Rielta FOTON-15A User manual

4
1
3
2
7
11
8
9
10
5
612 13 14
15
1718
16
Installation Guide
PASSIVE INFRARED
LONG RANGE
DETECTOR
«FOTON-15A»
1 General Information
Passive infrared long range detector «Foton-15A» (hereinafter, the
Detector) is designed for detecting intrusion into a protected space and
generating an alarm message by consumption current value changing.
The Detector can be installed in heated or unheated spaces having
different application: in museums, offices, cottages, flats, shops, as
well as in warehouses, garages, hangars.
The Detector generates three types of messages:
- «Norm»;
- «Alarm»;
- «Tamper».
The Detector provides digital temperature compensation of it’s
detectability.
2 Features
- Dual-element pyrodetector;
- Power supply by the alarm loop (AL);
- Immunity to insect’s intrusion to the pyrodetector;
- Swivel bracket (supplied) providing ease of Detector installation
and detection zone repositioning;
- LED indicator for the Detector operation visual control. LED
indication is switched ON or disabled by applying a jumper to one of
the «IND» wafer position («ON» or «OFF»);
- Two modes of alarm messages generation: «Short-circuit» (SC)
(by increasing current consumption value) and «Open-circuit» (OC)
(by decreasing current consumption value). Required operation mode
is assigned either by removal SC jumper, or by applying OC jumper to
the «OC» wafer position.
3 Principal Technical Characteristics
Table 1
Parameter Value
Detection zone types long range
Maximum detection range, not less than 20 m
Detection angle in horizontal plane 60
Mounting height 2.3 m
Detected speed range 0.3 – 3 m/sec
Alarm message duration, not less than 2 sec
Warm-up time, not more than 60 sec
Power supply 8 – 72 V DC
Current consumption in «NORM»mode:
SC mode, not more than
OS mode, adjustable
0.1 mА
2 ... 15 mА
Operation temperature minus 30 ... +50 0С
Relative humidity under 25 °С without moisture
condensation 95 %
IP rating IP41
Dimensions, maximum 126 х 70 х 55 mm
Mass, not more 0.15 kg
4 Detection Zone Pattern
5 Scope of delivery
Each Detector unit package contains the items listed in Table 2.
Table 2
Name QNT.
Passive infrared long range detector «Foton-15A»
Swivel bracket
Screw 3-3х30.016
Passive infrared long range detector «Foton-15A».
Installation Guide
1 pc.
1 pc.
2 pcs.
1 copy
6 The Detector Design
The Detector comprises base, printed circuit board (PCB) and a
cover. Swivel bracket is included in scope of delivery.
1 – bush;
2 – nut;
3 – sphere;
4 – swivel bracket case;
5 – openable holes for wiring;
6 – openable hole for fastening to swivel bracket;
7 – screw;
8 – openable holes for corner mounting;
9 – opening for cover holder;
10 – PCB fixing arm;
11 – openable holes for wall mounting;
12 – leading-in sockets for AL plugging;
13 – LED indicator;
14 – LED indication ON/OFF jumper;
15 – Operating modes changeover SC/OP jumper;
16 – potentiometer for current consumption adjustment;
17 – pyrodetector;
18 – case ramper.
Figure 2 – Design of the Detector
7 Choosing Place of Installation
When choosing the Detector installation place, take note of the fact
that the detection zone may be limited by non-transparent objects
(curtains, houseplants, cabinets, bookcases, etc.), as well as glass and
mesh partitions. There must be no windows, air conditioners, space
heaters or heating radiators in the Detector visibility range.
When mounting choose the Detector orientation in such a position,
that any potential directions of intrusion should cross sensitive zones
of the Detector.
Power supply and alarm loops should be wired far enough from load
cables. There must be no animals or birds in the protected space.
8 The Detector Installation
Choose the place of installation (Cl. 7):
- unfasten the latch through the opening, which is situated downside
the detector case by means of screwdriver and put off the detector
cover (Figure 2);
- when installing the detector without swivel bracket it is necessary
to put off the PCB by means of pushing up it’s fixing arm;
- drill the holes in the base of the detector for wiring and fastening
the detector;
- choose the place of installation, mark the places for mounting
holes with the regard to detector base (or swivel bracket) openings;
- drill the holes in the wall with regard to market places;
- pass the wire through the mounting holes in the base, leaving
several centimeters of installation wire for it’s fastening inside the case;
- fix the base of the detector case on the wall (swivel bracket) at
the chosen place. In case of swivel bracket using, unscrew the cap
screw from the swivel bracket sphere. Fit the square bulge of the swivel
Figure 1 – Detection Zone Pattern
Structure of any
sensitivity zone
60
20 m
20 m
2.3 m1 m

Rev.1 of 10.11.14
№00085
bracket external sphere with the corresponded opening on the detector
base. Plug in the screw to the opening in the top of the detector base
and fix connection by the screw;
- put PCB on it’s place, plug loop wirings in accordance with Cl. 9;
- close the cover.
9 Variants of the Detector Connection
10 Functional Testing
- Energize the Detector and wait for 60 – 70 sec before functional
testing performance.
- Start walking through the detection zone. After movement detection,
« Alarm » message is displayed by LED indication of the Detector. The
Detector must reveal a human, moving at a speed 0.3 … 3 m/sec after
3 – 4 steps within the detection zone limits. Upon the movement
absence in the protected space, « Alarm » message should not been
generated.
ATTENTION! The Detector must be checked at least annually in
order to test it’s performance.
11 Transportation and Storage
11.1 The Detectors in their original packing may be shipped by any
transport means in covered vehicles (in railway, cars, trucks, sealed
heated compartments of aircraft, ship cargo holds, etc). The storage
room should be free from current-conducting dust, acid vapors, alkali
and gases that cause corrosion and destroy insulation
11.2 The Detectors in their original packing may be stored not more
than 3 months. During this period the Detector package should not
have bloodshot spots and impurities.
11.3 Upon the expiry of 3 months, the Detector should be released
from the package.
12 Manufacturer’s Guarantees
The Manufacturer guarantees conformity of the Detector to it’s
Technical Specifications if conditions of transportation, storage,
assembling and operation are observed. The guaranteed storage period
is 63 months since the date of manufacturing the Detector.
The guaranteed period of operation is 60 months since the date of
commissioning within the storage period guaranteed.
The Detectors that are found to non-conforming to it’s Technical
Requirements shall be repaired by the Manufacturer, provided the
installation and operation rules have been complied with.
13 Acceptance and Packing Certificate
Passive infrared long range detector «Foton-15A» ,
serial number ____________,
has been manufactured in compliance with the active technical
documentation and classified as fit for operation and packed by
« RIELTA » JSC.
Person in charge of acceptance and packing
QC representative_________________ __________________.
day, year, month
If connection of the Detector to the loop is fulfilled in parallel to
terminal element (Figure 3a), you should preliminarily set the alarm
current value with allowance for the real load-carrying capacity of the
loop. For this purpose act as follows:
- apply an OS jumper on the wafer located on the Detector PCB;
- fulfill connection of the Detector to the loop and energize it;
- make sure, that control panel (hereinafter, CP) got an alarm signal,
and input voltage value on AL contacts remains not less than 8 V;
- if value of input voltage on AL contacts is less than 8 V, then using
the potentiometer slider set value of consumption current, at which
input voltage value on AL contacts remains not less than 8 V, and CP
registers an alarm message;
- remove OS jumper on the PCB and check the Detector operability
according to the method described in the following chapter.
Take a note that the loop resistance with allowance for summary
current consumption of the Detector in standby mode and current
let-through the EOL resistor should be in the limits, which the CP
identifies as « Norm » . Adjustment of alarm value OS fulfilled by means
of potentiometer consequently in turn for each Detector while OS
jumpers at other Detectors are removed.
When the Detector is hooked up to the loop instead of a terminal
(EOL) element (Figure 3b), Adjust by « current » potentiometer such a
value of useful current in standby mode, that provides the same voltage
on AL contacts as on EOL element loop.
ATTENTION! If the Detector is planned to be in use with disabled
indication, then adjustment should be fulfilled with the indication
disabled.
Figure 3 – Connection Pattern
а) In parallel to terminal EOL element - SC mode
b) Instead of EOL resistor - OC mode
AL
AL
Tamper -AL+ -AL+
EOL
resistor
Tamper
Tamper AL
Tamper -AL+ -AL+
Tamper -AL+ -AL+
«RIELTA» JSC, www.rielta.ru,
Chapaeva Str. 17, Saint Petersburg, Russia, 197101, [email protected],
Tel./fax. [phone],
Technical support, tel. [phone], [email protected].