Rice Lake iDimension Plus User manual

iDimension® Plus
Static Dimensioning System
Managers Guide
PN 195441December 16, 2019

An ISO 9001 registered company
© Rice Lake Weighing Systems. All rights reserved.
Rice Lake Weighing Systems® is a registered trademark of
Rice Lake Weighing Systems.
All other brand or product names within this publication are trademarks or
registered trademarks of their respective companies.
All information contained within this publication is, to the best of our knowledge, complete and
accurate at the time of publication. Rice Lake Weighing Systems reserves the right to make
changes to the technology, features, specifications and design of the equipment without notice.
The most current version of this publication, software, firmware and all other product
updates can be found on our website:
www.ricelake.com

Contents
© Rice Lake Weighing Systems ● All Rights Reserved i
Contents
Technical training seminars are available through Rice Lake Weighing Systems.
Course descriptions and dates can be viewed at www.ricelake.com/training
or obtained by calling 715-234-9171 and asking for the training department.
1.0 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.1 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.2 Regulatory Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
1.3 Network Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
1.3.1 Accessing QubeVu Manager via Web Browser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
1.3.2 Accessing QubeVu Manager on 169.254.1.1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
1.3.3 Direct Connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
1.3.4 Network Connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
2.0 QubeVu Login Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.1 Navigation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.2 Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.2.1 Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.2.2 Restart/Reboot iDimension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.3 QubeVu Inspector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.4 Device Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.5 Change Log. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.6 Long Term Storage Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.6.1 Enabling Long Term Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.6.2 Viewing Long Term Storage Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.7 Displays. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.7.1 Operator Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.7.2 Customer Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.7.3 Demo Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3.0 Operator Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
3.1 Extract Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4.0 Admin Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
4.1 Admin Tools Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
4.1.1 Edit/Cancel/Save Keys. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
5.0 Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
5.1 Setup Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
5.2 General Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
5.2.1 General Settings Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
5.2.2 Scale . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
5.2.3 Display Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
5.2.4 Disk Finder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
5.2.5 Depth Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
5.3 External Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
5.3.1 Serial Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
5.3.2 Data Extraction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
5.3.3 Date/Time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
5.3.4 Measurement Settings Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
5.4 Display Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
5.5 User. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
5.6 Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
5.6.1 Network Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

iDimension Plus
ii Visit our website www.RiceLake.com
Rice Lake continually offers web-based video training on a growing selection
of product-related topics at no cost. Visit www.ricelake.com/webinars
6.0 Calibration Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
6.1 Calibration Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
6.1.1 Calibration Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
6.2 Calibration Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
6.2.1 Zone of Interest . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
6.2.2 Zone of Interest Configuration Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
6.3 Camera Calibration from QubeVu Manager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
6.3.1 Camera Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
7.0 Capture Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
7.1 Capture Definition Triggers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
7.2 New Capture Definition Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
8.0 Firmware Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
8.1 Firmware Upgrade Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
8.1.1 USB Drive or Network Share . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
8.1.2 Local File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
8.2 Updating Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
8.3 Custom Logo Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
9.0 Backup and Restore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
9.1 Backup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
9.2 Restore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
10.0 Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
10.1 Diagnostics Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
10.1.1 Component Tests. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
10.1.2 Scale Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
10.1.3 System Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
10.1.4 Debug Info . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
10.2 TCP Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
10.2.1 TCP Interface Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
10.2.2 Client/PC Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
10.3 HTTP Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
10.3.1 Configuring the HTTP Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
11.0 Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
11.1 Status Messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
11.1.1 Extended Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
11.1.2 Error Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
11.2 Appendix C: Sample XSL File. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
11.2.1 Data Extraction Configuration Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
11.2.2 Data Collection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
11.2.3 Data Extraction Definition. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
12.0 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

Introduction
© Rice Lake Weighing Systems ● All Rights Reserved 1
1.0 Introduction
The QubeVu Manager is a program provided to set up and configure the iDimension Plus and is recommended for use by
technical system administrators.
When interfacing this device to a third parties software program, please reference the software manufacturer’s documentation
for setup and configuration parameters as necessary.
Manuals and additional resources are available from the Rice Lake Weighing Systems website at www.ricelake.com
Warranty information can be found on the website at www.ricelake.com/warranties
1.1 Safety
Safety Signal Definitions:
Indicates an imminently hazardous situation that, if not avoided, will result in death or serious injury. Includes
hazards that are exposed when guards are removed.
Indicates a potentially hazardous situation that, if not avoided, could result in serious injury or death. Includes
hazards that are exposed when guards are removed.
Indicates a potentially hazardous situation that, if not avoided, could result in minor or moderate injury.
Indicates information about procedures that, if not observed, could result in damage to equipment or corruption
to and loss of data.
General Safety
Do not operate or work on this equipment unless this manual has been read and all instructions are understood.
Failure to follow the instructions or heed the warnings could result in injury or death. Contact any Rice Lake
Weighing Systems dealer for replacement manuals.
Failure to heed could result in serious injury or death.
Electric shock hazard!
There are no user serviceable parts. Refer to qualified service personnel for service.
The unit has no power switch, to completely remove D/C power from the unit, disconnect the D/C power cable from the
main socket.
For pluggable equipment the socket outlet must be installed near the equipment and must be easily accessible.
Always disconnect from main power before performing any work on the device.
Do not allow minors (children) or inexperienced persons to operate this unit.
Do not operate without all shields and guards in place.
Do not use for purposes other then weighing applications.
Do not place fingers into slots or possible pinch points.
Do not use this product if any of the components are cracked.
Do not make alterations or modifications to the unit.
Do not remove or obscure warning labels.
Do not use near water.
DANGER
WARNING
CAUTION
IMPORTANT
WARNING

iDimension Plus
2 Visit our website www.RiceLake.com
1.2 Regulatory Information
This product is a Class 1 Laser Product according to IEC 60825-1:2007 Ed. 2.0 and complies with 21 CFR 1040.1
pursuant to Laser Notice No. 50. A laser source with a diffraction optical element is embedded in the product, which
produces a maximum output power of 1.1 mW at the aperture with a maximum wavelength of 825 nm.
FCC
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at their own expense.
Changes or modifications not expressly approved by Rice Lake Weighing Systems could void the user’s FCC granted
authority to operate the equipment.
1.3 Network Connection
To establish a secure connection to the iDimension Plus, connect the unit via web browser or Ethernet.
DHCP is enabled by default.
1.3.1 Accessing QubeVu Manager via Web Browser
Compatible web browser:
• Google Chrome 25.0 or higher
1.3.2 Accessing QubeVu Manager on 169.254.1.1
Connect a computer to the iDimension with the Ethernet cable, either directly or over the network.
Type the IP address of the iDimension into a browser to access the QubeVu Manager tools.
If this is the initial configuration, the computer must be connected directly to the iDimension.
1.3.3 Direct Connection
Connect the iDimension directly to a computer with an Ethernet cable. If an Ethernet port is not available on the computer,
contact Rice Lake Service for support using the USB to Ethernet Adapter (PN 175621).
1.3.4 Network Connection
The iDimension can be installed on the network with the Ethernet cable, and configured with a static IP address or using DHCP.
Consult the network administrator to determine the best approach.
Network Settings (Windows)
To access QubeVu Manager, configure the local area connection.
1. Press the Windows + R keys.
2. Within the open field type the following: control ncpa.cpl.
Figure 1-1. Run Shell Open
Note

Introduction
© Rice Lake Weighing Systems ● All Rights Reserved 3
3. Select Ok.
Figure 1-2. Run Shell Confirmation
4. Network Connections will display.
Figure 1-3. Network Connections
5. Right-click on a Local Area Connection.
Figure 1-4. Network Options
6. Select Properties.
Figure 1-5. Network Properties

iDimension Plus
4 Visit our website www.RiceLake.com
7. Select Internet Protocol Version 4 (TCP/IPv4) by double-clicking.
Figure 1-6. Local Area Connection Properties
8. Select Use the following IP address.
Figure 1-7. IP Address Selection
9. Change the IP address to 169.254.1.10.
Figure 1-8. IP Address Configuration
10. Change the Subnet mask to 255.255.255.0.
Figure 1-9. Subnet Mask Configuration
11. Select Ok.
Figure 1-10. Configuration Confirmation
12. Open an Internet browser.
13. Type 169.254.1.1 in the address bar and press the Enter key to display the iDimension QubeVu Manager.
For operation instructions see the iDimension Operation Manual (PN 195439).
Note

QubeVu Login Screen
© Rice Lake Weighing Systems ● All Rights Reserved 5
2.0 QubeVu Login Screen
The Qubevu Manager is the firmware installed on the iDimension Plus dimensioning head that provides more advanced
configuration or features, system diagnostics and calibration not accessible from the touch screen operator display.
To access the QubeVu Manager firmware, connecting the device to an Ethernet port on a computer.
To view the QubeVu Manager, open an Internet browser and enter http://169.254.1.1. If using DHCP or static IP address,
replace 169.254.1.1 with the IP address provided by the network administrator.
Figure 2-1. QubeVu Manager Home Page
2.1 Navigation
A navigation menu is located in the upper left section of all pages. This allows users to keep track of their current location and
provides links back to each preceding page.
Example: The user is in the Calibration Settings screen and can select Admin Tools to return to the Admin Tools
menu or Qubevu Manager to return to the home page.
Figure 2-2. Navigation Menu

iDimension Plus
6 Visit our website www.RiceLake.com
2.2 Status
The status of the connected device is displayed in the upper right corner of all pages.
Example:
User: Logged into the device under the Admin mode. Select Log Out to return to the standard user mode.
Device: The default setting is the serial number of the iDimension. This can be renamed within the Network
Settings while in the Admin mode.
Running: The current status of the unit.
Address: 10.10.1.2: The Current IP address of the unit.
Figure 2-3. Status Display
If edit has been selected while in a screen, the unit may stay in the Configuring status and a restart is required to return to the
Running mode.
2.2.1 Status Messages
The device status messages which may be displayed are described below.
Item No. Description
1 User
2 Device and System Status
3 IP Address
Table 2-1. Status Indicators
Status Description
STARTING The system is starting up
STARTED The device has been power cycled or rebooted; Wait for the status to change to RUNNING before performing a dimension;
If the device remains in STARTING mode, use the demo display or USB display Help button to view and clear dimensions
ERROR The web browser is unable to determine the status; ERROR may display during a system reboot
STOPPING The system is transitioning into STOPPED state
STOPPED The service has stopped. STOPPED displays during a restart or reboot of the system; If the unit continues to display STOPPED,
perform a restart or power cycle the unit from the AC Outlet
RESTARTING The device has been power cycled, reset or rebooted and the system is restarting services; Wait for the status to change to
RUNNING before performing a dimension
CONFIGURING While in Admin mode, and Edit condition has been activated to change configuring settings; If the settings are saved, the device
should return to the RUNNING mode; If a save function has not been performed properly and the device is in the configuring mode,
perform a restart
Table 2-2. Status Messages

QubeVu Login Screen
© Rice Lake Weighing Systems ● All Rights Reserved 7
2.2.2 Restart/Reboot iDimension
Select Restart to either restart or reboot the system.
Select Restart to restart the service currently running on the device.
Select Reboot to reboot the operating system. Rebooting the iDimension Plus takes several minutes and power cycles the unit.
If USB scale is connected, turn the scale back on to perform a transaction.
Figure 2-4. Restart/Reboot Prompt
2.3 QubeVu Inspector
The QubeVu Inspector allows users to view information regarding the device, changes made to settings and long term storage
data. It is not necessary to log in to view the information available on the QubeVu Inspector tab.
Use the following steps to access QubeVu Inspector.
1. Select to access device information.
Figure 2-5. QubeVu Inspector Selection
2. Select . The QubeVu Inspector menu displays.

iDimension Plus
8 Visit our website www.RiceLake.com
2.4 Device Information
The Device Information button provides access to view the serial number, software version number and to access the
Inspector menu.
The Device Information tab displays specific information about the device.
Figure 2-6. QubeVu Inspector Device Information Tab

QubeVu Login Screen
© Rice Lake Weighing Systems ● All Rights Reserved 9
2.5 Change Log
The Change Log is a list of changes made to setting. This menu is used by the local weights and measures inspector.
Figure 2-7. Change Log
• To view using a date range – enter a Start and End date then select
• To view previous logs, select without entering a date range
• Use the arrow keys on the PC keyboard to scroll through the results; Select Download to export the log to a .csv file
Figure 2-8. Change Log Data

iDimension Plus
10 Visit our website www.RiceLake.com
2.6 Long Term Storage Log
Long term storage is necessary to satisfy particular Legal for Trade requirements in certain jurisdictions.
The measurement data stored in Long Term Storage contains all relevant information necessary to reconstruct an earlier
measurement. The stored data is protected against accidental, unintentional and intentional changes and can be authentically
traced back to the measurement which generated them.
2.6.1 Enabling Long Term Storage
Long term storage is enabled from the Measurement Settings (Section 5.3.4 on page 25).
2.6.2 Viewing Long Term Storage Data
Long term storage data is viewed from the Long Term Storage Log. The log is queried by specifying a Start and End scan ID.
To assist with this selection, the total number of entries is displayed along with the first and last scan IDs.
Figure 2-9. Long Term Storage Tab
Enter a scan ID range and select .
Figure 2-10. Long Term Storage Data
Use the arrow keys on the PC keyboard to scroll through the results. Select Download to export the log to a .cvs file.

QubeVu Login Screen
© Rice Lake Weighing Systems ● All Rights Reserved 11
2.7 Displays
The QubeVu Manager firmware provides three displays that can be used in case the application does not have access to the
USB touchscreen operator display.
1. From the QubeVu home page, select .
2. Select the display to edit.
Figure 2-11. Displays Menu
2.7.1 Operator Display
The Operator Display simulates the configuration of the Touch Screen USB display.
See the iDimension Plus Operation Manual (PN 195439) for a description of each function.
The Operator Display can be configured using the Admin/Setup Menu/Displays administrative function.
Figure 2-12. Operator Display
2.7.2 Customer Display
Customer Display can be used for applications where a visible display is required for viewing of dimensioning transaction.
The Customer Display does not provide access to any operator controls.
The Customer Display can be configured using the Admin/Setup Menu/Displays administrative function.
Figure 2-13. Customer Display

iDimension Plus
12 Visit our website www.RiceLake.com
2.7.3 Demo Display
Demo Display is intended for use during demonstrations and testing the effects of configuration changes.
The Demo Display page can be used to help the Rice Lake Weighing Systems technical support team in troubleshooting the
applications requirements.
Figure 2-14. Demo Display
Status messages are always displayed within the display screen menus. The messages displayed on screen are not
error messages.
See Section 11.0 on page 57 for displayed status, extended status and error status messages.
Zero Height Button
1. When selected, the following prompts:
Figure 2-15. Calibration Object Confirmation
For flat top scales or no scale, a calibration object is not required.
2. If a calibration object is used, select Ok to continue.
3. If a calibration object is not used, select Cancel to continue.
4. If the scale is using a ball-top or conveyor roller weight plater, place the calibration object on top of the platform.
5. Select Ok to perform a zero height.
Button Description
Scan The button manually triggers a dimension
High Resolution Scan For engineering use only
Zero Height The Zero Height button calculates the difference between the scan head and the base and defines the
background of the dimensioning area; For use when the background of the work area has changed,
the scale has shifted on the platform causing the device to provide inaccurate dimensions for the height
Table 2-3. Display Parameters
Note
Note

Operator Tools
© Rice Lake Weighing Systems ● All Rights Reserved 13
3.0 Operator Tools
This section provides an overview of iDimension Plus operator tools instructions.
3.1 Extract Data
Extract Data allows the user to view the status of the scheduled scan data extract and perform a manual export of scan data.
See Section 11.2.1 on page 60, for detailed information on configuring scan data extract.
From the main menu, select .
Select to view the status of the scheduled scan data extract or perform a manual scan data export.
Figure 3-1. Operator Tools Menu
The Extract Data menu displays the status of both the scheduled extract and the manual extract.
Select Start to perform a manual extract.
Figure 3-2. Manual Extract Display

iDimension Plus
14 Visit our website www.RiceLake.com
4.0 Admin Tools
This section provides an overview of iDimension Plus admin tools instructions.
4.1 Admin Tools Menu
Admin Tools are used for configuring, calibrating, defining, upgrading, backing up and running diagnostics on the system.
To enter the Admin Tools menu use the following steps:
1. Go to the home page.
2. Select to log in.
3. The default user name is admin and the default password is password.
4. Select desired tool.
Figure 4-1. Admin Tools Menu
Parameter Description
Setup General (operational and scale), time and date, data extraction and long term storage, measurement, network settings
Calibration Calibration settings, define work area and zone of interest, calibrate cameras (Section 6.0 on page 34)
Capture Definitions Capture definitions for QubeVu (Section 7.0 on page 43)
Firmware Upgrade Update firmware (Section 8.0 on page 45)
Backup Backup and restore settings (Section 9.0 on page 48)
Diagnostics Diagnostics settings (Section 10.0 on page 50)
Table 4-1. Admin Tools

Admin Tools
© Rice Lake Weighing Systems ● All Rights Reserved 15
4.1.1 Edit/Cancel/Save Keys
While in the Admin Tools menus, on the right side of the screen the Edit, Cancel and Save keys are active.
Figure 4-2. Edit, Cancel and Save Keys
Edit
Display while in the general setting mode and calibration menu. Prior to making changes to these settings, select Edit.
Change the settings then select Save to continue.
Cancel
Cancels all edits made to all tabs, unless saved.
Save
The Save key saves all changes made during the edit process within the page and a sub menu tab. Upon save, the unit may
restart and return to the home screen.

iDimension Plus
16 Visit our website www.RiceLake.com
5.0 Setup
This section provides an overview of iDimension Plus setup instructions.
5.1 Setup Menu
Select to enter the setup menu.
Figure 5-1. QubeVu Setup
5.2 General Settings
General setting provides access to configuring the operation of the unit, enable flat detection, configure the scale and other
external interface methods for retrieving data.
Select from the Setup menu to enter.
Figure 5-2. Setup – General Settings
Note