Rinnai Evolve RHFE950ETRN User manual

Evolve
Installation guide
Models: RHFE950ETRN/RHFE950ETRL
RHFE1250ETRN/RHFE1250ETRL

Appliance must be installed with a Rinnai approved flue
system.
This appliance shall be installed in accordance with:
- Manufacturer’s installation instructions
- AS/NZS 5601 Gas Installations
- Local regulations and municipal building codes
Installation, servicing and repair shall be carried out only
by authorised personnel.
Warning
Improper installation, adjustment, alteration, service or
maintenance can cause property damage, personal injury
or loss of life.
For more information about buying, using, and servicing
of Rinnai appliances call: 0800 RINNAI (0800 746 624).
Rinnai New Zealand Limited
105 Pavilion Drive, Mangere, Auckland
PO Box 53177, Auckland Airport, Auckland 2150
Phone: [phone]
Email: [email protected].nz
Web: www.rinnai.co.nz
www.youtube.com/rinnainz
www.facebook.com/rinnainz
Important:

cnt:
Before you start.................................................... 4
Specification......................................................... 5
Dimensions........................................................... 6
Gas supply ............................................................ 7
Electrical supply ................................................... 7
Wall penetration................................................... 8
Framing dimensions ............................................. 9
Clearances from combustibles............................. 10
TV installation....................................................... 12
Flueing options..................................................... 13
Evolve installation overview ................................. 14
Connect flue system............................................. 15
Install heater into enclosure................................. 16
Removing and replacing the glass panel.............. 17
Install burn media - log set................................... 18
Adding the granules............................................. 20
Install burn media - stones ................................... 21
Commissioning .................................................... 24
Install the inner and outer frame.......................... 25
Test operation and lighting sequence.................. 26
Installation checklist and customer handover ..... 26
Wiring diagram..................................................... 27

4 | Evolve Installation Guide: 12471-C 03-15
Before you start
Unpack the appliance and components and check for damage. DO NOT install any damaged items.
Check all components have been supplied and that you have the correct gas type.
Read these instructions to get an overview of the steps required before starting the installation. Failure
to follow these instructions could cause a malfunction of the appliance. This could result in serious injury
and/or property damage.
Flue installation guide
These instructions are to be used in conjunction with the Rinnai Arriva and Evolve flue installation guide
supplied with the flue kits.
Carton contents
The components for the Evolve are supplied in three separate cartons (four if a mesh guard is
purchased). Ensure all the components are supplied before starting the installation.
12
3
4
6
9
8
7
5
1. Evolve engine
2. Remote control and batteries
3. Remote control mounting bracket
4. Screw pack
5. Cable tie
6. Fascia mounting screws
7. Operation and installation guides
8. Granule packs 950 (x2), 1250 (x3)
9. Gas connections
• Inner frame
• Outer frame
Log set OR river stone set.
Images shown are for the 950 model,
The Evolve 1250 log set has an extra
two logs (10 in total), and the stone
set contains an extra 10 stones (40 in
total).
• Mesh guard (optional accessory),
packaged in a separate carton

Evolve Installation Guide: 12471-C 03-15 | 5
Specication
Evolve
Specification summary
Input = 10-34 MJ/h
Output = 2.4-8.13* kW
Efficiency = 86% (on high)
Heating area = 82-125 m2**
Gas type = NG or ULPG
Inbuilt exhaust balance flued
convection flame fire with electronic
temperature control, timer and
remote.
Suitability
Ideal for living rooms and open plan
areas. Versatile power flue system
makes for easy installation in almost
any living space, including bedrooms.
The Evolve is ideal for a new build
installation into a false (mock)
chimney.
Data plate
Located inside the appliance, upper
right hand side.
Convection fan
2-speed centrifugal, double diameter
160 x 180 mm.
Gas connection
½ “ BSP, the gas supply terminates
inside the heater—lower left hand
side of the appliance.
Ignition
Continuous spark electronic ignition.
Installation considerations
Room size—smaller rooms will heat
up quickly, and due to the efficiency
of the appliance, the heater (if auto
off is selected) will turn to a low flame
setting once the set temperature has
been reached.
Noise level - 37-45 dB(A)
Power flue
Inner 50 mm, outer 70~80 mm.
Appliance must be installed with a
Rinnai flue system.
Power consumption/electrical
supply
High = 90 W
Standby = <8 W
This heater has a 1.5 m power cord
with a three pin plug supplied. The
power cord passes through a slot in
the back right hand corner of the
appliance.
Safety devices
Flame failure sensing system,
pressure relief, overheat safety
switch, air temperature sensor,
thermal fuse, overcurrent fuse, and
spark detector.
Temperature control
Thermostatic, temperature control
range 16-26 °C.
Weights
• Evolve 950: 75 kg
• Evolve 1250: 100 kg
* Will vary according to gas type and flue configuration ** Will vary depending on geographical location in NZ

6 | Evolve Installation Guide: 12471-C 03-15
Dimensions
All dimensions are in mm.
960
1070 25 560 430 420
660
700
305
177
25 570
500 ± 25
65
Evolve 950
Evolve 1250
1255
1320 560 580 57025
620
1000
305162
570
10
500 ± 25
65

Evolve Installation Guide: 12471-C 03-15 | 7
Gas supply
Gas pipe sizing must consider the gas input to this appliance, as well as other gas
appliances in the premises. The gas supply termination is inside the heater, and enters
from the lower left hand side of the appliance.
To ensure correct positioning terminate the gas supply so it is 175 mm
in from the front face of the enclosure opening.
Purging the gas supply
Foreign materials and debris such as swarf, filings etc. must be purged
from the gas supply. Failure to do so may cause damage to the control
valve causing it to malfunction.
175 mm175 mm
Front of
enclosure
Consumer pipe
Adapter (supplied)
Rear of
enclosure
Gas supply pressure
to be 1.13 to 3 kPa
Flexible pipe (supplied)
175 mm*
197 mm**
* Where copper pipe ends
** With RNZ supplied adaptor
Electrical supply
This heater has a 1.5 m power cord with a three pin plug
supplied. The power cord passes through a slot in the
back right hand corner of the appliance.
Rinnai recommend the heater be plugged into a 230 V,
10 A earthed power point. The power point must not
be above the heater. Alternatively the appliance can
be direct wired if the power supply is to be concealed.
Consult a qualified electrician if direct wiring is required
as it must comply with AS/NZS 5601.1 and AS/NZS 3000
and other relevant local regulations.

8 | Evolve Installation Guide: 12471-C 03-15
Evolve 950
Wall penetration
Direct flue wall penetration requirements
Use the guide pictured to mark the penetration points for the gas supply and flue transition locations.
Consideration must be given to the position of any studs, noggins or other components of the wall
structure on both sides of the wall. Mark these measurements accurately as this is critical to a successful
installation.
The penetration for the flue transition only needs to be made for direct flue installations, where the
terminal is directly to the rear of the appliance. If no flue pipe penetration is required the markings are
still useful for indicating the correct position of the flue transition within the enclosure for other flue
applications.
For weatherboard walls, drill through the centre of the weatherboard from the outside, then drill from
the inside through the plaster board.
Ø 85~95
Gas supply penetration
Flue pipe penetration
500 ± 25
430 (right)
Centreline of enclosure
420 (left)
65
Base of enclosure
Dimensions are in mm.
Evolve 1250
Ø 85~95
Gas supply penetration
Flue pipe penetration
500 ± 25
580 (right)
Centreline of enclosure
570 (left)
65
Base of enclosure

Evolve Installation Guide: 12471-C 03-15 | 9
The main points governing location are flueing and warm air distribution. The Rinnai Evolve has an
integrated zero clearance box that isolates the appliance from combustible materials. This means it can
be installed directly into a decorative fireplace constructed from materials such as wood or plaster.
The heater must be positioned within the enclosure on a flat level surface that allows free movement of
the appliance. The joists used to support the appliance off the ground must be capable of supporting a
minimum of 1.5 times the weight of the appliance. Wheels located at the rear of the heater allows the
unit to slide in and out of the enclosure for installation and maintenance.
Please note
Depending on the type of flue being installed additional nogs may be required so the wall straps in each
flue kit can be securely attached. The additional bracing of the frame is normally completed by the
gasfitter.
D
W
H
Framing dimensions
Enclosure dimensions
950 1250
W-width 965-980 mm 1265-1280 mm
H-height 570-580 mm 570-580 mm
D-depth 570 mm min. 570 mm min.

10 | Evolve Installation Guide: 12471-C 03-15
Clearances from combustibles
The clearances listed below, measured from the edge of the glass, are
minimum clearances unless otherwise stated.
While the heater is operating
The appliance must not be
installed where curtains or
other combustible materials
could come into contact with
the heater.
The 1000 mm clearance
above is the clearance to the
ceiling.
Mantels and surrounds
Combustible mantels and
surrounds require clearance
from the fire to minimise
fire danger. Mantels
and surrounds, made of
combustible materials such as
wood, are allowed providing
they are outside the minimum
clearances shown.
Hearths
A hearth is not necessary but
can be used for decorative
purposes or protection of
sensitive flooring. A hearth
must not obscure the front of
the fire.
Floor protection
Heat emanating from this
fire may over time affect
the appearance of some
materials used for flooring,
such as, carpet, vinyl, cork or
timber. This may be amplified
if the air contains cooking
vapours or cigarette smoke.
To avoid this occurring, it is
recommended that a mat
be placed in front of this
appliance.
Note: Measurements are taken from the edge of the glass.
The 400 mm side clearance includes side walls.
400 400
1000
1000
400
A
B
C
AMantel needs to be a min. of 400 mm away from the edge of the glass.
B Max. mantel depth at 400 mm (A) is 250 mm max.
CSurround needs to be a minimum of 400 mm away from the edge of the
glass.
For every 50 mm of added mantel depth there must be an additional 100 mm
of clearance from the edge of the glass. For example:
Mantel depth
A
: clearance required
300 mm 500 mm
350 mm 600 mm
400 mm 700 mm

Evolve Installation Guide: 12471-C 03-15 | 11
The below diagrams are to assist people who are determining the clearance
area around the Evolve without having the unit on site.
Glass width
700400 400
460 400
Clearance Clearance
Minimum above fire
Minimum to ceiling
1500
1000
Evolve 950
Glass width
1000400 400
460 400
Clearance Clearance
Minimum above fire
Minimum to ceiling
1800
1000
Evolve 1250

12 | Evolve Installation Guide: 12471-C 03-15
TV installation
The Evolve has a fan that distributes warm air from the top of the appliance
out into the room. As warm air is dispersed outwards, as opposed to directly
upwards, installation of a TV may be an option.
The diagram shows
recommended clearances
when installing a TV directly
above the Evolve, or into a
recess. All dimensions are in
millimetres.
400 mm dimension
The 400 mm dimension
is the minimum clearance
required to to a mantel. The
image adjacent shows the
dimension from the edge
of the frame, in the case
of the Evolve the 400 mm
dimension can be taken from
the edge of the glass.
For a TV mounted directly
above the unit, the mantel
must be at least the depth of
the TV to deflect heat away.
Always check with the TV
manufacturer
It is up to the owner to check
the TV installation with the TV
manufacturer—some have
warranty conditions that state
a TV is not to be installed
above a fireplace.
Rinnai does not accept any
responsibility for damage to
a TV resulting from the use of
this information.
At least the
depth of the TV
400 mm
minimum
400 mm
minimum

Evolve Installation Guide: 12471-C 03-15 | 13
Flueing options
The below options detail the most common types of flue installations. If you have
an installation that varies from those below, please contact Rinnai. For further
detail on each of the options refer to the Arriva and Evolve flue installation guide.
Arriva flue components
- Direct A flue (R2731), or
- Direct B flue (R2732), or
- Direct flue (ASPDFK)
Evolve flue components
- Direct flue (ASPDFK)
* Adaption flue kit: Arriva use ASPKIT03, Evolve use EVOKIT03
Maximum flue length - 8.5 m Maximum number of bends - three One 90 bend = 1 m
For every 90 ° bend the overall length must be reduced by 1 m. For example, if an installation has three 90 ° bends,
the maximum flue length can be 5.5 m. The ASPKIT03/EVOKIT03 is counted as one 90 ° bend.
Direct and direct extended flueing
Direct through-the-wall flueing for walls up
to 385 mm thick. Flue can be extended if the
wall thickness is greater than 385 mm by using
the ASPDFK flue kit and additional lengths of
ESPIPE900.
In-wall vertical flueing
The vertical in-wall flue installation is installed
against an internal wall within a false fireplace
or other suitable cavity, and is run vertically
upwards to a termination point.
Vertical in-wall direct (A)
- Adaption flue kit*
- Flue pipe (ESPIPE900)
- Roof cowl (ESROOFCOWL)
Vertical in-wall offset (B)
- Adaption flue kit*
- Flue pipe (ESPIPE900)
- 45 ° bends (ESBEND)
- Roof cowl (ESROOFCOWL)
Sideways flueing
The sideways flue installation can run along
the left or right hand side of the internal wall
behind the heater. When considering the
location of the fire ensure the flue path is free
from obstructions such as studs, noggins,
wiring, joists etc.
- Adaption flue kit*
- Flue pipe (ESPIPE900)
- Wall terminal (ESWTERM)
Down-and-out flueing
The down-and-out flue option allows for the
adpation flue kit to face downwards and for
the flue to run vertically through a hole in the
floor, and then terminate horizontally outside
(must be 300 mm above ground).
- Adaption flue kit*
- Flue pipe (ESPIPE900)
- Wall plate (ESPLATE)
- 45 ° bends (ESBEND)
- Wall terminal (ESWTERM)
Through-wall vertical flueing
For the small number of instances where the
appliance cannot be directly flued or flued via
an internal wall. In some cases a large portion
of the flue may be visible from the outside.
- Direct flue (ASPDFK)
- 45 ° bends (ESBEND)
- Flue pipe (ESPIPE900)
- Condensate trap (ESCONDK)
- Roof cowl (ESROOFCOWL)

14 | Evolve Installation Guide: 12471-C 03-15
Evolve installation overview
1. Construct frame as per
enclosure dimensions on p. 9.
2. Line wall—could also plaster at
this stage.
3. Complete the gas connection
refer p. 7. Electrical supply
can also be completed at this
point.
4. Connect flue system. 5. Install heater into enclosure*,
screw to frame, and complete
gas, air hose, and flue
connection p. 16.
6. Install burn media, refer p
18-23.
8. Install outer frame, mesh
guard (if purchased), and
inner frame refer p. 25.
11. Complete installation
checklist in operation guide
and complete customer
handover—add a touch of
magic!
7. Commission unit, refer p. 24. 9. Test operation and lighting
sequence, refer p. 26.
* Two hand-holds, either side of the unit, have been added to help move and lift
the fire into place. N.B: Earlier models of the Evolve 950 do not have these.

Evolve Installation Guide: 12471-C 03-15 | 15
Connect ue system
Consult the Rinnai Arriva and Evolve flue installation guide supplied with the Arriva/
Evolve flue kits for detailed flue installation instructions. For connection of the flue to the
heater refer information below.
Removing the pipe clamp, extension tube and exhaust pipe
Before installing the heater into the enclosure the pipe clamp, telescopic extension tube, and exhaust
pipe need to be removed so there is room to connect the flue system.
1. Undo the pipe clamp and remove the telescopic extension tube from the exhaust pipe.
2. Secure the telescopic extension tube to the flue system with the exhaust pipe lock.
3. Attach the air hose to the flue transition and secure with the cable tie provided.
Please note that in the adjacent image in step 4 the air hose is already connected to the flue. It is much
easier to connect the air hose to the unit than to connect the air hose to the flue once the heater
is in place. Ensure the air intake hose of the heater is properly secured to the air connection on the
flue system using the cable tie provided, and that the rubber seal is placed on the unused air intake
connection.
Flue slide stopper
Flue transition (ASPDFK, EVOKIT03)
The flue transition provides a connection between the flue system and the heater’s flue spigot and air
intake. For all flueing installations, except horizontal direct flueing, the flue transition is counted as a
90 ° bend. The flue transition requires a 5 mm clearance from combustibles. This clearance is provided
automatically when the supplied standoff brackets are used. All other flue components, except the
elbow section of the EVOKIT03, are designed for zero clearance and can be placed hard against timber
or plasterboard.
The exhaust pipe lock is provided with the ASPDFK and EVOKIT03 flue kits
Flue transition outlet
Unused air intake
Air intake
Wall terminal
ASPDFK
ASPKIT03/EVOKIT03
Elbow component is
counted as a 90° bend

16 | Evolve Installation Guide: 12471-C 03-15
Install heater into enclosure
1. Carefully move the heater into the enclosure, guiding the piping, flexible gas connection, and
telescopic extension tube into the access openings and through the appliance. Ensure that the air
hose is not in a position where it could get caught or crushed by the unit.
2. Once the engine is in place reconnect the flue exhaust to the telescopic extension tube and secure
together with the pipe clamp.
3. Secure the heater flange in place using 11 screws (seismic constraint).
4. Complete gas, air hose, and flue connection. If vertically flueing ensure condensate tube, provided
with the EVOKIT03 flue kit, is attached to the condensate pipe on the heater—refer images below.
Please note: The unit is supplied with the heater condensate already connected.
Flue locking clamp
Telescopic extension tube
Flue exhaust
Flange screw position—11 in total Flue condensate pipe connection
The engine comes with the heater condensate already connected.

Evolve Installation Guide: 12471-C 03-15 | 17
Removing and replacing the glass panel
Before the burn media can be installed into the combustion chamber, the glass panel needs to be
removed. Remove the four retaining screws—two at the top and two at the bottom. When replacing
tighten all four screws and then back off by quarter of a turn. If the glass panel is screwed too tight, the
panel will bow and the spring release mechanism won’t work properly.
The glass panel needs to be replaced after installing the burn media and before commissioning.
Front panel of the Evolve showing the four screw positions for removing and re-
placing the glass panel

18 | Evolve Installation Guide: 12471-C 03-15
Install burn media - log set
It is important to place the pieces in the correct position. Incorrect placement can create
carbon build-up and affect performance. Malfunctioning due to improper log/granule
placement is not covered by warranty. The unit must never be used with broken logs or other
burn media (except those specifically designed for the Evolve).
2
34
5
67
8
1
The glass retainer will need to be removed before installing the log set and
granules. Use extreme care when handling the log pieces, they are made from a
fragile material and will damage easily.
Use these instructions in conjunction with the burn media guide sheet,
which is attached to the engine. Experience has shown that the majority of
performance problems has been caused by the burn media being installed
incorrectly.
IMPORTANT
Evolve 950 Evolve 1250
Evolve 950 burner bed
Evolve 1250 burner bed
- locating pin - locating bracket
12
345
678
910

Evolve Installation Guide: 12471-C 03-15 | 19
7. Front large middle log
Place onto the locating pin of log four and slot onto the
right front locating bracket.
8. Top upper right large log
Place onto the locating pin of log seven and swivel OVER
log 4. For the 950 the end rests into the burner slot. For
the 1250 the end will rest in FRONT of the locator tab.
5. Front middle small log
Refer fully assembled image for reference. Place onto the
middle locating pin and central front locator bracket.
6. Front large left log
Place onto the locating pin of the first log and slot onto
the left front locating bracket.
56
78
3. Front left small log
Refer fully assembled image for reference. Place onto the
middle left locating pin and left front locator bracket.
4. Front right small log
Refer fully assembled image for reference. Place onto the
middle right locating pin and right front locator bracket.
34
1. Back left log
Align bottom locating holes with the locating pins at the
back of the burner—the log will sit up against the back of
the combustion chamber.
2. Back right log
Align bottom locating holes with the locating pins at
the back of the burner—the log will sit up against the
back of the combustion chamber, and there will be a gap
between the back two logs.
12
The installation procedure for both models is the same. The only difference is the position of log
eight and the addition of logs 9 and 10—the Evolve 1250 has an extra two logs.

20 | Evolve Installation Guide: 12471-C 03-15
9. Far LHS small log (1250 model only)
Fit the far small left hand log onto the two locator
brackets.
10. Far RHS small log (1250 model only)
Fit the far small right hand log onto the two locator
brackets.
• Evolve 950: Two granule packs
• Evolve 1250: Three granule packs
Adding the granules
The granules as well as being added to create a more realistic log flame affect (by diffusing the gas flames
through the burner ports) also assist in soot prevention and are CRITICAL to the performance of the
heater. Never pour the granules directly from the pack as dust particles from the plastic bag may block
the ports.
DO NOT place the granules near the flame rods or the pilot (areas highlighted in the images below) as
this will cause a blockage and the unit will not start.
Place the granules evenly (do not stack) around the logs in the front part of the burner and on the
middle section of the burner (in the gaps between the logs)—refer fully assembled image.
Adding the granules
Evolve 950 Evolve 1250
910