Rhino-Rack Rhino 2500 Series User manual

Maximum carrying capacity: 75kg (165lbs) evenly distributed over crossbars. Please refer to your vehicle
 manufacturershandbookandDKSpecicationsheetformaximumroofloading.
 Alwaysusethelowerofthetwogures.
Recommendations:
It is essential that all bolt connections be checked after driving a short distance when you rst install your crossbars. Bolt con-
nections should be checked again at regular intervals (probably once a week is enough, depending on road conditions, usage,
loads and distances travelled). You should also check the crossbars each time they are retted. Make sure to fasten your load
securely. Please ensure that all loads are evenly distributed and that the centre of gravity is kept as low as possible.
Use only non-stretch fastening ropes or straps.
Load Ratings
When these roof racks are to be used on a vehicle that is driven off sealed roads, the manufacturer maximum roof load rating (to
be found in the vehicles User Manual) should be halved. For example, if the vehicles maximum roof load rating is 70kgs (sub-
tract 5kg - weight of crossbar and legs), these racks, when tted to this vehicle should have no more than 35kgs loaded on them
Caution:
The handling characteristics of the vehicle changes when you transport a load on the roof. For safety reasons we recommend
you exercise extreme care when transporting wind-resistant loads. Special consideration must be taken into account when cor-
nering and braking.Please remove crossbars when putting vehicle through an automatic car wash.
Note for Dealers and Fitters:
It is your responsibility to ensure instructions are given to the end user or client.
Rhino 2500 Series - Two Bar Heavy Duty System.
Important: Please refer to your tting instruction to ensure that the roof racks are installed in the correct locations.
Check the contents of kit before commencing tment and report any discrepancies.
Place these instructions in the vehicle’s glove box after installation is complete.

WARNING! Important Load Carrying Instructions
With utility vehicles, the cabin and the canopy move
independently. Roofracks and vehicle can be damaged if the
item transported is rigidly xed at points on both the cabin and
canopy. Instead, rigidly x to either the cabin roofracks or the
canopy roofracks.
When these roof racks are to be
used on a vehicle that is driven off
sealed roads, the manufacturer
maximum roof load rating (to be
found in the vehicles User Manual)
should be halved. Do not forget to
subtract 5kg from your maximum
carrying capacity due to the weight
of the crossbars and legs.
!
!
!
ü
ü
km/h X
YES
YES
NO
ü
ü
X
? kg
2 x Crossbars = 5kg
70kg load rating
(Urban road) 35 kg load rating (Off road - 70kg / 2)
=
Rhino 2500 Series - Two Bar Heavy Duty System

Attach hardware:
a. Attach the heavy duty cross bar adaptor onto top of the leg. Push to snap in place.
b. Locate the M6 x 25mm security screw, spring washer and at washer through top of the leg and fasten to
the M6 channel nut. Do not tighten at this stage.
c. Make sure the M8 pivot is correctly located as shown below.
1
Angled face of pivot
nut faces out.
a. b. c.
Rhino 2500 Series - Two Bar Heavy Duty System
Rhino 2500 Series - Two Bar Heavy Duty System
Parts List
Tools Required:
Security Allen key, provided in kit.
Tape measure.
Rubber mallet.
1
2
3
4
5
6
7
8
9
14
15
11
10
13
12
16
17
18
CarryingCapacity:RefertoDKspecicationsheetformaximumcarryingcapacityofyourparticularvehicle.
NOTE: RefertotheDKkitspecicationsheetforcorrectplacement(Front & Rear, Left & Right) of the foot plate, rubber
pad and metal strap. Also refer for sizes to cut the bar measurement strips.
Pad & clamp kit
available separately
Item Component Name Qty Part No.
1 Rubber Buffer Strip 2
2 Heavy Duty Cross Bar 2
3 M8 Pivot Nut 4 N047
4 M8 x 50mm Security Bolt 4 B154
5 End Cap 4 M002
6 Heavy Duty Cross Bar Adaptor 4 M315
7 Leg 4 M310
8 Leg Cover Plate 4 M324
9 M6 Channel Nut 4 N002
10 M6 Flat Washer 4 W031
11 M6 Spring Washer 4 W004
12 M6 x 25mm Security Screw 4 B137
13 Front Cover 4 M312
14 Front Cover Key 2 M314
15 Foot Plate 4 M311
16 Security Allen Key 1 SecKey-L
17 Leg Location Decals 4 S365
18 Arrow Positioning Decals 4 S364
19 Fitting Instruction 1 RR244

4
5
3Attach foot plate to leg.
Clip the foot plate onto base of the leg with the arrow
facing In or Out according to your vehicle listed in the
DK specication sheet. Diagram at left shows arrow
facing Out.
FRONT Cross Bar
VEHICLE Build FRONT Pad Pad Clamp Clamp Foot Plate Measurement HD bar
Date BAR OSF NSF OSF NSF Arrow Dir. Strip length Dist. ‘X’
Sample Vehicle 2005 on 1180mm M415 M415 SUB0172 SUB0172 OUT 108mm 894mm
DK spec sheet.
example only.
Crossbar rubber:
Push the cross bar rubber buffer strip into top of the bar.
Attach cross bar:
a. Locate leg with channel nut into cross bar.
b. Turn to locate the channel nut to sit across the bar.
b.a. Channel nut must
sit across the bar.
Attach pad to foot plate.
Clip the rubber pad onto the foot plate. Pad centre tube and end tabs must fully locate into the foot plate.
Note: Certain rubber pad sets have a DK supplement sheet to show correct orientation.
2
Centre tube.
End tabs clip in.
Centre tube pushes
through.
End tabs.
Rhino 2500 Series - Two Bar Heavy Duty System

Position roof racks:
Place racks onto the vehicle roof.
Refer to DK specication sheet for correct positioning of your roof racks.
A. Measure forward from a centre line of where the front and rear doors
meet/close.
B. Measure back to set distance between cross bars.
A and B measurements are to be in line with arrow in centre of foot plate.
8
B
A
Arrow on foot plate.
Front Rear
Leg location decals:
Stick the leg position labels inside the leg. The
labels are used to easily identify front and rear
cross bars if they are removed from vehicle.
Refer layout below.
7
Decal.
Measurement between legs:
Accurately measure between the legs to set the correct distance. Refer to DK specication sheet for vehicle
specic distance. Also set equal cross bar over hang. Tighten M6 security screw to 4-5 Nm (35-44 lbf.in)
6
FRONT Cross Bar
VEHICLE Build FRONT Pad Pad Clamp Clamp Foot Plate Measurement HD Cross Bar
Date BAR OSF NSF OSF NSF Arrow Dir. Strip length distance ( x ).
Sample Vehicle 2005 on 1180mm M415 M415 SUB0172 SUB0172 OUT 101mm 894mm / 35,13/64”
DK spec sheet.
‘x’
Equal over hang
= =
example size only.
Measure to edge
of heavy duty cross
bar adaptor.
Rhino 2500 Series - Two Bar Heavy Duty System
Rhino 2500 Series - Two Bar Heavy Duty System

Attach front cover.
Insert the two lugs on left side of front cover into the leg.
Use key provided to turn lock barrel to the open position
(O). Engage locking tab into leg. Turn to close (C).
Front cover key.
Open.
Closed.
11
10 Attach clamps:
a. Hook the lower part of the metal clamp in at the top of the door jamb underneath any rubber seals that may
be present. Fasten the M8 bolt to the pivot nut in the leg.
b. Bolts must be tensioned evenly on each side of the vehicle to avoid pulling the rack to one side.
Do not tighten one side at a time. Tighten M8 bolt to 12-14 Nm (106-123 lbf.in).
Refer to DK instruction for correct clamp and pad combination for front and rear of vehicle.
c. Knock end caps into end of cross bars. A rubber mallet may be used.
a.
b.
c.
X
ü
9Positioning decals:
Stick the white arrow decals in line with foot plate arrows onto the body work inside the door jamb. This marks
reference points for future use when racks are removed and then replaced.
Rhino 2500 Series - Two Bar Heavy Duty System

Rhino Rack 2500 Series - DK118
FRONT
VEHICLE Date Crossbar Pad / Clamp Pad / Clamp Foot plate Bar measurement HD Crossbar
FRONT RIGHT FRONT LEFT arrow direction strip. Length per side. distance ( x ).
VW Golf/GTI/R32 Mk5 5dr hatch 2004-2009 1180mm M366 / SUB0149 M366 / SUB0149 OUT 146mm 970mm / 38,3/16”
VW Rabbit Mk5 5dr hatch 2006-2009 1180mm M366 / SUB0149 M366 / SUB0149 OUT 146mm 970mm / 38,3/16”
VEHICLE Date Crossbar Pad / Clamp Pad / Clamp Foot plate Bar measurement HD Crossbar
REAR RIGHT REAR LEFT arrow direction strip. Length per side. distance ( x ).
VW Golf/GTI/R32 Mk5 5dr hatch 2004-2009 1180mm M366 / SUB0145 M366 / SUB0145 OUT 123mm 924mm / 36,3/8”
VW Rabbit Mk5 5dr hatch 2006-2009 1180mm M366 / SUB0145 M366 / SUB0145 OUT 123mm 924mm / 36,3/8”
REAR

Rhino Rack 2500 Series - DK118
A
BREARFRONT
Measurement A: CENTRE of door jamb to CENTRE arrow of leg foot plate.
Measurement B: CENTRE of Front leg foot plate arrow to CENTRE of Rear leg foot plate arrow.
Carrying capacity: Roof rack is rated to 75kg. Please refer to manufacturers handbook for your vehicles maximum roof load capacity. Always use the lower of the two gures.
VEHICLE Date Measurement A Measurement B Load rating (includes racks 5kg / 11lbs)
VW Golf/GTI/R32 Mk5 5dr hatch 2004-2009 200mm / 7,7/8” 750mm / 29,17/32” 75kg / 165lbs
VW Rabbit Mk5 5dr hatch 2006-2009 200mm / 7,7/8” 750mm / 29,17/32” 75kg / 165lbs
RHINO-RACK CARGO CARRIERS ROOF BARS