ResMed S8 ESCAPE System User manual

1
USER’S MANUAL
English
338215-Eng/3 05 08
S8 Escape™ System
ENGLISH

1
S8 Escape™
ILLUSTRATIONS
ILLUSTRATIONS
FIGURAS
ILUSTRAÇÕES
Component of 338215/3
Composant du 338215/3
Componente de 338215/3
Componente de 338215/3
A
Keypad
Clavier
Teclado
Teclado
Carry handle
Poignée de transport
Asa para el transporte
Pega de transporte
Air filter cover
Couvercle du logement du
filtre à air
Cubierta del filtro de aire
Tampa do filtro de ar
Module
Module
Módulo
Módulo
DC input
Entrée CC
Entrada de CC
Entrada CC AC input
Entrée CA
Entrada de CA
Entrada CA
LCD screen
Écran LCD
Visor
Mostrador LCD
Air outlet
Sortie d'air
Salida de aire
Saída de ar
SYSTEM COMPONENTS / COMPOSANTS DU SYSTÈME / COMPONENTES DEL
SISTEMA / COMPONENTES DO SISTEMA
Air inlet
Entrée d'air
Entrada de aire
Entrada de ar
6’ 6”/2 m
2
34 5
OTHER ACCESSORIES / AUTRES ACCESSOIRES / OTROS ACCESORIOS /
OUTROS ACESSÓRIOS
C
1
5
SETTING UP THE S8™ / INSTALLATION DE LA S8 / INSTALACIÓN DEL S8
/ MONTAGEM DO S8
D
2
3
4
BINTEGRATED HUMIDIFIER / HUMIDIFICATEUR INTÉGRÉ/
HUMIDIFICADOR INTEGRADO / HUMIDIFICADOR INTEGRADO
32
9’ 10”/3 m 21”/52 cm
1
4
© 2005 ResMed Ltd.
© 2005 ResMed Ltd.
© 2005 ResMed Ltd.
© 2005 ResMed Ltd.
HumidAire 3i™
Connector plug
Cache du connecteur
Enchufe conector
Tampa do conector
338215r3 Illustrations.qxd 25/08/2005 1:50 PM Page 1

I
J
234
1
0
2
3
4
5
6
7
8
1
0
2
3
4
5
6
7
8
1
0
2
3
4
5
6
7
8
1234
USING A RESMED PASSOVER / UTILISATION D'UN PASSOVER RESMED / USO DE UN PASSOVER DE RESMED / UTILIZAÇÃO DE UM RESMED PASSOVER
USING A HUMIDAIRE™ / UTILISATION D'UN HUMIDAIRE / USO DE UN HUMIDAIRE / UTILIZAÇÃO DE UM HUMIDAIRE
HUSING THE DATA CARD / UTILISATION DE LA CARTE DE DONNÉES / USO DE LA TARJETA DE DATOS /
COMO USAR O CARTÃO DE DADOS
1
EHUMIDAIRE 3i and S8 ESCAPE / HUMIDAIRE 3i et S8 ESCAPE /
HUMIDAIRE 3i y S8 ESCAPE / HUMIDAIRE 3i e S8 ESCAPE
BLANK MODULE / MODULE VIERGE / MÓDULO EN BLANCO /
MÓDULO EM BRANCO
F
12
DATA CARD MODULE / MODULE DE CARTE DE DONNÉES /
MÓDULO TARJETA DE DATOS / COMO USAR O CARTÃO DE DADOS
G
12
1 32
© 2005 ResMed Ltd.
© 2005 ResMed Ltd.
© 2005 ResMed Ltd.
© 2005 ResMed Ltd.
© 2005 ResMed Ltd.
© 2005 ResMed Ltd.
Note: Some products not available in all regions. / Remarque : certains produits ne sont pas disponibles dans tous les
pays. / Nota: algunos productos no están disponibles en todas las regiones. / Nota:Alguns produtos não se encontram disponíveis em
todas as regiões.
Data
communications
port
Port de
communication
des données
Puerto de
comunicación
de datos
Porta de
comunicação
de dados
338215r3 Illustrations.qxd 25/08/2005 1:50 PM Page 2

ENGLISH
3
CONTENTS
CONTENTS
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
YOUR RESPONSIBILITY 5
MEDICAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
ABOUT THE S8 ESCAPE™ 5
CONTRAINDICATIONS 6
WARNINGS 6
CAUTIONS 7
ADVERSE EFFECTS 8
THE S8 ESCAPE SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
S8 ESCAPE 9
MASKS 9
HUMIDIFIERS 10
RESSCAN DATA CARD MODULE 10
ACCESSORIES 10
HOW TO USE THE S8 ESCAPE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
SET UPTHE S8 ESCAPE 11
ASSEMBLE THE MASK 11
START TREATMENT 11
STOP TREATMENT 12
HOW TO ATTACH AHUMIDIFIER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
ATTACH AHUMIDAIRE 3IHUMIDIFIER 13
ATTACH AHUMIDAIRE HUMIDIFIER 13
ATTACH ARESMED PASSOVER HUMIDIFIER 14
HOW TO USE THE KEYPAD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
HOW TO CHANGE THE SETTINGS ON YOUR S8 ESCAPE 16
S8 MODULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
USING ABLANK MODULE 19
USING ARESSCAN DATA CARD MODULE 19
CLEANING AND MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
DAILY CLEANING 22
WEEKLY CLEANING 22
PERIODIC CLEANING 22
REPLACING THE AIR FILTER 23
SERVICING 23
FREQUENTLY ASKED QUESTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

4
SYSTEM SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
S8 ESCAPE 29
ACCESSORIES 29
LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
INDEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

5
ENGLISH
INTRODUCTION
INTRODUCTION
Thank you for choosing the S8 ESCAPE™ flow generator. The S8 ESCAPE is a compact,
all-in-one package with an inbuilt power supply and the option of integrated data
management and humidification.
This user manual contains the information you need for the correct use of your
S8 ESCAPE.
YOUR RESPONSIBILITY
The owner or user of this system shall have sole responsibility and liability for any injury
to persons or damage to property resulting from:
•operation which is not in accordance with the operating instructions supplied
•maintenance or modifications carried out unless in accordance with authorized
instructions and by authorized persons.
Please read this manual carefully before use.
This manual contains special terms and icons that appear in the margins to draw your
attention to specific and important information.
•Warning alerts you to possible injury.
•Caution explains special measures for the safe and effective use of the device.
•Note is an informative or helpful note.
MEDICAL INFORMATION
ABOUT THE S8 ESCAPE™
The S8 ESCAPE continuous positive airway pressure (CPAP) system is indicated for the
treatment of obstructive sleep apnea (OSA) in adult patients.
The S8 ESCAPE CPAP system is intended for home and hospital use.
!
CAUTION
In the US, Federal law restricts this device to sale by or on the order of a physician.

6
CONTRAINDICATIONS
The S8 ESCAPE is not a life support device and may stop operating during power failure
or certain fault conditions. It should not be used by patients who are dependent on
continuous therapy.
Positive airway pressure therapy may be contraindicated in some patients with the
following pre-existing conditions:
•severe bullous lung disease
•pneumothorax
•pathologically low blood pressure
•dehydration
•cerebrospinal fluid leak, recent cranial surgery, or trauma.
WARNINGS
•Read the entire manual before using the S8 ESCAPE.
•Advice contained in this manual should not supersede instructions given by the
prescribing physician.
•A patient should not connect a device to the data communication port unless
instructed to do so by their health care provider or physician. Only ResMed
products are designed to be connected to the data communication port.
Connecting other devices could result in injury, or damage to the S8 ESCAPE
device.
•The S8 ESCAPE should only be used with masks (and connectors)*recommended
by ResMed, or by a physician or respiratory therapist. A mask should not be used
unless the S8 ESCAPE device is turned on and operating properly. The vent hole or
holes associated with the mask should never be blocked.
Explanation: The S8 ESCAPE is intended to be used with special masks (or
connectors)*which have vent holes to allow continuous flow of air out of the
mask. When the device is turned on and functioning properly, new air from the
device flushes the exhaled air out through the mask vent holes.
However, when the device is not operating, insufficient fresh air will be provided
through the mask, and the exhaled air may be rebreathed. Rebreathing of exhaled
air for longer than several minutes can, in some circumstances, lead to suffocation.
This applies to most models of CPAP devices.
•In the event of power failure or machine malfunction, remove the mask.
•The S8 ESCAPE can be set to deliver pressures up to 20 cm H2O. In the unlikely
event of certain fault conditions, pressures up to 30 cm H2O are possible.
* Ports may be incorporated into the mask or in connectors that are near the mask.

7
ENGLISH
MEDICAL INFORMATION
•If oxygen is used with this device, the oxygen flow must be turned off when the
device is not operating.
If oxygen has been left on, turn off the flow generator, then wait 30 minutes before
turning on the flow generatory again.
Explanation: When the CPAP device is not in operation and the oxygen flow is
left on, oxygen delivered into the air delivery tubing may accumulate within the
CPAP machine enclosure and create a risk of fire. This applies to most types of
CPAP machines.
•Oxygen supports combustion. Oxygen should not be used while you are
smoking or in the presence of an open flame.
•Always ensure airflow is being generated by the device before the oxygen
supply is turned on.
•Always turn the oxygen supply off before stopping the airflow from the device.
Note: At a fixed rate of supplemental oxygen flow, the inhaled oxygen concentration will
vary, depending on where the oxygen is introduced, the pressure settings, patient breathing
pattern, mask selection, and leak rate.
•Do not use the S8 ESCAPE if there are obvious external defects or unexplained
changes in performance.
•Do not open the S8 ESCAPE case. There are no user serviceable parts inside.
Repairs and internal servicing should only be performed by an authorized service
agent.
•Explosion hazard—do not use in the vicinity of flammable anesthetics.
CAUTIONS
•At low pressures, the flow through the exhalation ports of your mask may not
clear all exhaled gas from the tubing. Some rebreathing may occur.
•The airflow for breathing produced by this device can be as much as 11oF (6oC)
higher than the temperature of the room. Caution should be exercised if the room
temperature is warmer than 90oF (32oC).
•When AC mains power (100–240V AC) is not available, always use a ResMed
DC-12 converter. (The DC-12 converter is available as an optional accessory. It is
not supplied with all models.)
•If supplied, the Data Card module is designed for use with specific ResMed
devices.
•Only use the Data Card module (if supplied) as specified in this manual.
Note: The above are general warnings and cautions. Specific warnings, cautions, and
notes appear with the relevant instructions in the manual.

8
ADVERSE EFFECTS
Patients should report unusual chest pain, severe headache, or increased
breathlessness to their prescribing physician. An acute upper respiratory tract infection
may require temporary discontinuation of treatment.
The following side effects may arise during the course of therapy with the CPAP
device:
•drying of the nose, mouth, or throat
•nosebleed
•bloating
•ear or sinus discomfort
•eye irritation
•skin rashes
•chest discomfort.

9
ENGLISH
THE S8 ESCAPE SYSTEM
THE S8 ESCAPE SYSTEM
The S8 ESCAPE device is part of a system that consists of five elements:
•S8 ESCAPE flow generator
•Mask
•Humidifier
•Data management products
•Accessories.
S8 ESCAPE
Please refer to the illustrations in section Aof the illustration sheet.
FRONT VIEW (A-1)
Shows the keypad and LCD screen, and the air outlet.
REAR VIEW (A-2)
Shows where the module attaches, and the location of the air filter and power sockets.
POWER CORD (A-3)
Power cord to attach the S8 ESCAPE to the AC (mains) power.
CARRY BAG (A-4)
The S8 ESCAPE carry bag contains two pouches: one for storing the S8 device, the other
for storing the HUMIDAIRE 3
i™ . When storing the HUMIDAIRE 3 i , always put it in the
larger, mesh pouch.
AIR TUBING
The 6’6” (2 m) air tubing (A-5) connects the S8 ESCAPE to your mask . You will need
medium 21” (52 cm) air tubing (see C-3) to connect the S8 ESCAPE to the
HUMIDAIRE™and ResMed PASSOVER humidifiers.
MASKS
You will also need a ResMed mask system (supplied separately).
The ResMed mask systems that are recommended for use with the S8 ESCAPE are:
NASAL MASKS
•MODULAR NASAL MASK
•MIRAGE VISTA™ NASAL MASK
•ULTRA MIRAGE™ NASAL MASK
•MIRAGE™ NASAL MASK
•PROTEGE™ NASAL MASK
•MIRAGE ACTIVA™ NASAL MASK
•PAPILLON™.
NASAL PILLOWS SYSTEMS
•MIRAGE SWIFT™ NASAL PILLOWS SYSTEM.

10
FULL FACE MASKS
•MIRAGE™ FULL FACE MASK
•MIRAGE™ FULL FACE MASK SERIES 2
•ULTRA MIRAGE™ FULL FACE MASK.
!
WARNING
Only ResMed mask systems are compatible for use with the S8 Escape. Please refer
to “Warnings” on page 6.
HUMIDIFIERS
A humidifier may be required if you are experiencing dryness of the nose, throat, or
mouth. The S8 ESCAPE is compatible for use with:
•HUMIDAIRE 3i integrated heated humidifier (Figure Bon the illustrations sheet)
•HUMIDAIRE heated humidifier (Figure Ion the illustrations sheet)
•ResMed PASSOVER humidifier (Figure Jon the illustrations sheet).
RESSCAN DATA CARD MODULE
The RESSCAN™Data Card module and RESSCAN Data Card (C-1) may be used with
the S8 ESCAPE either to help your clinician to monitor your treatment or to provide
you with updates to your device settings. See “Using a ResScan Data Card Module”
on page 19 for information about how to use the Data Card module and Data Card.
ACCESSORIES
Please refer to the illustrations in section Cof the illustration sheet.
Other accessories for use with the S8 ESCAPE:
•Air tubing 9‘10” (3 m) (C-2)
•Medium air tubing 21” (52 cm) for HUMIDAIRE and ResMed PASSOVER connection
(C-3)
•DC-12 converter (C-4)
•Blank module (C-5).
Note: ResMed regularly releases new products. Please check our website at
<www.myresmed.com>.

11
ENGLISH
HOW TO USE THE S8 ESCAPE
HOW TO USE THE S8 ESCAPE
Please refer to the illustrations in section Dof the illustration sheet.
SET UPTHE S8 ESCAPE
1Place the S8 ESCAPE on a table near the head of your bed.
!
CAUTION
Be careful not to place the device where it can be bumped or where someone is
likely to trip over the power cord.
Note: You can also place your S8 Escape on the floor beside or underneath your bed.
Ensure that the area is free from dust and clear of bedding, clothes, or any other objects
that could block the air inlet.
2Connect the power cord to the socket at the rear of the flow generator (D-1). Plug
the other end of the power cord into the power outlet.
!
WARNING
Make sure the power cord and plug are in good condition and the equipment is not
damaged.
3Connect one end of the air tubing firmly onto the air outlet (D-2).
!
WARNING
•Only ResMed air tubing should be used with your flow generator. A different
type of air tubing may alter the pressure you actually receive, reducing the
effectiveness of your treatment.
•Blocking the hose while in operation could lead to overheating of the device.
•In the clinical environment any personal computer that is used with your CPAP
system must be at least 5’ (1.5 m) away from, or at least 8’ (2.5 m) above, the
patient. It must also comply with the relevant test standard. For personal
computers the international standard is IEC 60950 or equivalent.
ASSEMBLE THE MASK
1Assemble your mask system according to the mask user instructions.
2Connect your mask system to the free end of the air tubing (D-3).
The S8 ESCAPE is now ready for use (D-4).
START TREATMENT
1Make sure the power is on.
The product name is displayed briefly on the LCD screen, then the standby (Ramp)
screen appears. The key and LCD backlights also turn on.

12
2Lie down and arrange the air tubing so that it is free to move if you turn in your sleep.
!
CAUTION
•Do not leave long lengths of air tubing around the top of your bed. They could
twist around your head or neck while you are sleeping.
•Make sure the area around the flow generator is dry and clean. It should also be
clear of bedding, clothes, and other potential blockages.
3Alter the ramp time if required (see “How to Change the Ramp Time” on page 17).
4To start treatment, press the Start/Stop key.
5Fit your mask as described in the mask user instructions.
!
WARNING
A mask should not be used unless the S8 Escape device is turned on and operating
properly.
6When ramping begins the LCD will display the word "RAMPING", with the current
pressure indicated as dashes. Each dash is approximately equivalent to 2 cm H2O. For
example, 6 dashes represents approximately 12 cm H2O pressure.
STOP TREATMENT
To stop treatment at any time, remove your mask and press the Start/Stop key.

13
ENGLISH
HOW TO ATTACH AHUMIDIFIER
HOW TO ATTACH AHUMIDIFIER
ATTACH AHUMIDAIRE 3 i HUMIDIFIER
Please refer to the illustration in section Eof the illustration sheet, and your HumidAire 3i
manual.
The HUMIDAIRE 3
i attaches to the front of the S8 ESCAPE to provide heated
humidification. No other accessories are required for its use.
Notes:
a. Make sure the water chamber of the HumidAire 3i is empty before you attach or
detach the humidifier.
b. Remove the connector plug on the S8 Escape (see section Aof the illustration
sheet) before you attach the HumidAire 3i. Reattach the connector plug firmly
after you detach the HumidAire 3i.
STORING THE HUMIDAIRE 3
i
Store the HUMIDAIRE 3 i in the larger, mesh-top pouch of the S8 ESCAPE carry bag when
not in use.
ATTACH AHUMIDAIRE HUMIDIFIER
Please refer to the illustrations in section Iof the illustration sheet.
To connect your S8 ESCAPE to a HUMIDAIRE humidifier you need medium sized
21” (52 cm) air tubing.
1Fill the HUMIDAIRE water chamber and place inside the HUMIDAIRE. Connect the
medium 21” (52 cm) and long 6’6” (2 m) air tubing (I-1), and close the humidifier lid.
2Place the S8 ESCAPE on top of the HUMIDAIRE (I-2) and connect the free end of the
medium air tubing to the air outlet (I-3).
Note: To avoid water spilling into the S8 ESCAPE, do not put it underneath the humidifier.
3Assemble your mask system and connect it to the free end of the long air tubing (I-4).
4Plug the HUMIDAIRE power cord into a power outlet. Connect the S8 ESCAPE power
cord to the socket at the rear of the S8 ESCAPE and plug the other end into a power
outlet.
Please refer to the HumidAire User’s Manual for further details.
!
WARNING
Make sure that the power cord and plug are in good condition and the equipment
is not damaged.
The S8 ESCAPE is now ready for use with the HUMIDAIRE.

14
ATTACH ARESMED PASSOVER HUMIDIFIER
Please refer to the illustrations in section Jof the illustration sheet.
To connect your S8 ESCAPE to a ResMed PASSOVER humidifier you need medium sized
21” (52 cm) air tubing.
1 Fill the PASSOVER with water and connect the medium 21” (52 cm) and long
6’6” (2 m) air tubing ( J-1 ).
2Place the S8 ESCAPE on top of the PASSOVER (J-2) and connect the free end of the
medium air tubing to the air outlet (J-3).
Note: To avoid water spilling into the S8 ESCAPE, do not place it underneath the
humidifier.
3Assemble your mask system and connect it to the free end of the long air tubing (J-4).
4Connect the power cord to the socket at the rear of the S8 ESCAPE and plug the other
end into a power outlet.
Please refer to the ResMed Passover User’s Manual for further details.
!
WARNING
Make sure that the power cord and plug are in good condition and the equipment
is not damaged.
The S8 ESCAPE is now ready for use with the PASSOVER.

15
ENGLISH
HOW TO USE THE KEYPAD
HOW TO USE THE KEYPAD
The control panel of the S8 ESCAPE includes an LCD screen and keypad for navigating
through the menus and delivering treatment.
LCD SCREEN
The LCD screen displays the menus and treatment screens.
KEYPAD KEYS
The S8 ESCAPE keypad has the following keys:
BACKLIGHTS
The keypad and LCD are equipped with backlights that come on when the device is
powered. The LCD backlight turns off after two minutes of inactivity, and comes back
LCD screen
Left key
Up key
Right key
Start/Stop key
Down key
Key Function
Start/Stop • Starts or stops treatment.
Up • Allows you to increase settings options and scroll through
the S8 ESCAPE menu.
Down • Allows you to decrease settings options and scroll through
the S8 ESCAPE menu.
Left • Performs the function indicated by the guiding text displayed
above it on the LCD screen. Guiding text includes menu,
change, and apply.
Right • Performs the function indicated by the guiding text displayed
above it on the LCD screen. Guiding text includes exit and
cancel.

16
on when you press a key. Once the Start/Stop key has been pressed to start
treatment, the LCD backlight stays on for two minutes. The keypad backlight is always
on while the S8 ESCAPE is on.
HOW TO CHANGE THE SETTINGS ON YOUR S8 ESCAPE
You can change settings (such as Ramp Time, Altitude) on the S8 ESCAPE by using the
keypad and LCD. When the S8 ESCAPE is in standby mode you can display a series of
screens (a menu) on the LCD screen in order to view and change the settings for a
particular function.
Use the menu screens to change the ramp time, altitude compensation, and language.
You can also view details about the usage and software version of your S8 ESCAPE.
HOW TO ENTER THE MENU SCREENS
When the S8 ESCAPE standby screen is displayed you will see the word ‘Menu’ in the
left-hand corner. To select the S8 ESCAPE menu, press the Left key.
HOW TO SCROLL THROUGH THE MENU
When you are in the menu, scroll through items by pressing the Up or Down keys.
HOW TO CHANGE ASETTING OPTION
When you have scrolled to the item you require:
1. Press the Left key (Change).
2. Press the Up or Down keys until you see the setting option that you require.
3. Press the Left key (Apply) to select the setting option.
If you wish to exit without changing the option, press the Right key (Cancel).
S8 ESCAPE
S8 CLASSICRAMP 10min
Menu
S8 CLASSIC
PATIENT MENU
ALT: 0-2000ft
Change Exit
USED HRS: 960
Exit
USAGE: 120/180
Exit
SW: SX123456789
Exit
LANG: ENGLISH US
Change Exit

17
ENGLISH
HOW TO USE THE KEYPAD
HOW TO EXIT OUT OF AMENU
Press the Right key (Exit). This will take you back to the Patient Menu screen.
HOW TO EXIT OUT OF AN ITEM WITHIN THE MENU
Press the Right key (Exit).
HOW TO CHANGE THE RAMP TIME
During ramp time, the pressure increases from a low pressure to the prescribed
treatment pressure. You can set the ramp time in 5-minute intervals, from 0 minutes
(OFF) up to a maximum ramp time set by your clinician.
The standby screen displays the current ramp time in the right-hand corner. To change
the ramp time, press the Up or Down key until the desired ramp time appears.
Once a ramp time is selected, begin therapy by pressing the Start/Stop key.
When ramping begins the LCD will display the word "RAMPING", with the current
pressure indicated as dashes. Each dash is approximately equivalent to 2 cm H2O. For
example, six dashes represents approximately 12 cm H2O pressure.
HOW TO CHANGE THE ALTITUDE SETTING
If you move or travel with your S8 ESCAPE to areas of different altitude, you will need
to adjust the altitude compensation setting. Changes in altitude will affect the pressure
delivered by the S8 ESCAPE.
You can use the Altitude setting (ALT) to specify the altitude range at which you are
using your S8 ESCAPE. Select the S8 ESCAPE menu by pressing the Left key in the
standby (RAMP) screen. Scroll to ALT and select Change (Left key). Press the Up or
Down keys until you see the setting option that you require.
There are four altitude settings to choose from:
•0–2000ft (0–609 m)
•2001–4000ft (610–1219 m)
•4001–6000ft (1220–1828 m)
•6001–8500ft (1829–2591 m).
For example, if you are at an altitude of 3107’ (947 m), your altitude compensation
setting would be 2001–4000ft (610–1219 m), as 3107’ (947 m) falls within that range.
Press the Left key (Apply) to select the correct setting.
HOW TO CHANGE THE LANGUAGE SETTING
To display menus and messages in a different language, select the S8 ESCAPE menu by
pressing the Left key in the standby (Ramp) screen. Scroll to LANG and select Change
(Left key). Press the Up or Down keys until you see the language that you require.
OTHER VIEWABLE INFORMATION
You can also view the total number of hours of treatment (USED HRS); the number
of sessions that the S8 ESCAPE was used in a usage period (USAGE); and the current
software version installed on your unit (SW). Access to all of these screens is provided
via the menu. See “How to enter the menu screens” on page 16.

18
MESSAGES ON THE S8 ESCAPE LCD
Your clinician may have set your S8 ESCAPE to remind you about important events,
such as when to replace your mask, when to insert your Data Card (if your device is
Data Card enabled) and so on.
The reminder message is displayed on the LCD and is visible if the device is not
delivering therapy. The backlight on the LCD flashes when a message is displayed.
Your clinician can set any of the following reminders on your LCD:
Message Description Action
INSERT CARD May appear if
your device is
Data Card
enabled.
Insert your Data Card and follow any
instructions that your clinician has given
you. When you have done this, the
message will disappear from the LCD.
Pressing the Left (Ok) key will also
remove the message.
REPLACE
MASK
May appear when
your mask is due
for replacement.
Press the Left (Ok) key to remove the
message from your LCD, and replace your
mask with a new one.
CALL
PROVIDER
May appear as a
reminder to
contact your
clinician; for
example to
discuss how your
therapy is going.
Press the Left (Ok) key to remove the
message from your LCD, and contact your
clinician.
REPLACE
FILTER
May appear as a
reminder to
replace the air
filter on your
device.
Press the Left (Ok) key to remove the
message from your LCD, and replace the
air filter.
SERVICE DUE May appear as a
reminder to
return your
device for service.
Press the Left (Ok) key to remove the
message from your LCD, and contact your
clinician.

19
ENGLISH
S8 MODULES
S8 MODULES
Note: Do not remove modules while power is connected to the S8 Escape.
Your S8 ESCAPE will have one of two modules fitted to the back: a blank module or a
RESSCAN™Data Card module.
USING ABLANK MODULE
Please refer to the illustrations in section Fof the illustration sheet.
The blank module is a protective cover on the S8 ESCAPE. At times, you may wish to
remove or attach this module, for example to use the serial adapter.
To remove the blank module, pull it off the back of the S8 ESCAPE to show the data
communications port (F-1).
To attach the blank module, push the blank module onto the data communications
port, until the module clicks into place (F-2).
Note: To protect the data communications port, always ensure there is a module
attached to the device.
USING ARESSCAN DATA CARD MODULE
Please refer to the illustrations in section Gof the illustration sheet.
The RESSCAN Data Card module is an accessory to the S8 ESCAPE. Use a RESSCAN Data
Card with the Data Card module to collect data and update settings in the S8 ESCAPE.
The module and card give your clinician convenient access to data about your
treatment, and can provide you with new device settings from your clinician without
you having to leave home.
ATTACHING THE MODULE
To attach the Data Card module, push it onto the data communications port at the
back of your S8 ESCAPE until it clicks into place (G-1).
REMOVING THE MODULE
To remove the Data Card module, pull it off the back of the S8 ESCAPE (G-2).
Note: To protect the data communications port, always ensure there is a module
attached to the device.
USING THE DATA CARD TO COLLECT DATA
Please refer to the illustrations in section Hof the illustration sheet.
If your clinician needs to review your treatment, they will ask you to use the Data Card
to copy data from your S8 ESCAPE, and to return the card to them. The Data Card will
be provided in a convenient mailback envelope.
Data that is copied to a Data Card is still stored and available on the S8 ESCAPE.
It takes approximately five seconds to copy data onto the Data Card.