Rhino-Rack RTL008 User manual

Page 1 of 4
RTL008 T-Load Hitch Mount MK2
1. Check Part No./Kit is correct 3. Fit roof rack accessory
2. Read through instruction before installing 4. Check and recheck all fasteners are secure
Important Information
Maximum carrying capacity: 60kg (132lbs)
Please refer to your vehicle manufacturers handbook for maximum carrying capacity of your tow bar. Always use the lower of the
two fi gures. Load must be evenly distributed over the crossbars.
Warning: This product requires a certain level of manual handling of long and sometimes heavy objects. Ensure that
you have assessed the following criteria before carrying out a lift. 1 - Your physical ability and strength. 2 - Your general
state of health and fi tness. 3 - Dimensions of the object, such as height reach and grip areas
Unless stated otherwise in these instructions, all fasteners should be set to the following torque settings -
M6: 4-5Nm (3-4lbs/ft), M8: 8-10Nm (6-7.5lbs/ft) and M10: 16-18Nm (12-13lbs/ft).
Do not attempt to fi t the T-load to your vehicle unless you fully understand this fi tting instructions. Please direct any questions
regarding fi tting to the dealer from where the T-load was purchased.
Recommendations:
It is essential that all bolt connections be checked after driving a short distance when you fi rst install your roof racks and T-load.
Bolt connections should be checked again at regular intervals (once a week is enough, depending on road conditions, usage,
loads and distances travelled). You should also check the roof racks and T-Load each time they are re-fi tted. Always make sure
to fasten your load securely. Please also ensure that all loads are evenly distributed and that the centre of gravity is kept as low
as possible. Long loads (e.g. canoes and kayaks) must be secured front and rear with non-stretch fastening ropes or straps.
Roof racks must be removed when putting vehicle through an automatic car wash.
Caution: The handling characteristics of the vehicle changes when you transport a load on the roof. For safety reasons we
recommend you exercise extreme care when transporting wind-resistant loads. Special consideration must be taken into account
when cornering and braking.
Note for Dealers and Fitters:
It is your responsibility to ensure these fi tting instructions are given to the end user or client.
Rhino-Rack
22 Hanson Place, Eastern Creek,
NSW 2776, Australia. Document No: R1769 Fit Time: 20min
(Ph) [phone] Prepared By: Kayle Everett Issue No: 04
rhinorack.com.au Authorised By: Adam Connellan Issue Date: 22/11/2018
These instructions remain the property of Rhino-Rack Australia Pty Ltd and may not be used or changed for any other purpose
than intended.
!- Warning: Not recommended for
off road use.
- Use of RTLK recommended to
support load. Highly recommended
for kayaks to stop sliding on
uneven ground.
CONTROLLED

Page 2 of 4
RTL008 T-Load Hitch Mount MK2
Item Components Qty Part No.
1 End Cap 2 M153
2a Crossbar 1 A517
2b Rubber Strip 1 R011
3 T-section 1 -
4 800mm Support Bar 1 -
5a Loader Body 1 -
5b Loader Base 1 -
6 M8 x 60mm Button Head Screw 3 -
7 M8 x 16mm Flat Washer 6 W043
8 M8 Nyloc Nut 3 N028
9 M12 x 24mm Flat Washer 2 W045
10 M12 Nyloc Nut 1 N034
11 M12 x 70mm Carriage Bolt 1 SP155
12 Metal Key 2 -
13 Locking Pin 1 -
14 Spanner 2 -
15 Allen Key 1 -
16 Flat Washer 27mm 1 -
17 Hitch Bolt 1/2” - 13 x 3.25” 1 -
18 Pin Leash 1 -
19 Spring Washer 1/2” 1 -
20 Hitch Pin R Clip 1 -
21 M6 Carriage Bolt 2 -
22 M6 Nyloc Nut 4 N013
23 M6 Dome Head Screw 2 B064
24 M6 Spring Washer 2 W004
25 M6 x 16mm Flat Washer 2 W031
26 M6 Nut 2 N057
27 M6 Button Head Cap Screw 1 -
28 M6 Latch Nut 2 -
29 M8 Screw Knob -
30 Protective Mat 1 M711
31 Allen Key 1 H021
32 Instructions 1 R1769
1
3
2a Slide item 5a into
5b and fi x in place.
27.
29.
22.
28.
2b
10.
9.
7.
8.
7.
3.
6.
22.
16.
7. 8. 1.
2a.
4.
5a.
12.
11.
15.
14. 13.
26.
17.
18.
20.
23.
24.
25.
19.
21.
6.
27.
22.
5b. 28.
22.
8.
18.
29.
30.
26.
23.
24.
25.
1.
2b.
31.
2b.
33.
6.
7.
8.
7.
6.
7.
8.
7.
3.
4.
15.
3.
4.
5.

Page 3 of 4
RTL008 T-Load Hitch Mount MK2
5
1. Remove locking pin.
2. Drop the retention lever and lower the arm.
To lower the T-loader:
6
7
1. Pull the retention
lever back into a
locked position.
2. Replace the locking
pin to secure the loader
in an upright position.
8For long loads be sure to tie down appropriately. Note
that tie downs are sold as separate. Be sure load is level
and secure.
4
Use the key provided to unlock
the pin lock. When the Hitch Pin is
inserted, re-lock with the key. Remove
the key.
Insert the assembly into the hitch of the vehicle. Lock
in place using the locking pin as shown.
16. 17.
18.
19.
!
Note: For 1 1/4” hitch
mounts, remove the hitch
packers before installing
assembly.
Unscrew the pin
from the nut on the
opposite side of
the loader.
The lever will drop,
releasing the arm.
Check spring, if not
operating properly,
loosen with a 4mm
allen key.
!
Note:
Always use the
included rubber
mat. RTLK
must be used
when loading
to stop load
shifting/ sliding
at this stage.
Always assess
the likelihood
of slipping.
Always access
the conditions
and if it is not
safe, do not
use this loader.
!Always engage pin
during use.

Page 4 of 4
RTL008 T-Load Hitch Mount MK2
The loader can be set for a height suiting your vehicle. (A) Using a marker, create a reference either side of the
support bar as shown. Drill through these references (B) and then seal with cold galvanising paint. Fix with locking
pin (C).
Optional
(B) Drill a pilot hole with a 3mm drill bit.
Open up holes drilled with a 10mm drill bit
to fi nish.
Min height: 940mm
Max height: 1500mm
18.
(A) (C)