RH Baby&child BELLINDA User manual

B E L L I N A 9 D R A W E R S D R E S S E R - A S S E M B L Y I N S T R U C T I O N S
PARTS INCLUDED
A [1] DRESSER
B [4] LEGS
C [1] CENTER LEG
B
FIGURE 1
IMPORTANT SAFETY INSTRUCTIONS
1. Please read all instructions carefully before assembling.
2. For your safety, assembly by two or more adults is strongly recommended.
3. Keep instructions for future use.
4. Use only vendor-supplied hardware to assemble. Using unauthorized
hardware could jeopardize the structural integrity of the item.
DRYWALL WITH STUDS DRYWALL WITHOUT STUDS
FIGURE A FIGURE B
ASSEMBLY INSTRUCTIONS BY WALL TYPE
• DRYWALL WITH STUDS: Use screws to affix to drywall
with studs. See FIGURE A.
• DRYWALL WITHOUT STUDS: Use toggle bolt and screws
to affix to drywall. See FIGURE B.
ASSEMBLY INSTRUCTIONS
1. Lay the dresser (A) on a flat surface.
2. Align and insert the threaded rods of the legs (B) and center leg (C) into
the fixed nuts at the bottom of the Dresser (A), then turn the legs
clockwise to tighten. DO NOT OVER TIGHTEN. See FIGURE 1 & 2.
3. After assembly, turn the dresser upright on your desired location.
Fig.1
Fig.2
C
A
FIGURE 2
Metal Bracket
Clevis Pin
Hair Pin
Steel Aircraft Cable
Round-head Screw
Round-head Screw
Toggle Bolt 2 sets
2 pcs.
2 pcs.
2 pcs.
1 pc.
2 pcs.
2 pcs.
TOOLS NEEDED
Phillips-head Screwdriver (not included)
5
NO. SKETCH DESCRIPTION QTY.
2
1
3
4
HARDWARE INCLUDED
6
SPECIFICATION
1.6 x 162mm
51.5 x 16.5 x 16.5mm
(D2mm)
Ø6 x 23mm
Ø2 x 30mm
7
M4 x 15mm
M4 x 38mm
M3 x 51mm
12
/

B E L L I N A 9 D R A W E R S D R E S S E R - A S S E M B L Y I N S T R U C T I O N S
1
2
3
4
5
6
Wall
TOP
ANTI-TIPPING RESTRAINT INSTRUCTIONS
Young children may be injured by tipping furniture. The use of a tipping restraint is highly recommended.
When properly installed, this restraint could provide protection against the unexpected tipping of furniture due to small tremors, bumps or
climbing. We recommend mounting this restraint to a wall stud.
WARNING: This product is only a deterrent. It is not a substitute for proper adult supervision.
ANTI-TIP KIT INSTALLATION INSTRUCTIONS
1. Attach a metal bracket (1) near the
middle-top back edge of the furniture
piece by inserting the short screws (5).
2. Determine the final position of the
furniture piece. Mark a location on the
wall approximately 2" below the bracket
mounted to the back of the furniture.
3. Attach the second bracket to a wall stud
by inserting the long screw (6) (see
Figure A) or toggle bolt (7) through the
drywall (see Figure B).
4. Place the furniture so that the bracket
on the back edge aligns with the
bracket on the wall.
5. Insert the clevis pin (2) through the
holes on the bracket on the back of the
furniture and the hole on the steel
aircraft cable (3). Insert a hair pin (4)
through the small hole on the clevis pin
(2) to lock it.
6. Repeat above step to attach the other
end of the aircraft cable (3) to the
bracket on the wall.
7. Check to make sure the steel aircraft
cable is securely laced and locked to
the brackets.
WARNING: Always mount metal brackets to solid wood
part of furniture. Do not attach to plywood of back panels.
ATTACH THE ANTI-TIP KIT TO A WALL STUD IF
POSSIBLE, OR HAVE A PROFESSIONAL ATTACH THE
KIT TO MASONRY OR A CONCRETE WALL.
CARE INSTRUCTIONS
1. Dust often using a clean, soft, dry and lint-free cloth.
2. Blot spills immediately and wipe with a clean, damp cloth.
3. Do not use chemical cleaners, abrasives or furniture polish, as they may damage the finish.
22
/