RINGFEDER GWE 5102 User manual

Partner for Performance www.ringfeder.com
C
E
A
D
B
HG
03.2020
F
Assembly, Disassembly
Elastomer Jaw Couplings
RINGFEDER®GWE
GWE 5112
Fastening: Outer cone
GWE 5106
Fastening: Split clamping hubs
GWE 5107, GWE 5117
Fastening: Clamping hub/expanding mandrel
GWE 5102
Fastening: Radial set screw hubs
GWE 5103, GWE 5103.1, GWE 5104
Fastening: Clamping hubs
GWE Z5104.1
Fastening: Clamping hubs
GWE Z5106.1
Fastening: Split clamping hubs
EN
GWE 5113
Fastening: Clamping hubs

03.2020 2
TA!
!
L5
H3
C1/ K1
EN
Used lubricants
Legend
Assembly Disassembly Cleaning
Attention!
Absolutely observe!
Installation length spider,
Product Paper & Tech
Paper “Elastomer Jaw
Couplings“
Guided length/
Clamping length
Lubricate with
Vaseline (for easy
mounting).
Length expanding
mandrel
Assembly, Disassembly
Elastomer Jaw Couplings
RINGFEDER®GWE
Safety instructions
Rotating machine parts may injure operators and service staff!
Therefore:
Switch off the drive before assembly work.
Safeguard the machine against accidental switch-on.
Mount all covers and protection devices before switching on
the machine.
RINGFEDER®products may only be mounted by specialist staff
and for suitable applications.
Attention
Please read these instructions through carefully.
In the event of infringement of these notes all claims of
liability will become void.
RINGFEDER POWER TRANSMISSION reserves the right
to technical changes to improve the product.
RINGFEDER® Elastomer Jaw Couplings are accepted
state of the art.
If you experience problems or have any questions, our
technical and service staff will be happy to assist you. See
the reverse of these instructions for the corresponding
contact information.
Valid data on the required tightening torque can be
found in the Product Paper & Tech Paper “Elastomer
Jaw Couplings“ or on our website. Please check
whether the machinery manufacturer has provided
discrepant tightening torque values.
Designation CAS-Number (RoHS)
Vaseline 8009-03-8
Special grease RINGFEDER®FM15

03.2020 3
A3A2
A1
!
A5
A4
1
2
TA!
C1C1
GWE 5102
EN

03.2020 4
A7
H3
1
2!
A6
1
2
TA!
C1C1
GWE 5102
EN

03.2020 5
B3B2
B1
!
B5
B4
1
2
TA!C1C1
GWE 5103, GWE 5103.1, GWE 5104
EN

03.2020 6
B7
H3
1
2!
B6
1
2
TA!
C1C1
GWE 5103, GWE 5103.1, GWE 5104
EN

03.2020 7
C2
C1
!
C3
X
K1K1
C4
TA!
H3!
GWE 5106
EN

03.2020 8
D3D2
D1
!
D5D4
TA!L5
GWE 5107, GWE 5117
EN

03.2020 9
D7
H3
1
2
!
D6
1
2
TA!
C1
GWE 5107, GWE 5117
!
1
2
EN
The clamping screws must be tightened alternately in stages.
After five times assembly and disassembly, relubrication
of the screws at the thread and screw head with special grease
RINGFEDER®FM15 is necessary.

03.2020 10
E3
E2
E1
!
E5
E4 2
1
1.
2.
3.
TA!
C1C1
GWE 5112
EN

03.2020 11
E7
H3
1
2!
E6
1
2
1.
2.
3.
TA!
C1C1
GWE 5112
EN

03.2020 12
F3F2
F1
!
F4 1
TA!C1C1
GWE 5113
2
1
1
2
F5
!
EN
The clamping screws must be tightened alternately in stages.
After five times assembly and disassembly, relubrication
of the screws at the thread and screw head with special grease
RINGFEDER®FM15 is necessary.

03.2020 13
F7
H3
1
2
!
F6
1
TA!
GWE 5113
C1C1
2
1
2
!
EN
The clamping screws must be tightened alternately in stages.
After five times assembly and disassembly, relubrication
of the screws at the thread and screw head with special grease
RINGFEDER®FM15 is necessary.

03.2020 14
G1 C2G2
G4
C1C1
G3
1
2
H3
G5
TA!
1
2
H3
GWE Z5104.1
EN

03.2020 15
H1
H3
H2
X
K1K1
H4
TA!
H3
H3
GWE Z5106.1
EN

03.2020 16
GWE 5102
A3 A4
A5
A3
A1
1
2
A2
1
2
EN

03.2020 17
B4B3
B5
B1
1
2
B2
1
2
GWE 5103, GWE 5103.1, GWE 5104
EN

03.2020 18
C2C1
GWE 5106
EN

03.2020 19
GWE 5107, GWE 5117
D3 D4
D5
D1
1
2
D2
2
1
EN

03.2020 20
E4E3
E5
E1
1
2
E2
1
2
GWE 5112
EN