Rice Lake TE Series User manual

TE Series Tuning Fork Balance
Ethernet Option Installation
The Ethernet Option (PN 186079) provides an RJ-45 port for Ethernet output communication from the TE Series Balance. This
document describes the installation procedures and communication settings for the Ethernet Option.
To ensure safe and proper use of the balance, completely read this documentation and the TE Series Operation
Manual (PN 185193) before use. Store both documents in a safe place near the balance to review as needed.
Manuals and additional resources are available from the Rice Lake Weighing Systems website at www.ricelake.com
Warranty information can be found on the website at www.ricelake.com/warranties
Unpacking and Option Parts
Immediately after unpacking, visually inspect and ensure all components are included and undamaged. If parts were damaged
in shipment, notify Rice Lake Weighing Systems and the shipper immediately.
Figure 1. Ethernet Option Parts Illustration
Option Installation
Make sure that the power is disconnect before installation of the Ethernet Option.
1. Remove the screw securing the option slot cover and remove the option slot cover.
Figure 2. Remove Option Slot Cover
2. Insert the option board along the rail of the option slot until surface of the option faceplate is flush with the balance
chassis within 0.5 mm.
3. Secure the option in place with the screw previously removed.
Figure 3. Insert and Secure Option
Use LAN cable of “CAT 5” or higher. When using a non-shielded LAN cable, attach the included ferrite core
approximately 2'' from the connector.
IMPORTANT
Ethernet Option Board Removal Screw Ferrite Core
CAUTION
Note
PN 205762 Rev A
March 12, 2021

230 W. Coleman St. • Rice Lake, WI 54868 • USA
U.S. 800-472-6703 • Canada/Mexico 800-321-6703 • International 715-234-9171 • Europe [phone]
Rice Lake Weighing Systems is an ISO 9001 registered company.
© Rice Lake Weighing Systems Specifications subject to change without notice.
www.ricelake.com
PN 205762 Rev A
March 12, 2021
TE Series Balance Ethernet Option
Communication Settings
The Ethernet Option board is equipped with “Xport” manufactured by Lantronix. Refer to the External Input/Output Functions
and Communications sections in the TE Series Operation Manual (PN 185193) for information on settings and configuration.
“Baud Rate”, “Parity”, “Stop Bit”, and “Response Command” are associated to the internal communication between
the balance and the Ethernet Option, not the external communications. If these settings have been changed,
reconfigure them to the default values.
IP Address Setting
1. Download DeviceInstaller on a PC:
a. Go to the website: https://www.lantronix.com/products/DeviceInstaller/
b. Click Download Software.
c. Download the file name: Stand-alone DeciveInstaller Setup application for Windows (125 MB)
2. Install DeviceInstaller on PC.
3. Connect the balance to the network:
a. Connect the balance with the Switching Hub and power on the balance.
b. Through the PC’s Start Menu, go to “Lantronix” → “DeviceInstaller”.
c. Once DeviceInstaller is open, press F1 on the keyboard to access the DeviceInstaller Help file.
The Ethernet Option MAC address is indicated on the faceplate of the option under the port.
Communication Specifications
Connector RJ-45 (8P8C)
Interface Ethernet 10Base-TX (auto-sensing)
Version Version 2.0 / IEEE 802.3
Protocols TCP/IP, UDP/IP, ARP, ICMP, SNMP, TFTP, Telnet, DHCP, BOOTP, HTTP, Auto IP
Management Start bit Internal Web server, SNMP (read only), Serial login, Telnet login, Microsoft Windows-based utility for configuration
Security Parity bit Password protection, Optional 256-bit AES Rijndael encryption
Option Removal
Make sure that the power is disconnect before removal of the Ethernet Option.
1. Remove the screw securing the option.
2. Insert the removal screw to pull out the option from the balance.
Figure 4. Option Removal
Note
Note
CAUTION