ReelCraft 5005 Series User manual

1. Do not use reel at higher pressures or temperatures than listed on
the back of this bulletin.
2. Remove all spring tension before beginning dissassembly process.
SAFETY
5605 OLP 5605 OMP 5405 OHP
5650 OLP 5435 OHP
Operating Instructions
Series 5005 Spring Driven Hose Reels
Low, Medium and High Pressure Model Numbers:
Dimensions
A17 5/8”
B16 1/2”
C9 3/4”
D2 1/2”
E5 7/8”
INSTALLATION: A flexible hose connection must be used between the hose reel inlet and the source of supply to prevent possible
misalignment and binding.
LUBRICATION: Hose reel spring and bearings are factory lubricated and require no further lubrication.
REPLACING HOSE: 1. Wind spool flange clockwise-facing swivel-until spring is tight.
2. Back off three turns and latch.
3. Insert hose through roller guide.
4. Connect hose fitting to swivel joint and secure hose with clamps.
ADJUSTMENTS: To adjust spring tension, add or remove wraps of hose from the spool, one wrap at a time until desired tension is
obtained.
REPAIRS: Extensive repairs should be performed only by an authorized serviceman or factory to avoid damage which may
void your warranty. Remove all spring tension before beginning disassembly process.
MOUNTING: The hose reel is equipped with a universal mounting bracket so that it can be mounted on the floor, wall or
ceiling; whichever place is convenient. The hose guide arm can be moved to the position desired by removing
the screws fastening the guide bracket to the reel base. Shift the guide arm bracket so the hose comes off the
reel at the desired position and replace the screws. NOTE: For proper installation in wall mount applications, ensure
reel is mounted with inlet on the right as you are facing the reel. Failing to do so could cause latching issues.

Series 5005 Spring Driven Hose Reels
Page 2
9
8
7
6
5
10 30 12
13
30
14
15
16
17
18
19
20
21
30
22
24
25
27
26
27
28
29
1
2
3
4
Item # Description # Req. 5605 OLP 5650 OLP 5605 OMP 5405 OHP 5435 OHP
8Bumper Stop Assembly 1 None 1-HR1004 None None 1-HR1004
9 Hose Assembly 1 None S601013-50 None None 20-260044
15 Drive Spring Assembly 1 S600050 S600050 S600050 S600050 600020
25 Main Shaft 1 602555 602555 602305 602306 602306
26 Swivel & Ell Assembly 1 None None S600358 S260492 S260492
27 90° Elbow 1 None None S257-72 S257-10 S257-10
28 90° Elbow 1 None None S257-25 None None
29 Swivel Assembly 1 S600886 S600886 602032 S260042 S260042
Hose I.D. and Length None 3/8” x 50’ None None 1/4” x 35’
Reel Inlet Connection 3/8” F.P.T. 3/8” F.P.T. 3/8” F.P.T. 1/4” F.P.T. 1/4” F.P.T.
Max. Operating Pressure 500 P.S.I. 300 P.S.I. 3000 P.S.I. 5000 P.S.I. 5000 P.S.I.
Max. Operating Temperature 210 °F 150 °F 210 °F 210 °F 210 °F
Item # Part # # Req. Description Item # Part # # Req. Description Item # Part # # Req. Description
1 300031 2 1” Snap Ring 10 S500107 1 Guide Arm Assembly 19 S400018 1 Latch Spring
2 300034 2 Spacing Washer 12 S261360 1 Spring Case Stud 20 400020 1 O-ring
3 S295-102 3 Hex Screw 13 300006 1 3/8-16 x 1/2” Set Screw 21 S400109 1 Latch Plate Assembly
4 260149 1 Reel Flange 14 S600094 1 Spring Case & Hub Assembly 22 2-117440 1 U-Bolt Hose Clamp
5 260151 1 Sheave Disk 16 600029 1 Base Assembly 24 261650-1 2 1/4-20 Nylock Nut
6 S500019 1 Latch Cam 17 S400021 1 Latch Bumper 30 S82-15 9 Nyloc Nut 10-32 x 3/8”
7 S260648 1 Spring Arbor 18 S400012 1 Latch Bushing
Learn more about air tools and compressors on our website.