resideo VISTA-50P User manual

VISTA-50P/VISTA-50PUL
Commercial Burglary
Partitioned Security System
With Scheduling
User Guide
N5943-6V2C 5/04 Rev C

– 2 –
IMPORTANT!
PROPER INTRUSION PROTECTION
For proper intrusion coverage, sensors should be located at every possible point of entry to a home or
commercial premises. This would include any skylights that may be present, and the upper windows in
a multi-level building.
In addition, we recommend that radio backup be used in a security system so that alarm signals can
still be sent to the Central Monitoring Station in the event that the telephone lines are out of order
(alarm signals are normally sent over the phone lines).
EARLY WARNING FIRE DETECTION
Early warning fire detection is important in a home. Smoke and heat detectors have played a key role
in reducing fire deaths in the United States. With regard to the number and placement of smoke/heat
detectors, we subscribe to the recommendations contained in the National Fire Protection Association's
National Fire Alarm Code (NFPA 72). These recommendations can be found on page 53 of this
manual.
SYSTEM COMPATIBILITY NOTICE
Your Resideo security system is designed for use with devices manufactured or approved
by Resideo for use with your security system. Your Resideo security system is not designed
for use with any device that may be attached to your security system's keypad or other
communicating bus if Resideo has not approved such device for use with your security
system. Use of any such unauthorized device may cause damage or compromise the
performance of your security system and affect the validity of your Resideo limited warranty.
When you purchase devices that have been manufactured or approved by Resideo, you
acquire the assurance that these devices have been thoroughly tested to ensure optimum
performance when used with your Resideo security system.

– 3 –
TABLE OF CONTENTS
SYSTEM OVERVIEW .........................................5
General ..............................................................5
A Partitioned System.........................................5
Zones .................................................................5
Fire Protection ...................................................6
Burglary Protection ...........................................6
Alarms ...............................................................6
Memory of Alarm..............................................6
Speed Key (Macros)..........................................7
Using Schedules ................................................7
Device Timers ...................................................7
To Access another Partition (GOTO
Command).........................................................7
Master Keypad Operation..................................8
Self-Help Feature ..............................................8
Phone Access & Voice Response
Capability ..........................................................8
ABOUT THE KEYPADS .....................................9
General ..............................................................9
The Alpha Keypad.............................................9
FUNCTIONS OF THE KEYPAD.......................10
FUNCTIONS OF THE KEYPAD
(CONT’D) .......................................................11
FUNCTIONS OF THE KEYPAD
(CONT’D) .......................................................12
ENTRY/EXIT DELAYS.....................................13
General Information ........................................13
SECURITY CODES AND AUTHORITY
LEVELS ..........................................................14
General Information ........................................14
Duress Code ....................................................14
Quick Arming..................................................14
SECURITY CODES AND AUTHORITY
LEVELS (CONT’D) .......................................15
Authority Levels..............................................15
SECURITY CODES AND AUTHORITY
LEVELS (CONT’D) .......................................16
General Rules on Authority Levels and
Changes ...........................................................16
To Exit User Edit Mode ..................................16
SECURITY CODES AND AUTHORITY
LEVELS (CONT’D)....................................... 17
To Add a User ................................................ 17
SECURITY CODES AND AUTHORITY
LEVELS (CONT’D)....................................... 18
SECURITY CODES AND AUTHORITY
LEVELS (CONT’D)....................................... 19
To Change a User's Code................................ 19
To Delete a User............................................. 19
ACCESSING OTHER PARTITIONS................ 20
To Access another Partition............................ 20
Global Arming................................................ 20
Master Keypad Operation............................... 22
ACCESSING OTHER PARTITIONS
(CONT’D) ...................................................... 23
Common Lobby Operation............................. 23
ACCESSING OTHER PARTITIONS
(CONT’D) ...................................................... 24
How User Codes Affect the Common
Lobby.............................................................. 24
CHECKING FOR OPEN ZONES...................... 25
Using the *READY Key ........................... 25
DISPLAYING ALL ZONE DESCRIPTORS .... 26
Using the *READY Key ........................... 26
BYPASSING PROTECTION ZONES .............. 27
Using the 6 BYPASS Key ......................... 27
Quick Bypass.................................................. 28
Displaying Bypassed Zones............................ 28
ARMING PERIMETER ONLY......................... 29
(WITH ENTRY DELAY ON)............................ 29
Using the 3 STAY key .............................. 29
ARMING PERIMETER ONLY......................... 30
ARMING PERIMETER ONLY......................... 30
Using the 7 INSTANT Key....................... 30
ARMING ALL PROTECTION ......................... 31
Using the 2 AWAY Key............................ 31
ARMING ALL PROTECTION ......................... 32

– 4 –
Using the 4 MAXIMUM Key ....................32
DISARMING AND SILENCING ALARMS .....33
Using the 1 OFF Key .................................33
Memory of Alarm ...........................................33
USING THE KEYSWITCH ...............................34
General............................................................34
Arming ............................................................34
Disarming........................................................34
CHIME MODE ...................................................35
Using the 9 Key .........................................35
VIEWING ALARM COMPANY
MESSAGES....................................................36
General Information ........................................36
PANIC KEYS .....................................................37
(FOR MANUALLY ACTIVATING
SILENT AND/OR AUDIBLE ALARMS) .....37
Using Panic Keys ............................................37
SPEED KEY (MACROS)...................................37
General Information ........................................38
Defining ..........................................................38
Executing ........................................................39
ACCESS DOOR CONTROL..............................40
General Information ........................................40
Executing ........................................................40
USING #70 RELAY MENU MODE ..................41
General Information ........................................41
USING SCHEDULES ........................................42
Delaying the Closing Time .............................42
Temporary Open/Close Schedules ..................42
USING SCHEDULES (CONT’D)......................43
Programming Temporary Schedules...............43
USING SCHEDULES (CONT’D)......................44
PROGRAMMING DEVICE TIMERS ...............45
General Information ........................................45
PROGRAMMING DEVICE TIMERS
(CONT’D) .......................................................46
EVENT LOG PROCEDURES............................47
General Information ........................................47
To Display the Event Log ...............................47
EVENT LOG PROCEDURES
(CONTINUED)...............................................47
TESTING THE SYSTEM (TO BE
CONDUCTED WEEKLY) .............................49
Using the 5 TEST Key ...............................49
Testing Your System.......................................49
FIRE ALARM SYSTEM ....................................50
In Case Of Fire Alarm.....................................50
Silencing a Fire Alarm ....................................50
Typical Trouble Displays ................................51
Power Failure ..................................................52
Non-Alpha Keypad Displays...........................52
Recommendations for Smoke and Heat
Detectors .........................................................53
Recommendations for Proper Intrusion
Protection ........................................................54
EMERGENCY EVACUATION .........................55
MAINTAINING YOUR SYSTEM.....................56
Taking Care of Your System...........................56
Replacing Batteries in Wireless Sensors .........56
Silencing Low Battery Warning Tones at
the Keypad ......................................................57
Routine Care....................................................57
QUICK GUIDE TO SYSTEM FUNCTIONS.....58
SUMMARY OF AUDIBLE
NOTIFICATION.............................................60
INDEX ................................................................65

– 5 –
System Overview
General
Your Resideo security system consists of a main control panel, at least one keypad,
and various sensors strategically positioned throughout the premises. The system
offers you three forms of protection: burglary, fire and emergency. The keypad
provides full control of system operation.
The system uses microcomputer technology to monitor all protection zones and
system status and provides appropriate information for display on the keypad(s)
used with the system, and initiates appropriate alarms. Your system may also have
been programmed to automatically transmit alarm or status messages over the
phone lines to a central alarm monitoring station.
This manual is designed to help you become comfortable operating your
system. Each function is explained in step-by-step detail. We recommend you
read the SYSTEM OVERVIEW section to become familiar with the terminology
and the basic features of the system.
A Partitioned System
Simply stated, a partitioned system shares one physical alarm system among
different users, each with their own requirements. For the most part, you as a user
need not know about other users and their structure in the system, but from time to
time, you may see display messages that indicate the system is in use by another
user. Do not be concerned, this is normal. Refer to the ACCESSING OTHER
PARTITIONS section for additional information.
Zones
Your system's sensing devices have been assigned to various "zones." For example,
the sensing device on your Entry/Exit door may have been assigned to zone 01,
sensing devices on windows in the master bedroom to zone 02, and so on. These
numbers will appear on the display, along with an alpha descriptor for that zone (if
programmed), when a fault, alarm or trouble condition occurs.

– 6 –
System Overview (cont’d)
Fire Protection
The fire protection portion of your security system (if used) is always on and will
sound an alarm if a fire condition is detected. Refer to the FIRE ALARM SYSTEM
section for important information concerning fire protection, smoke detectors and
planning emergency exit routes from your house.
Burglary Protection
The burglary protection portion of your system must be turned on or "armed"
before it will sense burglary alarm conditions. Your system provides four modes of
burglary protection: STAY, AWAY, INSTANT and MAXIMUM, and even allows you to
BYPASS selected zones of protection while leaving the rest of the system armed. The
system also provides a CHIME mode, for alerting users to the opening and closing of
doors and windows while the system is disarmed. Refer to the other sections of this
manual for procedures for using these features.
The following table lists the four different arming modes and the results of each.
Features For Each Arming Mode
Arming Mode
Exit
Delay
Entry
Delay
Perimeter
Armed
AWAY
Yes
Yes
Yes
STAY*
Yes
Yes
Yes
INSTANT*
Yes
No
Yes
MAXIMUM
Yes
No
Yes
Alarms
When an alarm occurs, both the keypad and external sounders will sound, and the
keypad will display the zone(s) causing the alarm. If your system is connected to a
central monitoring station, an alarm message will also be sent. To stop the alarm
sounding, simply disarm the system.
Memory of Alarm
When an alarm condition occurs, the keypad displays the number(s) of the zone(s)
that caused the problem, and displays the type of alarm (ex. FIRE, ALARM). It
remains displayed until it is cleared by disarming the system (see DISARMING THE
SYSTEM section).

– 7 –
System Overview (cont’d)
Speed Key (Macros)
The system can store a string of up to 16 keystrokes, which can be activated
anytime by simply pressing the “D” key. This feature can be used to make it easy to
perform multiple functions at once (such as going to another partition to bypass a
zone), or it can be used to simplify an everyday, repeated procedure. Refer to the
SPEED KEY section for procedures for using this feature.
Using Schedules
Your system may have been programmed with schedules for automatically arming,
disarming and activating various devices and/or performing other system functions
at predetermined times. Users can modify some of these schedules by manually
delaying a closing time, using temporary schedules, or by programming special user
schedules. Refer to the USING SCHEDULES section at the end of this manual for
scheduling related procedures.
Device Timers
The system provides up to 20 "timers" that can be used to control various devices,
such as lights or appliances. These timers are similar in concept to the individual
appliance timers that might be purchased at a department store. The devices that
can be controlled are programmed into the system by the installer. Up to 16 of these
devices can be programmed. Refer to the PROGRAMMING DEVICE TIMERS section
for procedures.
To Access another Partition (GOTO Command)
Each keypad is assigned a default partition for display purposes, and will show only
that partition's information. But, if the user is authorized, a keypad in one partition
can be used to perform system functions in another partition, by using the GOTO
command. Note that only those partitions authorized and programmed by the
installer can be accessed in this manner.
To GOTO another partition, enter your security code, then press [*]followed by the
desired partition number (1-8).
The keypad will remain in the new partition until directed to go to another
partition, or until 2 minutes has elapsed with no keypad activity. Entering your
security code, pressing [*] followed by [0] will return the keypad to its original
partition.

– 8 –
System Overview (cont’d)
Master Keypad Operation
A "Master" keypad is one on which the status of all 8 partitions is displayed
simultaneously. A user can get more information about a certain partition by
simply entering [*]+ the desired partition number (1-8). To log on to the "Master"
partition (9) using the GOTO command, and to perform any functions at a Master
keypad, a user must have access to all partitions.
Self-Help Feature
Abbreviated user's instructions are built into the system that can be easily viewed
on the alpha keypad's message display screen. This feature will prove particularly
useful if this manual is not conveniently accessible when you need to perform a
system procedure with which you are not familiar.
To view the abbreviated instructions:
Simply press and hold down the function key of interest until the description starts
to appear (about 5 seconds) and then release it. The system must be “READY TO
ARM” to perform this function.
Refer to the FUNCTIONS OF THE KEYPAD section for descriptions of each key
function.
Phone Access & Voice Response Capability
Your system may include a 4286 VIP module that will permit you to access the
system via a Touch-tone phone, either on-premises or by call-in when away. The
phone access feature will enable you to do the following:
•Receive synthesized voice messages over the telephone regarding the status of
the security system.
•Arm and disarm the system and perform most function commands via the
telephone, with voice confirmation provided after each command entry.
•Control 4204/4204CF relays devices and lights and appliances through the #70
Manual Relay Activation mode.
Complete information regarding the use of this feature is provided in a separate
manual entitled PHONE ACCESS USER’S GUIDE, which accompanies the 4286 VIP
module.

– 9 –
About The Keypads
General
IMPORTANT: If the keypad beeps rapidly upon entering the
premises, it indicates that an alarm has occurred during your absence.
LEAVE IMMEDIATELY and CONTACT THE POLICE from a safe
location nearby.
Your keypads allow you to control all system functions. The keypads feature a
telephone style (digital) keypad and a Liquid Crystal Display (LCD) that shows the
nature and location of all occurrences. Keypad display back lighting is
programmable to always stay on or to light only when a key is pressed, then turn off
a few minutes later.
The keypads also feature a built-in sounder that will sound during alarms and
troubles. It will also "beep" during certain system functions, such as during
entry/exit delay times, during CHIME mode, and when depressing keys to perform
system functions (to acknowledge the key press). These sounds can be optionally
suppressed in some of your keypads (so as not to disturb other users of the system).
Ask your installer if this has been done.
The Alpha Keypad
Alpha keypads feature a 2-line, 32 character alphanumeric Liquid Crystal Display
(LCD) that can display system messages in user-friendly English. Abbreviated user's
instructions can also be displayed (see Self Help paragraph in the SYSTEM
OVERVIEW section). These keypads can also be programmed with custom zone
descriptors.

– 10 –
Functions of the Keypad
IMPORTANT! When using the keypad to enter codes and commands,
sequential key depressions must be made within 3 seconds of one another. If 3
seconds elapses without a key depression, the entry is aborted and must be
repeated from its beginning.

–11 –
Functions of the Keypad (cont’d)
ALPHA DISPLAY WINDOW: A 2-line, 32-
character Liquid Crystal Display (LCD) that
displays protection point identification and
system status, messages, and user instructions.
1 OFF : Disarms the burglary portion of the
system, silences alarms and audible trouble
indicators, and clears visual alarm trouble after
the problem has been corrected.
2 AWAY : Completely arms both perimeter
and interior burglary protection by sensing an
intruder's movements through protected
interior areas as well as guarding protected
doors, windows, etc. Late arrivals can enter
through an entry delay zone without causing
an alarm if the system is disarmed before the
entry delay time expires.
3 STAY : Arms the perimeter burglary
protection, guarding protected doors, windows
and other perimeter protection points, and
sounds an alarm if one is opened. Also allows
automatic bypassing of certain areas which
permits movement within your house without
causing an alarm. Late arrivals can enter
through an entry delay zone without causing
an alarm if the system is disarmed before the
entry delay time expires. See ARMING
PERIMETER ONLY for a full explanation of the
STAY key.
4 MAXIMUM : Arms in manner similar to
AWAY mode, but eliminates the entry delay
period, thus providing maximum protection.
An alarm will occur immediately upon opening
any protection point, including entry delay
zones.
5 TEST : Tests the system and alarm
sounder if disarmed.
6 BYPASS : Removes individual protection
zones from being monitored by the system.
Displays previously bypassed protection zones.
7 INSTANT : Arms in manner similar to
STAY mode, but turns off the entry delay
period, offering greater security while inside
and not expecting any late arrivals. An alarm
will occur immediately upon opening any
perimeter protection point, including entry
delay zones.
8 CODE : Allows the entry of additional user
codes that can be given to other users of the
system.

– 12 –
Functions of the Keypad (cont’d)
9 CHIME : Turns on & off the CHIME mode.
When on, any entry through a protected delay
or perimeter zone while the system is
disarmed will cause a tone to sound at the
Keypad(s).
*READY : When depressed prior to arming
the system, the keypad will display all open
protection zones within the keypad's home
partition. This key is also used to display all
zone descriptors that have been programmed
for your system, by holding the key down for at
least 5 seconds.
#: Permits ARMING of the system without
use of a security code ("Quick Arm", if
programmed).
KEYS 0-9: Used to enter your individual
security access code(s).
LED READY INDICATOR: (GREEN) Lit
indicates system is ready to be armed, while
unlit indicates system not ready.
LED ARMED INDICATOR: (RED) Lit when the
system has been armed (STAY, AWAY,
INSTANT or MAXIMUM).
SPEAKER: Source of audible internal warning
and confirmation sounds, as well as alarms
(see "Summary of Audible Notifications").
FUNCTION KEYS:These keys can be used for
Speedkey (macros) functions or panic keys.
Refer to the SPEEDKEY (MACROS) and PANIC
KEYS sections for descriptions of these
functions.

–13 –
Entry/Exit Delays
General Information
Your system has installer-programmed time delays, known as exit delay and entry
delay. Whenever you arm your system, exit delay gives you time to leave through
the designated exit door without setting off an alarm. Exit delay begins immediately
after entering any arming command, and applies to all modes of arming protection.
If programmed, a slow beeping will sound throughout the exit delay period.
Entry Delay gives you time to disarm the system when you reenter through the
designated entrance door. But the system must be disarmed before the entry delay
period ends, or an alarm will occur. The keypad will beep during the entry delay
period, reminding you to disarm the system. You can also arm the system with no
entry delay at all by using either INSTANT or MAXIMUM arming modes. These
modes provide greater security while on the premises or while away for extended
periods of time. See your installer for your delay times.

– 14 –
Security Codes and Authority Levels
General Information
At the time of installation, you were assigned an authority level and a personal four-
digit security code, known only to you and yours. The security code must be entered
when arming and disarming the system. The authority level defines the system
functions that you can perform.
As an additional safety feature, other users that do not have a need to know your
code can be assigned different security codes, and each user can be given a different
authority level. Users are identified by "user numbers", which are assigned when
assigning a user's security code.
All codes can be used interchangeably when performing system functions within the
limits of each code's authority level (a system armed with one user's code can be
disarmed by another user's code), with the exception of the Operator Level C code.
See AUTHORITY LEVELS on the following page for details regarding authority
levels.
Duress Code
This feature is intended for use if you are forced to disarm or arm the system under
threat. When used, the system will act normally, but can silently notify the central
station of your situation, if that service has been provided. The duress code is pre-
assigned by the installer during installation (authority level 6).
Important: This code is useful only when the system is connected to a central
station.
Quick Arming
Note that if "Quick Arming" was programmed by the installer, the [#] key can be
pressed in place of the security code when arming the system. The security code
must always be used to disarm the system, however.

–15 –
Security Codes and Authority Levels (cont’d)
Authority Levels
Authority levels define the system functions a particular user can perform.
Depending on the authority assigned to you, there are certain system functions you
may be prohibited from performing. In summary, there are six authority levels, each
having certain system restrictions as shown below.
Level 1 Master:Can perform all system functions in assigned
partitions, and can add, delete or change Manager and
Operator level users. Master codes are added by the
Installer.
Level 2 Manager: Can perform system functions in assigned partitions,
and can add, delete or change Operator level users.
Level 3 Operator A: Can perform system functions in assigned partitions,
but cannot add or delete other users.
Level 4 Operator B: Same as Operator A, except Operator B cannot bypass
zones of protection.
Level 5 Operator C: Can arm the system in assigned partitions, but cannot
disarm the system unless the system was armed with
this code. This code is typically assigned to someone
who has a need to arm/disarm the system only at
certain times (such as a baby-sitter).
Level 6 Duress: Can arm and disarm the system, but also sends a silent
panic alarm to the central station, if that service is
connected.
To view your authority level and system capabilities:
1. Enter your code + [*] +[*].
2. The keypad will display the partition(s) that you are authorized to operate, and
your user number and authority level in each partition.

– 16 –
Security Codes and Authority Levels (cont’d)
General Rules on Authority Levels and Changes
•A user may not delete or change the user code of the SAME or HIGHER authority
than which he is assigned.
•A user may only ADD users to a LOWER authority level.
•A user may assign access codes only to those partitions to which the user
adding the code has access. (Ex. a user with access to only partition 1 cannot
assign codes in partition 2.)
•The only way to assign a user's authority level is by using the "Add a User"
procedure. To change a user's authority level, that user must first be deleted,
and then added again.
•A user can only be DELETED or CHANGED from within the partition he is
assigned.
•User numbers must be entered as 2-digit entries. Single digit user numbers
must be preceded by a "00" (example, 03, 04, etc.). Security codes are entered
as 4-digit numbers.
•Before assigning a security code, be sure it does not conflict with any DURESS
code.
Note: When adding, changing or deleting users, all other alpha keypads in that
partition will display "User Edit Mode – Please Stand By", and key depressions
(except Panic) at those keypads will be ignored. Panic key depressions will cause an
alarm and terminate user entry.
To Exit User Edit Mode
You can exit any of the user edit modes described on the following pages at any time
by doing the following:
1. Press either * or # , or don't press any key for 10 seconds.
2. System returns to normal mode.

–17 –
Security Codes and Authority Levels (cont’d)
To Add a User
IMPORTANT: Temporary users should not be shown how to use any system
function they do not need to know (e.g. bypassing protection zones).
CODE
1. Enter Master or Manager code and press the 8 key.
2. Enter the new user's 2-digit User Number (02-75).
3. Enter 4-digit security code for that user. The following prompts will appear.
ADD NEW USER?
0 = NO , 1 = YES
Enter 1 to add a new user code. Entering 0 will change
the existing user's code to the code entered in step 3.
See Changing A User's Code section.
USER NUMBER = 03
ENTER AUTH. LEVEL
Enter the authority level, 1-6, for this user within this
partition.
1=master 2=manager 3=operator A
4=operator B 5=operator C 6=duress code
ACCESS GROUP?
ENTER 0-8
If access schedules have been programmed, this
prompt appears. Enter the user's access group number
(1-
8) if this user should have limited access to the
system. Enter 0 if no access group should be assigned.
RF BUTTON ?
0 = NO , 1 = YES
This prompt will appear if a 5800 series button
transmitter has been supplied and has not yet been
assigned to a user. Press 1 if a button transmitter will be
assigned to this user. Otherwise press 0.
ENTER BUTTON ZN #
(01-86)
If assigning a button transmitter, this prompt will
appear. Enter
the button's zone number (see your
installer for zone number).

– 18 –
Security Codes and Authority Levels (cont’d)
MULTI-ACCESS ?
0 = NO , 1 = YES
If you as a user have access to other partitions, the
keypad will prompt for ability of this new user to access
(GOTO
) those partitions. Press 0 (NO) or 1 (YES). If no,
the system activates this user code and exits “Add a
User” mode. If yes, the keypad prompts for the Global
Arm option for this user.
GLOBAL ARM ?
0 = NO , 1 = YES
Press 1 (YES) if this user will be allowed to try to arm
more than one partition at the same time. Press 0 if this
user will arm only his assigned partition.
PART.2 - SHOP?
0 = NO , 1 = YES
The keypad now prompts for the user’s access to the
next partition (see GOTO command). Again press 0 or 1.
If yes, the system will automatically assign a user
number for use in that partition and will prompt for
authority level and global arm options for this user
within the partition (see previous steps).
PART. 1 A0* WHSE
USER 03 AUTH=3G.
When all partitions have been displayed, the keypad will
scroll through the partition(s) to which access has been
assigned, and will display the user number, authority
level and global arm option for each. Th
e “G” after the
authority level indicates that the global arm feature is
active for this user in the displayed partition. The "*"
indicates the partition from which this user can be
changed or deleted. The "." at the end of the second line
indicates that t
his user sends open/close reports.
Open/close reporting is automatically active for any
users added by you, if you have open/close reporting
active.

–19 –
Security Codes and Authority Levels (cont’d)
To Change a User's Code
CODE
1. Enter Master or Manager code and press the 8 key + user number to be
changed.
2. Enter the new code for that user.
ADD NEW USER?
0 = NO , 1 = YES
The system will recognize that the user number is
already in use and will prompt whether or not this is a
new user. Enter 0 to change the existing user's code to
the code entered in step 3.
USER 02 CHANGED
SUCCESSFULLY
The system will confirm that the change is allowed
based on authorization level, and if so, will put the new
code into effect.
Note that if changing one’s own code, the system will
prompt for the new code to be re-
entered. This
prevents accidentally changing one's own code.
To Delete a User
CODE
1. Enter Master or Manager code and press the 8 key + user number to be
deleted.
2. Enter Master or Manager code first entered.
OK TO DELETE
0 = NO , 1 = YES
The system will recognize that the User number is
already in use and will prompt to confirm that it
should be deleted. Press 0 (NO) or 1 (YES).
USER CODE
DELETED
If yes, that user's code will be removed from all
partitions to which it was assigned, and all
authorization levels and other information about that
user will be deleted. Note that a user can only be
dele
ted from the partition in which it was first
assigned, and can only be deleted by a user with a
higher authority level. A User's security code cannot
be deleted by oneself.

– 20 –
Accessing Other Partitions
To Access another Partition
Each keypad is assigned a default partition for display purposes, and will show only
that partition's information. But, if the user is authorized, a keypad in one partition
can be used to perform system functions in other partitions by using the GOTO
command. Note that only those partitions authorized and programmed by the
installer can be accessed in this manner.
To GOTO another partition:
READY
1. Enter your security code, then press *+ partition number (0-8).
Entering partition number 0 will return the keypad to its original partition.
2..
LOG-ON TO AAAA
PART. X COMPLETE
The keypad will remain in the new partition until
directed to go to another partition, or until 2
minutes has elapsed with no keypad activity.
AAAA = alpha descriptor programmed by the
installer
X = partition number
Global Arming
The Global Arming option may be assigned for use by some users. If Global Arming
was enabled for use with your security code, a keypad prompt (message) shown
below appears after pressing one of the arming function keys (STAY, INSTANT,
AWAY, MAXIMUM, OFF).