Rimage DL5200 User manual

Rimage DL5200/DLN5200
User Guide

Corporate Headquarters:
Rimage Corporation
7725 Washington Avenue South
Minneapolis, MN 55439
USA
800-553-8312 (toll free US)
Service: [phone] (International)
Fax: [phone]
European Headquarters:
Rimage Europe GmbH
Albert-Einstein-Str. 26
63128 Dietzenbach Germany
Tel: [phone]
Fax: [phone]
Rimage Corporation reserves the right to make
improvements to the equipment and software described
in this document at any time without any prior notice.
Rimage Corporation reserves the right to revise this
publication and to make changes from time to time in the
content hereof without obligation of Rimage Corporation
to notify any person or organization of such revisions or
changes.
This document may contain links to web sites that were
current at the time of publication, but may have moved or
become inactive since. This document may contain links
to sites on the Internet that are owned and operated by
third parties. Rimage Corporation is not responsible for
the content of any such third-party site.
©2007, Rimage Corporation
Rimage™ is a trademark of the Rimage Corporation.
DL5200/DLN5200™ is a trademark of the Rimage
Corporation. Dell®is registered trademark of Dell
Computer Corporation. FireWire®is a registered
trademark of Apple Computer, Inc.
All other trademarks and registered trademarks are the
property of their respective owners.
110768-000_F

Contents
Introduction..............................................................................................................1
Important Information..............................................................................................2
Support Information..........................................................................................................................2
Learn More Online ...........................................................................................................................2
Technical Support and Product Updates.........................................................................................3
CD and DVD Recording Software Disclaimer..................................................................................3
Safety and Compliance Information.................................................................................................3
Safety Precautions....................................................................................................................................3
Compliance Information............................................................................................................................4
DL5200/DLN5200 Specifications.....................................................................................................5
Identify the Parts of the Rimage DL5200/DLN5200...............................................7
Front View........................................................................................................................................7
Rear View - Rimage DLN5200.........................................................................................................8
Rear View - Rimage DL5200...........................................................................................................8
Description of Parts..........................................................................................................................9
Operator panel..........................................................................................................................................9
Operator button.........................................................................................................................................9
Beeper......................................................................................................................................................9
Output trays..............................................................................................................................................9
Output bin...............................................................................................................................................10
Operate the Rimage DL5200/DLN5200.................................................................11
Power On.......................................................................................................................................11
Power on the Rimage DLN5200.............................................................................................................11
Power on the Rimage DL5200................................................................................................................11
Power Off.......................................................................................................................................12
Power off the Rimage DLN5200.............................................................................................................12
Power off the Rimage DL5200................................................................................................................12
Load Discs .....................................................................................................................................12
Remove or Install the Front Panel .................................................................................................13
Remove the front panel ..........................................................................................................................13
Install the front panel ..............................................................................................................................13
Maintain the DL5200/DLN5200..............................................................................15
Preventive Maintenance Schedule ................................................................................................15
Align the Everest Printer ................................................................................................................15
Operate Gemini Utilities.................................................................................................................18
Start Gemini Utilities...............................................................................................................................18
Change the autoloader display name.....................................................................................................18
Enable the beeper ..................................................................................................................................18
Stop Gemini Utilities ...............................................................................................................................18
110768_F i

Introduction
Introduction
This manual provides the information needed to operate the DL5200/DLN5200 and identify the parts. To set
up and install your DL5200/DLN5200, refer to the Setup and Installation Guide included with your product.
The Rimage DLN5200 and DL5200 are robotic-controlled
autoloaders containing two recorders, a two-line display panel,
and an Everest™ printer. The Rimage DL5200/DLN5200
records and prints discs, then places the finished discs in the
output bin, or in one of the five output trays.
The Rimage DL5200 requires a PC.
The Rimage DLN5200 has an embedded PC and is a network
ready device that receives orders from other networked
computers. You can also operate the Rimage DLN5200 by
attaching a monitor, keyboard, and mouse.
Rimage DL5200/DLN5200
110768_F 1

Rimage DL5200/DLN5200 User Guide
Important Information
This section provides support contact information, cautions and warnings, and product specifications for the
DL5200/DLN5200.
Support Information
US, Asia/Pacific, Mexico/Latin America Europe
Rimage Corporation
7725 Washington Avenue South
Minneapolis, MN 55439
USA
Attn: Rimage Services
Rimage Europe GmbH
Albert-Einstein-Str. 26
63128 Dietzenbach Germany
Contact Rimage Services:
www.rimage.com/support.html
Email: http://www.rimage.com/support_form.cfm
Telephone:
North America: 800-553-8312
Asia/Pacific, Mexico/ Latin America: 952-946-0004
Fax: [phone]
Contact Rimage Services Europe:
www.rimage.com/support.html
Email: [email protected]
Telephone: [phone]
Fax: [phone]
When you contact Rimage Services, please
provide: My Rimage Product Information:
Copy this information from your Rimage Product for future
reference.
•Unit serial number and software version. Serial Number:
•Functional and technical description of the problem. Product Name:
•Exact error message received. Date of
Purchase:
Learn More Online
At www.rimage.com/support.html, you can experience Rimage’s world-class Support and Services.
1. Select your product family. 2. Select your product. 3. Learn more on your product
page.
From your product page you can access:
yInformation about the latest software and firmware updates
yProduct specifications
yThe latest documents
yCurrent firmware and driver downloads
2 110768_F

Important Information
Technical Support and Product Updates
Support for the DL5200/DLN5200 is available through your authorized reseller.
-Important! Be sure to register your DL5200/DLN5200 so Rimage can notify you of upgrades as they
become available.
nuipment.
nve this guideline could result in loss or damage to the
the precautions in this document and familiarize yourself with their meaning
efore using the equipment.
nWar
•rmful to
•instrument in conjunction
to
Use the supplied AC power cord, or use a safety
agency-approved power cord.
•
•
battery according to the manufacture’s
instructions included with the battery package.
CD and DVD Recording Software Disclaimer
This Product, Software, or Documentation may be designed to assist you in reproducing material in which
you own the copyright or have obtained permission to copy from the copyright owner. Unless you own the
copyright or have permission to copy from the copyright owner, you may be violating copyright law and be
subject to payment of damages and other remedies. If you are uncertain about your rights, you should
contact your legal advisor. If you are neither in possession of the copyright nor have authorization from the
owner of the copyright, unauthorized copying of CDs and DVDs violates national and international legislation
and can result in severe penalties.
Safety and Compliance Information
Safety Precautions
This manual and the indications on the product allow proper and safe operation. The indication marks below
help protect you and other persons from injury, and equipment from damage.
Warning! According to ANSI (American National Standards Institute) standards, a warning is used to
indicate situations that could result in bodily injury to personnel operating or maintaining the eq
Caution: Indicates that failure to obser
equipment, product, software, or data.
To ensure safety, please read
b
ning:
The laser beam used by this CD-R or DVD-R
recorder is a class 1 laser and can be ha
the eyes. Do not attempt to open the recorder.
Do not attempt to view the laser beam.
Never use any optical
with this unit. To do so will greatly increase the
hazard to your eyes.
•Please observe all warning and caution labels
ensure safety of personnel.
•Replace all fuses with the same voltage and
current ratings to maintain UL safety approvals.
•
nCaution:
Any equipment that has AC line voltage, or low
DC voltages, such as switches, power supplies,
fuses, fans, non-stepper motors, must be
replaced with Rimage–approved components to
maintain the safety approval issued by UL.
The DLN5200 model contains a lithium battery.
There is a risk of explosion if the battery is
replaced by an incorrect battery. Dispose the old
110768_F 3

Rimage DL5200/DLN5200 User Guide
Compliance Information
Product name: DL5200/DLN5200
Model: DLN5200: RAS15E
DL5200: RAS15
Notice for USA
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when this equipment is operated in a commercial
environment. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference, in which case the user will be required to correct the interference at his own expense.
This product complies with UL 60950-1, 1st Edition.
Notice for Canada
This Class A digital apparatus complies with Canadian ICES-003 Issue 4:2004. Cet appareil
numerigue de la classe A est conforme a la norme NMB-003 du Canade.
This product complies with CAN/CSA-C22.2 No. 60950-1-03
Notice for Europe
This product is in conformity with the EMC Directive (89/336/EEC) and the Low-Voltage Directive
(73/23/EEC) through compliance with the following European standards: EN 55022: 2006;
EN 55024: 1998 +A1:2001 +A2:2003; EN6100-3-2:2000 +A2:2005; EN 61000-3-
3:1995 + Amd 1: 2001 +A2:2005; IEC 60950-1 (2001). The CE mark has been affixed in
accordance with the CE Marking Directive 93/68/EEC.
Notice for Japan
This is a Class A product based on the standard of the Voluntary Control Council for Interference by
Information Technology Equipment (VCCI). If this equipment is used in a domestic environment,
radio interference may occur, in which case, the user may be required to take corrective action.
Translation:
この装置は、情報処理装置等電波障害自主規制協議会（ＶＣＣＩ）の基準に基づくクラス
A情報技術装置です。この装置を家庭環境で使用すると電波妨害を引き起こすことがありま
す。この場合には使用者が適切な対策を講ずるよう要求されることがあります。
Notice for Australia
This product complies with AS/NZS CISPR22:2006.
4 110768_F

Important Information
DL5200/DLN5200 Specifications
Note: For printer specifications, refer to your Printer User Guide.
Standard system Rimage DL5200 autoloader, an Everest printer, and Rimage software.
Rimage DLN5200 autoloader, an Everest printer, a network-ready embedded PC, and Rimage
software.
Rimage DL5200 Rimage DLN5200
Number of Recorders 2 2
Software
requirements DL5200: Pentium 4 2.8 GHz, 512MB L2 Cache , 800MHz FSB
512MB DDR2-200, 400Mhz Bus
Microsoft Windows® 2000 Professional Service Pack 4, Microsoft Windows XP Professional
Service Pack 1or 2, Windows Server 2003
Rimage recommends 4 hard drives – One for the OS, one for the Rimage System Folder, and
two for caching (one for each recorder).
One open PCI slot for the provided FireWire®/USB card.
Ships with the correct software installed on the embedded PC. Operate only with the Rimage
software installed on the embedded PC.
DLN5200: Celeron D 340 processor with 533Mhz Front Side Bus
512MB DDR2-400, SDRAM
Windows XP Embedded with Service Pack 2
Two 36 GB, Serial ATA, 10,000 RPM, 8 MB cache, Hard Drives
Operates only with the Producer Software Suite.
Input bin capacity One removable 50-disc bin.
Output capacity Five single-disc output trays and one 75-disc output bin.
Physical size
DL5200 DLN5200
Height 23.25 inches (59.1
cm) 23.25 inches (59.1 cm)
Width* 14.5 inches (36.8 cm)
14.5 inches (36.8 cm)
Depth** 23.5 inches (59.1 cm)
23.5 inches (59.1 cm)
Weight 44.5 lbs (20.2 kg) 51 lbs (23.2 kg))
Weight with
Everest 88.5 lbs. (40.2 kg) 95 lbs. (43.2 kg))
* Allow an additional 2.4 inches (6.1 cm) of space for the door to swing open.
** Leave an additional 3.5 inches (9 cm) for cabling.
Supported
operating systems DL5200: Microsoft Windows® 2000 Professional Service Pack 4, Microsoft Windows XP Professional Service Pack 1or 2, Windows Server 2003.
DLN5200: The DLN5200 has an embedded operating system. The DLN5200 and software will
function only with the embedded operating system.
Power 100 – 240VAC, 60/50 Hz, 4.7 – 3.7 Amps
Temperature and
humidity Operating Temperature 60° to 80º F (15.5º to 26.7°
C)
Humidity
40% to 80% non-condensing Storage Temperature 5° to 95° F (-15° to 35° C)
Networking ability Refer to the Rimage Advanced Setup Guide for instructions on submitting orders from a
networked computer.
Media
requirements Refer to your printer user guide for the correct media requirements. Rimage Media Kits™ are designed for optimum recording and print performance.
110768_F 5

Rimage DL5200/DLN5200 User Guide
Specifications cont:
Ribbon
requirements Refer to your printer user guide for the correct printer ribbons. Rimage Media Kits™ include the
required print ribbons.
Label design
requirements Refer to your printer user guide for label design requirements.
6 110768_F

Identify the Parts of the Rimage DL5200/DLN5200
Identify the Parts of the Rimage DL5200/DLN5200
This section describes the Rimage DL5200/DLN5200 hardware and its features.
Front View
Operator
Button
Printer Operator
Panel
Printer
Output
Trays
Lift Arm
Recorders
Output Bin
Input Bin Supply Door
PC Power
Button
(DLN5200
only)
110768_F 7

Rimage DL5200/DLN5200 User Guide
Rear View - Rimage DLN5200 Printer USB Cable
Printer Cable
Printer Power Cord
Serial Cable
PC Power Cord
Mouse Cable
(if using) Network
Connection
Keyboard Cable
(if using)
Power Cord
Power Switch
Monitor Cable
(if using)
USB cable
Rear View - Rimage DL5200
Printer Cable Printer USB Cable
Printer Power Cord
Printer Cable
USB Cable
FireWire Cable
Power Cord
Power Switch
Note: The 9-Pin serial connector is not used.
8 110768_F

Identify the Parts of the Rimage DL5200/DLN5200
Description of Parts
Operator panel
The operator panel has a two-line display that
informs you of operations or any conditions that
require operator intervention.
The Rimage DLN5200 displays the name of the
embedded PC or product name after it initializes.
The computer name is displayed by default. This is
helpful in identifying the embedded PC on the
network. Refer to the Operate Gemini Utilities
section on page 18 to see other options.
Operator Panel
Operator button
The operator button is a push button used to open
and close the print drawer. The operator button is
only accessed by removing the front panel.
Press the operator button to open the print
drawer. Press it again to close the print drawer.
Operator Panel
Operator Button
Beeper
The Rimage DL5200/DLN5200 has a beeper that sounds when user intervention is required. Read the
condition on the operator panel or at the client application and take appropriate action to correct the
problem. To stop the beeping, open the supply door.
To change the number of beeps or to disable the beeper, refer to the Enable the beeper section on page 18.
Output trays
The Rimage DL5200/DLN5200 is configured with
five output trays and an output bin. When a disc is
recorded and printed, the lift arm moves the disc to
the output bin or one of the output trays. The disc
slides out to the end of the tray. The sensor located
on each output tray detects if a disc is in the output
tray. The output trays are numbered 1 - 5, with 1
located at the top.
Output
Trays
110768_F 9

Rimage DL5200/DLN5200 User Guide
Output bin
The output bin receives completed and/or failed
discs. The output bin holds up to 75 discs.
•To remove discs from the output bin, hold the
output bin with one hand while moving the bin latch
up and then lower the bin.
Note: Each time you fill the input bin,
remove the completed discs from the
output bin so the output bin does not
become full.
•To raise the output bin into position, lift the output
bin and then pull the bin latch down to lock it in
place.
nCaution: Do not use the latch to raise the
output bin!
Output Bin
Bin Latch
10 110768_F

Operate the Rimage DL5200/DLN5200
Operate the Rimage DL5200/DLN5200
Power On
Before you begin:
Set up the Everest printer. For more information, refer to the Rimage Everest Printer™ setup guide.
Power on the Rimage DLN5200
1. Ensure the PC power switch is in the on
position.
PC Power
Switch
2. Press the main power switch on the rear of the
autoloader to power on the autoloader.
Note: After powering on the autoloader, the
printer initializes.
Power Switch
3. Press the PC power button on the front of the
autoloader to power on the embedded PC.
When the DLN5200 autoloader has completed
the initialization, the operator panel displays
RIMAGE DLN5200 READY.
PC Power
Button
Power on the Rimage DL5200
Before powering on the computer attached to the DL5200,
power on the DL5200 by pressing the main power switch.
When the DL5200 autoloader has completed the initialization,
the operator panel displays RIMAGE DL5200 READY.
Power Switch
110768_F 11

Rimage DL5200/DLN5200 User Guide
Power Off
Power off the Rimage DLN5200
1. Close all open applications.
2. Briefly press the PC power button to shut down the software,
Windows, and the embedded PC.
nCaution: Do not press and hold the PC power button. If
you press and hold the PC power button, the embedded
PC will not shut down properly. This may cause data loss
or corruption.
Note: Powering off the DLN5200 takes approximately 30
seconds.
3. When the PC has powered off, press the main power switch
to power off the DLN5200.
Power off the Rimage DL5200
PC Power Button
1. Close all applications.
2. s
Pre s the main power switch to power off the Rimage DL5200.
Note: When you start the Rimage DL5200 again, you must first pow
er on the DL5200 and then
power on the attached computer so the recorders are recognized.
Load Discs
The input bin holds up to 50 discs. Use the
recommended Rimage media with the Everest
printer.
1. Open the supply door.
2. Remove the input bin.
Supply
Door
12 110768_F

Operate the Rimage DL5200/DLN5200
3. Place the discs in the input bin with the
recording side facing down.
-Important! Hold the discs by the edge.
Fingerprints affect print quality.
4. Place the input bin on the base plate.
5. Rotate the input bin until it drops into the
notches.
6. Close the supply door.
Remove or Install the Front Panel
Remove the front panel
Grasp the sides of the front panel and pull out.
Note: The front panel has four pins
that are held in with retaining clips.
Input Bin
Base Plate
Notch
Front Panel
Install the front panel
Align the pins to the retaining clips and press into
place.
110768_F 13

Maintain the DL5200/DLN5200
Maintain the DL5200/DLN5200
The procedures in this section will help keep your DL5200/DLN5200 in optimum operating condition.
Preventive Maintenance Schedule
Maintenance Procedure Schedule
Cleaning the Rimage
DL5200/DLN5200 Once a week. Using a damp, lint free cloth, remove dust from the
autoloader and surrounding work area.
Aligning the Everest printer On installation and as needed. Refer to the instructions below.
Align the Everest Printer
When the Everest printer is installed or replace, you may need to align it to the lift arm.
#Tools Needed: Torx T25 driver
Before you begin:
Power on the Rimage DL5200/DLN5200 autoloader. Wait for the unit to initialize.
Note: The Everest printer takes 2 to 3 minutes to complete the initialization.
1. Select Diagnostic test 4 - jog lift diagnostic.
a. Press and hold the operator button to place the unit in diagnostics mode. The operator panel
indicates when to release the button.
b. When the operator panel displays 01 CYCLE OUTPUTS DIAGNOSTIC, press the operator button
four times and hold on the fourth press. This selects the JOG LIFT DIAGNOSTIC TEST. The lift
arm moves down toward the print drawer as the printer tray opens.
c. When the operator panel prompts you to place a disc, place a disc on the print pad.
2. Check the printer alignment.
a. Press the operator button to move the
lift arm closer to the print pad.
b. Press the operator button again and the
lift arm moves down and picks up the
disc.
Lift Arm
Disc
Print Pad
Printer Tray
110768_F 15

Rimage DL5200/DLN5200 User Guide
c. Manually rotate the lead screw
counterclockwise to move the lift arm
down to the print pad.
Print Pad
Lead Screw
3. Check the disc alignment.
To see if the disc is centered, observe the
gap between the edge of the disc and the
raised edges as shown by the arrows.
If the disc requires side to side alignment,
continue to step 4.
If the disc requires front to back alignment,
continue to step 5.
4. If necessary, perform a side to side
alignment.
a. Loosen the two side to side alignment
screws.
b. Slide the printer until the side gaps are
equal.
-Important! Slide the entire printer,
not the printer tray.
c. Tighten the two side to side alignment
screws.
5. If necessary, perform a front to back
alignment.
a. Turn the front to back alignment screw
until there is a 1/16” (1.5mm) gap
between the front edge of the disc and
the raised edge of the disc retainer.
Tip: You can use the Torx T25
driver, or 5/32” Allen wrench, to turn
the front to back alignment screw.
Front to Back Alignment Screw
Side to Side Alignment Screws
Disc Retainer
Gap Distance
16 110768_F

Maintain the DL5200/DLN5200
b. When the printer is aligned, rotate the
lead screw to raise the lift arm up about
1.0” (2.5 cm).
Lift Arm
Print
Pad
Lead
Screw
6. Exit the diagnostic test.
a. Press and hold the operator button to exit diagnostic test 4. The disc is lifted up to the top output
tray and released.
b. Press the operator button fourteen times and hold on the last press to exit diagnostics.
c. Press the operator button one time to close the printer tray.
110768_F 17

Rimage DL5200/DLN5200 User Guide
Operate Gemini Utilities
The Rimage Producer Software Suite includes an application called Gemini Utilities, which is used to update
the autoloader firmware. It may also be used to change the display name of the Rimage DL5200/DLN5200
and to enable the beeper. The Rimage DLN5200 displays the computer name on the operator panel. The
computer name is helpful when identifying the computer on the network.
Tip: To access Gemini Utilities on a DLN5200, use the remote desktop connection from a networked
PC, or connect a monitor, keyboard, and mouse to the DLN5200.
Start Gemini Utilities
1. Close all applications.
2. In Rimage Service Manager, stop all Rimage
Services.
Note: Refer to your Rimage Software online help
for additional information.
3. Navigate: Start > Programs > Rimage > Utilities >
Gemini Utilities. Gemini Utilities opens.
Note: When the desired tasks are complete,
restart the Rimage Services.
Change the autoloader display name
Use Gemini Utilities to enter the name displayed on the operator panel.
1. Select the Override Name checkbox.
2. Clear the Use Computer Name checkbox.
3. In the Display Name field, enter the new name.
4. Select Set DiscLab Params to save the settings.
Enable the beeper
You can change the number of beeps that occur when there is an error.
1. In the # of Beeps on Fault field, select or enter the number of beeps you wish to hear when there is an
error.
Tip: Entering 0 (zero) in the # of Beeps on Fault field disables the beeper.
2. Select Set DiscLab Params to save the settings.
Stop Gemini Utilities
Select Exit to close Gemini Transporter Utilities.
18 110768_F