Rielta STEKLO-3M User manual

Introduction
Glass break detector «Steklo-3M» (hereinafter, the Detector):
- is intended for detecting destruction of all known kinds of construction
glass: common, quenched, patterned, armored, multilayer and laminated
with polymer film, glass units, as well as hollow glass blocks installed in
structural units (openings) and/or interior elements of closed spaces;
- generates alarm messages by control relay contacts opening and
sends it to control panel (hereinafter, the CP);
- ensures case tamper protection by «Failure» relay contacts opening;
- may be installed on the wall, pier between windows and or ceiling.
Features
The Detector:
- ensures remote monitoring of controlled glazed structures of any
configuration in a closed area;
- provides monitoring of different types of glasses with different
dimensions;
- assures multilevel microprocessor signal processing, functional
self-testing and regular monitoring of acoustic channel;
- offers to user an opportunity to choose an algorithm of the Detector
operation in accordance with situation on the secured object or with
chosen security tactics;
- displays modes of operation of the detector and noises inside the
protected closed area by means of LED indication (providing possibility
of noise and alarm indication disabling);
- operates in temperature range from minus 20 up to + 45 0С, DС
power supply range 9 … 17 V.
Scope of Delivery
Each Detector unit package contains the items listed in tn Table 1.
Table 1
Name QNT
Glass break detector «Steklo-3M»
Testing ball
Screw 3-3х30.016
Glass break detector «Steklo-3M». Installation Guide
1 pc.
*
2 pcs.
1 copy
* – Supplied optionally
Field of Application
The Detector can be applied in offices, shops, museums, exhibition
halls, banks, accommodation rooms, etc.
Choosing Place of Installation
Before installing the Detector, get acquainted with the following
requirements:
- when choosing the place of installation, the Detector detection zone
location must be taken into account (Figure 1);
- it is recommended to install the Detector at a height not less than
2 m (see examples of installation in Figures 4 – 8);
- during joint operation with an active ultrasonic Detector, distance
between Detectors must be not less than 1 m;
- entire area of protected glass should be available to the Detector
visibility zone;
- distance (L) from the detector to the farthest point of protected area
should not exceed 6 m. If protected glass area is more than 1 m2, the
specified distance L should be lengthened up to 9 m.
- for protection of quenched, laminated, armored, multilayer or
small-area glasses, universal operation mode (See Table 2) should be
chosen.
GLASS BREAK
DETECTOR
«STEKLO-3M»
Adjustment and Testing
Set DIP-switches «1», «2» and «5» in ON position. Energize the
Detector, whereupon the red LED indicator («Alarm» message indication)
should light during 2 – 10 sec and go out, displaying that the Detector
is turned to the standby mode.
Estimate interference conditions inside protected area. Yellow LED
indicator lighting is an evidence of high-frequency noises presence,
green LED lighting – of low-frequency ones. If it is possible, eliminate
source of noises.
Fulfill the Detector adjustment as follows:
- set DIP-switches «1» and «2» in OFF position, «6» in ON position,
«3» and «4» in OFF position;
- suspend a steel ball 20 – 22 mm in diameter on a 30 … 35 cm
long thread, press free end of it to the upper side of a glass structure
(ordinary, ornamental, armored, laminated), deflect it at an angle of
30 – 700 (see Table 3, for hollow glass blocks – 45°). Deliver a blow,
whereupon the Detector should generate an alarm message. If there
is no red LED lighting after test blows (relay contact are not opening),
the Detector sensitivity should be increased by DIP-switches «1» and
«2» (see Table 2);
Table 3
Glass thickness, mm <3 3...4 4...5 5...6 6...7 >7
Ball deflection angle for ordinary,
armed and ornamental glass, 030 35 40 45 50 55
Ball deflection angle for,
hardened and laminated glass, 045 50 55 60 65 70
- for the Detector adjustment for multilayer glass or small area of glass
protection, it is allowed to use electronic glass break simulator during
adjustment;
- check the correctness of the Detector adjustment with the Detector
cover installed;
- after completing the Detector adjustment, set DIP-switch « 6 » to OFF
position and choose the mode of operation by « 3 » , « 4 » and « 5 » DIP-switches
(see Table 2) in accordance with type of secured glass and security tactics
accepted for the object.
Manufacturer’s Guarantees
The manufacturer guarantees conformity of the Detector to the
Technical Specifications requirements provided the transportation,
storage, installation and operation conditions are observed.
The guaranteed shelf life of the Detector is 63 months since the date
of manufacture.
The guaranteed useful life is 60 months since the day of putting into
operation within the guaranteed shelf life.
The Detectors that are found non-conforming to the Technical
Specifications requirements shall be repaired by manufacturer, provided
the installation and operation rules have been complied with.
Table 2
DIP-switch position Detector Operating Mode
123456
OFF
OFF
ON
ON
OFF
ON
OFF
ON
Sensitivity
(detection
range)
adjustment
minimum
+6 dB
+14 dB
+20 dB (maximum)
OFF
ON
Universal mode
Detection of glass destruction with
chip fallout
OFF
ON
Alarm memory
indication
– OFF
– ON
OFF
ON
LED indication
control
– OFF
– ON
OFF
ON
Standby mode
Adjustment
–
LED indicator
lighting green
Installation
Choose the Detector place of installation, mark out places for fastening.
Remove cover and fasten the Detector by screws.
The Detector Connection
Fulfill the Detector connection in accordance with Figures 2 or 3.
Figure 2 – The Detector
connection pattern with separate
alarm and case tamper loops
Figure 3 – Detector connection
pattern of combined alarm and
case tamper loops
Power
supply
+ –
CP
AL1 AL2
AL +12V- Tamper
Installation Guide
Power
supply
+ –
CP
Figure 1 – GB channel detection pattern
Top view
Side view
AL
AL +12V- Tamper

Acceptance and Packing Certificate
Glass break detector «Steklo-3M»,
lot number________________________ ,
has been manufactured in compliance with the active technical documentation, classified as fit for operation and packed by «RIELTA» JSC.
Person in charge of acceptance and packing
QC representative___________________________ _________________________.
month, year
Rev.3 of 27.12.16
№ 00200
Made in Russia
«RIELTA» JSC, www.rielta.com
Chapaeva Str. 17, Saint Petersburg, Russia, 197101, [email protected]
Tel./fax: [phone],
Technical support, tel. [phone], [email protected]
Figure 4 – Installing the Detector
on the Ceiling
Detector
max. 6 m
Detector
Figure 6 –Installing the Detector on the
Opposite Wall
Figure 5 – Installing the Detector on
a Side Wall
min. 2 m
max. 6 m
Detector
max. 6 m
min. 2 m
Detector
min. 2 m
max. 6 m
min. 2 m
Figure 9 – Unauthorized Detector
Installation Places
Detector
max. 6 m
Figure 8 – Detector Installation
between the Glass and the Curtains
(Blinds) or on a Window Frame
Figure 7 – Installing the Detector on
the Ceiling (for window openings in the
neighboring walls monitoring)
Detector
max. 6 m
Examples of the Detector Installation
Figures 4 – 8 illustrate correct variants of the Detector installation, Figure 9 displays the wrong ones.