Ricoh SH-P1 Series Installation guide

SH-P1 Training
1
Slide 1
MODEL SH-P1 TRAINING
Machine Codes: M020/M021
Version 1.0
This course is for the SK-P1 series of copiers.
Modifications
Started 22 February, 2011.
Release version -- 8 March 2011.

SH-P1 Training
2
Slide 2
Course Contents
Product Outline
Introduction
Specifications
Options
Installation
Transporting the Machine
Maintenance
Machine Overview
Paper Feed
Laser Exposure
All In One Cartridge (AIO)
Fusing
Paper Exit
Duplex
Optional Paper Tray Units
(M386, M389)
Environmental Conservation

SH-P1 Training
3
Slide 3
PRODUCT OUTLINE
Introduction
No additional notes

SH-P1 Training
4
Slide 4
Machine Concepts
Product Placement
Concepts
1. There is not a predecessor model. (New engine)
2. New AIO was developed to achieve B&W 45/50ppm.
3. User install & User maintenance.
45/50ppm
No additional notes.

SH-P1 Training
5
Slide 5
How many Models?
Two models
SH-P1a 45 ppm model
» Code: M020
» Product Names: SP5200DN, Aficio SP5200DN
SH-P1b 50 ppm model
» Code: M021
» Product Names: SP5210DN, Aficio SP5210DN
No additional notes.

SH-P1 Training
6
Slide 6
Configuration
Configuration depends on the number of optional paper feed
units.
If the printer is installed on the floor, the bottom paper feed unit
must be a TK1130 (has casters).
7
Paper feed
units TK1120
(M386)
Paper feed
unit TK1130
(M389)
Basic printer
(Includes one
paper tray)
Up to four paper feed units can be added as options with a maximum of three
TK1120 units. If installed on the floor, the lowermost paper feed unit should be
TK1130 (has casters and stabilizers).
The standard paper tray and the optional paper feed units hold 550 sheets of
paper each (80 g/m2).

SH-P1 Training
7
Slide 7
11
OptionOptionM38803SD card for NetWare printing type E
OptionOptionM38805IPDS unit type 5200
OptionOptionM352SD card for fonts type C
OptionOptionB679IEEE 1284 interface board type A
StandardOptionM385VM card type O
StandardOptionM352HDD Type 2670 (1)
StandardOptionD362Memory unit type G (256 MB)
D344
G874
D435
M389
M386
Code
OptionOptionPaper feed unit TK1130
OptionOptionIEEE 802.11a/b/g type M/L (2)
OptionOptionGigabit Ethernet board type A
StandardOptionMemory unit type I (512 MB)
OptionOptionPaper feed unit TK1120
SH-P1a (M020) SH-P1b (M021)Option
Options
This table shows the options available for this product.
(Some are standard for the SH-P1b.)
(1) Includes data overwrite security and HDD encryption.
(2) Wireless LAN – type M for Europe and Asia, type L for North America
No additional notes.

SH-P1 Training
8
Slide 8
PRODUCT OUTLINE
Specifications
This section explains the important specifications.

SH-P1 Training
9
Slide 9
Specifications 1
Print Rate
SH-P1a: 45 ppm (A4), 47 ppm (LT)
SH-P1b: 50 ppm (A4), 52 ppm (LT)
First Print Time
7.5 seconds or less (A4/LT SEF)
Warm-up Time (from main switch on)
20 seconds or less
Max Power Consumption
SH-P1a: Less than 830W
SH-P1b: Less than 900W
Max Paper Size
A4/LT
No additional notes.

SH-P1 Training
10
Slide 10
Specifications 2
Paper Feed Capacity (LT/A4, 80g/m2)
Standard Tray: 550 sheets
Optional Trays: 550 sheets each (up to 4)
Bypass tray: 100 sheets
Paper Output Capacity (LT/A4 , 80g/m2)
Up to 500 sheets
Paper Weight
Standard Tray, Optional Trays, By-pass Tray: 52-
220 g/m2, 14-59 lb
Duplex: 60-163 g/m2, 16-44 lb
Resolution
600 x 600 dpi, 1200 x600 dpi
For additional and more detailed specifications, see the FSM.

SH-P1 Training
11
Slide 11
Reliability Targets
Average print volume per month:
SH-P1a: 4K
SH-P1b: 5K
Maximum print volume per month: 15 K
Installation Time Estimation: 15 minutes
MPBF (Mean Prints Between Failure):
SH-P1a: 114 K
SH-P1b: 143 K
Machine Life: 900k or 5 years
No additional notes

SH-P1 Training
12
Slide 12
Product Outline
Options and Consumables
No additional notes

SH-P1 Training
13
Slide 13
Optional Units
Paper handling options
One TK1130 550-sheet paper feed unit (with casters)
Up to three TK1120 550-sheet paper feed units (without
casters)
Controller options
IEEE802.11a/g Type M: Same as K-P2
IEEE802.11a/g Type L: Same as K-P2
Gigabit Ethernet Type C: Same as SI-P3
Gigabit Ethernet Type A: Same as K-P2
IEEE1284 Interface Board Type A: Same as K-P2
Others
Hard Disk Drive Type 4310 (Standard on SH-P1b): Same as
SI-P3
Memory Unit Type I 512MB (Standard on SH-P1b): Same as
Z-P1
Memory Unit Type G 256MB (Standard on SH-P1b): Same
as K-P2
VM Card Type O (Standard on SH-P1b): Same as Z-P1
SD Card for Fonts Type C: Same as SI-P2
SD Card for Netware Printing Type E: New
IPDS Unit Type 5200: New
Only one option can be installed in the I/F slot.

SH-P1 Training
14
Slide 14
User Installable vs
Service Installable Options
I/F slotIEEE1284 Interface Board Type A
Controller boardMemory Unit Type I 512 MB
Controller boardMemory Unit Type G 256 MB
Controller boardHard Disk Drive Type 4310
SD cardSD Card for Fonts Type C
SD cardSD Card for Netware Printing Type E
I/F slotGigabit Ethernet Type A
zUser installable options
zService installable options
SD cardIPDS Unit Type 5210
SD cardVM Card Type O
I/F slotGigabit Ethernet Type C
I/F slotWireless LAN IEEE802.11a/g Type L
I/F slotWireless LAN IEEE802.11a/g Type M
Location
Only one option can be installed in the I/F slot.
Refer to the previous slide for information on which options are new and which
are common with other products.

SH-P1 Training
15
Slide 15
Optional Paper Trays
You can install up to four optional paper trays.
If installed on the floor, the bottom tray must be TK1130
because it has casters. Stabilizers must also be attached,
as shown below.
Stabilizer Stabilizer
No additional notes

SH-P1 Training
16
Slide 16
Slots/Plugs for Controller Options
One of three options can be installed in the I/F slot -- Wireless
LAN, Gigabit Ethernet, or IEEE 1284 interface board.
I/F Slot
LAN
SD Card Slot 1
USB (type B)
USB (type A)
SD Card Slot 2
The SD Card slots are discussed in more detail on the next few slides.
Remove the covers to access the SD card slots and I/F slot.

SH-P1 Training
17
Slide 17
SD Card Slots
Slot 1 (upper slot)
M021 only: Contains the Security SD Card when
shipped
» The Security SD Card contains the Data Overwrite
Security unit and HDD Encryption Unit.
Used for running programs
Slot 2 (lower slot)
Empty when shipped.
Contains the VM card after the machine’s
installation procedure. (Standard for M021, option
for M020)
Use this slot for service procedures, such as
firmware update and NVRAM backup.
No additional notes

SH-P1 Training
18
Slide 18
Installation
No additional notes.

SH-P1 Training
19
Slide 19
Overview
The user installs this machine.
However you should also know how to install the
machine in the event you are asked to do so in
the field.
Refer to the following user’s documents.
SH-P1 field service manual, installation section
Quick installation guide
Hardware guide
No additional notes

SH-P1 Training
20
Slide 20
Before You Start
Read the notes for the following before you
install the machine.
Environment
Space requirements
Power requirements
No additional notes.