ReelCraft 3700 Series User manual

Hose Reel Operations Manual
IMPORTANT
Read this manual carefully before installing,
operating or servicing this equipment.
PERSONAL SAFETY
Personal injury and/or equipment damage may result
if proper safety precautions are not observed.
ORDER #:
MODEL #:
SERIAL #:
WARNING: Even low pressure can
cause irreparable damage or death.
Exercise extreme caution while
operating or servicing this equipment.
3700 SERIES
Reelcraft Industries, Inc. • 2842 E Business Hwy 30, Columbia City, IN 46725
Ph: 800-444-3134 / 260-248-8188 • Fax: [phone]
Customer Service: 855-634-9109 • [email protected] • www.reelcraft.com
Item # Description Quantity Item # Description Quantity Item # Description Quantity
1 FRAME WELDMENT ASSEMBLY 1 14 HANDWIND ASSEMBLY 1 27 S338-6 HEX NUT 3/8”-16 UNC 26
2 BEARING HOUSING SUB ASSEMBLY 1 15 CRANK AND HANDLE ASSEMBLY 1 28 S347-65 HEX CAP SCREW 3/8”-16 UNC X 1” 19
3 PAT1075AL CASTING BEARING SPACER 1 16 TIE ROD 6 29
S347-611 HEX CAP SCREW 3/8”-16 UNC X 2.5” 2
4 PILLOW BLOCK ASSEMBLY 1 17 HEAD INSERT 1 30
S347-66 HEX CAP SCREW 3/8”-16 UNC X 1.25” 10
5 SPINDLE 1 18 MOTOR 1 31 S347-616 HEX CAP SCREW 3/8”-16 X 3.75” 2
6 SUPPORT SHAFT 1 19 DRUM 1 32 CHAIN GUARD 1
7 HEAD 2 20
GOOSENECK 1 33 S350-41 WASHER SMALL 3/8” 2
8 S390030-1 SPACER 3/8” X 7/16” LG 4 21
IDLER ASSEMBLY / or CLUTCH ASSEMBLY 1 34 S347-610 HEX CAP SCREW 3/8”-16 UNC X 2.25” 2
9 S338-5 HEX NUT 4 22 SPROCKET, MOTOR 1 35 S376-59 HEX CAP SCREW (5/16-18 X 2) 1
10 S390030-3 SPACER 3/8” X 3/4” LG 4 23
JUNCTION BOX ASSEMBLY (OPTIONAL) 1 36 S85-7 NYLOC NUT (5/16-18) 1
11 SPROCKET, LARGE 1 24 S347-69 HEX CAP SCREW 3/8”-16 UNC X 2” 10 37 SEAL AND RING ASSEMBLY 1
12 INLET 1 25 S350-6 WASHER 3/8” 56 38 SNAP RING 1
13 GEAR, BEVEL 1 26 S339-616 LOCK WASHER 3/8” 30

PRE-INSPECTION
1. Check reel for shipping damages.
2. Insured all parts are supplied as ordered.
3. Record model number and serial number for future refer-
ence.
MOUNTING
1. Unpack and inspect reel - rotating spool (1) to check for
smooth operation.
2. Ensure that mounting surface is rigid and flat to prevent
binding of reel after it is installed. This is important to en-
sure proper alignment.
3. Drill four mounting holes in reel frame. Secure reel to
mounting surface by inserting four bolts (2) through the
four mounting holes (3) just drilled into the reel frame.
Tighten securely to ensure a solid, rigid attachment.
Hose Reel Operations Manual
Page 2 www.reelcraft.com
• Ensure that reel is properly installed before connecting supply line (see instructions).
• Before connecting supply line to reel, ensure that supply line pressure does not exceed maximum rated working pressure of the
reel.
• Do not wear loose fitting clothing while operating reel.
• Be aware of other personnel / machinery in work area.
• If a leak occurs in hose or reel, remove supply line pressure immediately.
• Treat and respect a hose reel as any other piece of machinery, observing all common safety practices.
PERSONAL SAFETY
• Pull hose by grasping the hose itself not by the control valve swivel.
• When working around flammable liquids such as solvents, paints, chemicals or petroleum products, ensure that the hose reel
and the equipment being serviced is properly grounded. Use a grounding hose (static wire).
• Use an ohmmeter to check continuity of the grounding circuit. Fire and/or explosion can result if proper grounding is not
achieved.
• If reel is electric, air or hydraulic driven, be careful of chain / sprocket drive system. Keep hands clear and do not wear loose
fitting clothing while operating reel.
• If reel ceases to unwind or rewind properly, remove power immediately. Do not pull or jerk on hose. Find and remedy problem
before continuing.
WARNINGS & TIPS
Prevent static sparking
1. Ensure that all supply and motor electrical ratings are compat-
ible.
2. Wire power to the motor following applicable wiring diagram.
3. Switch reel on to insure proper wiring procedures were fol-
lowed. Check alignment of heads, motor, chain and sprocket
while the hose reel turns.
ELECTRIC DRIVEN REELS
WARNING: Remove all electrical power when wiring. DO NOT
“HOT WIRE”. Observe all applicable NEC, OSHA, and local codes.
NOTE: It is not proper to connect either power lead to any part of
the motor, or to any part attached to the motor, such as the
terminal box, as that would make the motor an integral part of the
electrical power circuit.

Hose Reel Operations Manual
www.reelcraft.com Page 3
AIR DRIVEN REELS
1. Apply thread compound to
inlet air line fitting (1) and
pneumatic motor (2) inlet
threads.
2. Connect inlet air line
(1) to motor (2).
HYDRAULIC DRIVEN REELS
1. Apply thread compound inlet / outlet hydraulic line fittings
(1) and hydraulic motor inlet threads (2).
2. Thread hydraulic line fittings (1) into motor inlet / outlet (2)
tighten securely.
INLET CONNECTION
NOTE: Install a union fitting as near as possible to the swivel
joint inlet, so the joint can be easily removed for servicing.
CONNECTING THE SUPPLY LINE FOR THREADED INLET
SWIVELS
NOTE: Avoid strain on swing joint at all times. Threaded type
swivel inlets must be connected to the fluid supply by using a
flexible connector.
1. Apply thread compound to the swivel (1) and connecting
hose fitting (2) threads.
2. Thread connecting hose fitting (2) into swivel (1). Tighten
securely.
3. With control valve open, fully extend and charge hose
to purge system of gases. When fluid appears at control
valve, close valve. This prevents flattening of hose and ex-
cessive pressure on drum when fluid supply is reinitialized
at a later time.
GROOVED INLET SWIVELS
NOTE: Grooved type swivel joint inlet connections must be
carefully aligned. Two grooved connections, correctly installed,
allow adequate flexibility for smooth rotation.
1. Connect grooved coupling onto inlet swivel fitting and inlet
supply line
2. Adjust inlet supply line to verify flexibility exists for proper
alignment.
3. With control valve open, fully extend and charge hose
to purge system of gases. When fluid appears at control
valve, close valve. This prevents flattening of hose and ex-
cessive presure on drum when fluid supply is reinitialized
at a later time.
GROOVED
CONNECTION FLEXIBLE CONNECTION
NOTE: Failure to
use flexible con-
nector with any
live reel will void
warranty
For larger reels, gooseneck may be removed from reel to fit to
hose. Note that if the reel has a welded or threaded riser in the
fluid path assembly, it cannot be removed to attach the hose.
CAUTION: Do not connect the output hose to the gooseneck
(1) until after the reel is installed and motor connections are
complete. Fill the hose before winding on the reel to prevent
excessive pressure on the drum when hose is filled.
1. Apply thread compound
to connecting gooseneck
(1) and output hose fitting
threads (2).
2. Hand thread output hose
fi tting (2) into gooseneck
(1).
3. Using a wrench, fi rmly
hold gooseneck (1) while
tightening out put hose fit-
ting (2).

Hose Reel Operations Manual
Page 4 www.reelcraft.com
REPLACE THE SWIVEL
CAUTION: Remove supply line
pressure before performing the
following procedures.
1. Remove supply line (2)
from the swivel (1) or
inlet.
2. Remove swivel (1) from
inlet shaft (3).
3. Install replacement swivel
by reversing steps 1 & 2.
REPLACING “U” CUP SEALS ON NORDIC SWIVELS
NOTE: For special swivels such as food grade, Catherine style reels,
and special purpose swivels, see attached exploded drawing and
parts list for special instructions for swivel repair / replacement.
1. Remove supply line (3) from inlet adaptor (1).
2. Remove all three bolts (2).
3. Pull seal from recess inside of inlet adaptor.
4. Examine new seal (5) and ring (4) to check for damage.
5. Moisten face of seal with lubricant and replace into inlet adaptor
(1).
6. Bolt adaptor back in place and re-install supply line.
REPLACING THE MOTOR
CAUTION: Before replacing the motor, remove electrical power and
fluid pressure from reel.
1. Loosen (do not remove) bolts (1) securing motor (2) to reel.
2. Slide motor and remove chain.
3. Remove bolts securing motor.
4. Install replacement motor.
REPLACING THE CHAIN
CAUTION: Before replacing the chain, remove electrical
power and fluid pressure from reel.
1. Loosen (do not remove bolts securing motor (2) to reel.
2. Remove chain master-link.
3. Install replacement chain (1).
4. Adjust chain tension by moving motor until properly
obtained. Over tensioning results in reduced motor life.
Adjust to allow between ¼” and ½” play in chain.
HOW TO ORDER REPLACEMENT PARTS
Please provide the following information:
1. Model number
2. Serial number
3. Part description and/or balloon number listed on the
front of this manual.
*Some parts may not be shown, in this case a detailed part
description will be required.