ReelCraft 5400 OLP Use and care manual

Installation: A flexible hose connection must be used between the hose reel inlet and the source of supply to prevent
possible misalignment and binding.
Mounting: The hose reel is equipped with a universal mounting bracket so that it can be mounted on the floor, wall or
ceiling; whichever place is convenient. The hose guide arm can be moved to the position desired by removing
the screws fastening the guide bracket to the reel base. Shift the guide arm bracket so the hose comes off the
reel at the desired position and replace the screws.
Lubrication: Hose reel spring and bearings are factory lubricated and require no further lubrication.
Replacing
Hose:
1. Wind spool flange clockwise-facing swivel-until spring is tight.
2. Back off three turns and latch.
3. Insert hose through roller guide and hole in spool flange.
4. Connect hose fitting to swivel joint and secure hose with clamps.
Adjustments: To adjust spring tension, add or remove wraps of hose from the spool, one wrap at a time until desired tension
is obtained.
Repairs:
II.
Safety
I.
Remove all spring tension before beginning
disassembly process.
Do not use reels at higher pressures or
temperatures than listed on the back of this
bulletin.
FORM NO: 489-884
REV: 3/2009
Extensive repairs should be performed only by an authorized serviceman or factory to avoid damage which may
void your warranty. Remove all spring tension before beginning disassembly process.
Instructions
Four 5/16" Mounting holes.
Reelcraft Industries, Inc. • [phone] / [phone] • Fax: [phone]
E-mail: [email protected] • Internet: www.reelcraft.com
A14 1/2”
B13 3/4”
C9 3/4”
D2 1/2”
E6”
Hose Reel
Operating Instructions and Parts List
Low Pressure Models
5400 OLP 5600 OLP
5440 OLP 5630 OLP
5450 OLP 5635 OLP

Reelcraft Industries, Inc. • [phone] / [phone] • Fax: [phone]
E-mail: [email protected] • Internet: www.reelcraft.com
Item # Part # # Req. Description Item # Part # # Req. Description Item # Part # # Req. Description
1S600886 1Swivel Assembly 13 500101 1Base Assembly 24 300001 510-32 x 3/8” Screw
2300031 21” Snap Ring 14 300011 710-32 Hex Lock Nut 25 400020 1O-ring
3300034 2Spacing Washer 16 S261360 1Spring Case Stud 26 S400109 1Latch Plate Assembly
4S295-102 31/4” Plastite Hex Screw 17 300006 13/8-16 x 1/2” Set Screw 27 300035 110-32 x 1” Mach. Screw
5260022 1Sheave Flange 18 500103 1Spring Case Assembly 29 261650-1 21/4-20 Zinc Nyloc Nut
6500006 1Sheave Disk 19 S82-15 110-32 x 3/8” Nyloc Nut 30 S400015 1Main Shaft
7S500019 1Latch Cam 20 S400021 1Latch Bumper
8S260648 1Spring Arbor 21 S32-136 110-24 x 3/8” Mach. Screw
9300002 210-32 x 1/2” Screw 22 S400012 1Latch Bushing
12 500107 1Guide Arm & Roller Assembly 23 S400018 1Latch Spring
Item # Description # Req. Model
5400 OLP
Model
5440 OLP
Model
5450 OLP
Model
5600 OLP
Model
5630 OLP
Model
5635 OLP
10 Hose Bumper Assembly 1None 1-HR1004A 1-HR1004A None 1-HR1004 1-HR1004
11 Hose Assembly 1None 601000-40 601000-50 None S601011-30 S601013-35
15 Drive Spring Assembly 1S503755 S503755 S503755 S504240 S504240 S504240
28 U-Bolt 13-117440 3-117440 3-117440 3-117440 3-117440 3-117440
Hose I.D. and Length None 1/4” x 40’ 1/4” x 50’ None 3/8” x 30’ 3/8” x 35’
Reel Inlet Connection 3/8” F.P.T. 3/8” F.P.T. 3/8” F.P.T. 3/8” F.P.T. 3/8” F.P.T. 3/8” F.P.T.
Max. Operating Pressure 500 P.S.I. 300 P.S.I. 300 P.S.I. 500 P.S.I. 300 P.S.I. 300 P.S.I.
Max. Operating Temperature 210° F 150° F 150° F 210° F 150° F 150° F