base (see
diagram ‘E’).

Posh Domaine MK2 Shower Base
Flush out new pipe work prior to connecting the new
mixer.
During installation, protect the exposed surface finish by
using the plastic covers provided.
In a typical installation, the mixer is mounted on a
timber/metal noggin and secured using suitable screws
through the mounting lugs.
For wall mounted Basin Tapware, consideration should
be made to installation height and length of outlet in
relation to height and positioning of basin on bench top.
Leaking joints are not covered by the warranty.
Leaking joints are not covered by the warranty.
Page 2 of 2
Installation Instructions
Posh Domaine MK2 Shower Base
Page 2 of 2
Installation Instructions
Posh Domaine MKII Shower Base
SMART PAN / TRAP
CLEANING
-
Avoid All Forms of Abrasion
-
WARRANTY
.
Warning
STORAGE
SMART TRAP / PAN LID MUST
REMAIN
ON IF USED UNDER SHOWER BASE
CUT HOLE IN LID OF SMART TRAP / PAN
THEN ALIGN WASTE FOR BASE SO THAT
IT FEEDS THROUGH HOLE IN LID
Plumbers, please ensure a copy of the Installation
Instructions are left with the end user for future reference
Plumbers, please ensure a copy of the Installation
Instructions are left with the end user for future reference
Installation Instructions
Posh Domaine MK2 Shower Base
Installation Instructions
Posh Domaine MKII Shower Base
SMART PAN / TRAP
CLEANING
WARRANTY
Warning
STORAGE
SMART TRAP / PAN LID MUST
REMAIN
ON IF USED UNDER SHOWER BASE
CUT HOLE IN LID OF SMART TRAP / PAN
THEN ALIGN WASTE FOR BASE SO THAT
IT FEEDS THROUGH HOLE IN LID
Page 2 of 2
Installation Instructions
Posh Domaine MK2 Shower Base
Page 2 of 2
Installation Instructions
Posh Domaine MKII Shower Base
SMART PAN / TRAP
CLEANING
-
Avoid All Forms of Abrasion
-
WARRANTY
.
Warning
STORAGE
SMART TRAP / PAN LID MUST
REMAIN
ON IF USED UNDER SHOWER BASE
CUT HOLE IN LID OF SMART TRAP / PAN
THEN ALIGN WASTE FOR BASE SO THAT
IT FEEDS THROUGH HOLE IN LID
Plumbers, please ensure a copy of the Installation
Instructions are left with the end user for future reference
Plumbers, please ensure a copy of the Installation
Instructions are left with the end user for future reference
Page 2 of 2
Plumbers, please ensure a copy of the Installation
Instructions are left with the end user for future reference
Important to both installation types when using a smart pan or a smart
trap, the lid needs to be cut out to the size of the waste outlet (not
removed) and repositioned over the opening. This lid support is required.
Failure to follow this instruction will void warranty for the shower base
(see diagram).
The surface of this base will resist surface build-up. However, to preserve
it’s high luster it may be cleaned with a soft cloth using warm soapy water
or household detergent.
Avoid All Forms of Abrasion.
If accidental abrasion occurs, the surface brilliance can be restored by
polishing with a silicone-based polish.
Posh Domaine MK2 shower bases are made of solid synthetic
polymarble. Shower bases are guaranteed for 7 years against faulty
materials or workmanship, subject to warranty terms and conditions.
Warranty will be void if temperature from tap exceeds 55°C and above
instructions are not adhered to exactly.
Shower bases can distort if not stored correctly. If not installed
immediately, the shower base must be stored upright, flat, fully supported,
not leaning on waste outlet and not exposed to temperatures exceeding
55°C. Distortion occurred due to incorrect storage is not covered by
warranty. The shower base must be tested for correct draining prior to
installation.
Published 21/10/2022