RIOTEC DC9257AN User manual

1
Quick Guide
-DC9257AP (with Battery)
-DC9257AN (without Battery)
1 H92P/H92N
Connect to micro USB port of OTG device
2 H92P/H92N
3

* Before you use it, please switch to "C" for battery charge for
3~4 hours.
*Under “C mode”, you can raise/lower soft-keyboard easily.
4

H92P Scan Holder is with Li-Ion battery inside. When in
charging, please use the original power adaptor of
smartphone (recommend). Through it, it charges both OTG
device and H92P internal battery at the same time. When in
low battery (Red LED flashing), please charge it
immediately.
LED Indicator Information
Green LED OFF Full charged (Charge mode)
Green LED ON Charging (Charge mode)
Red LED Flashing Low battery (Operation mode)
Attention: Under “Operation mode” please do not charging,
otherwise the OTG device's battery will be charging back to
H92P’s battery.
5


The touch trigger is in the central area of mini scanner. (for both side).
Please check the above drawing for your reference.
Installation
Before using scanner, please make sure that the OTG device is fully charged.
1. Under USB HID interface
** When plugged into OTG device, it will be recognized and begin to scan
the barcode.
2. Under USB Serial interface
** Please install PL-2303 driver into your OTG device first. PL-2303 driver
can be downloaded from Google Play
** Connect scanner to your OTG device, then, you can know which serial
port scanner connects to.
** The data you scan will be sent to serial port and your APP can get the
data from serial port directly.
Trigger
Area
Suction Cup
PU Glue
(Can be used
repeatedly)
Micro USB
cable (OTG)
Mini
scanner
Micro USB
H92P with
Li- Ion Battery/
H92N without
Battery
Micro USB
LED Indicator
H92P only
O = Operation mode C = Char
g
e mode
LED Indicator
H92P only

2
Reset Configuration to Defaults
If you are unsure of the scanner configuration or have scanned the
incorrect codes, please from A1 to A7 for USB HID or B1 to B7 for USB
Serial. This will reset the scanner to its factory defaults.
USB HID USB Serial
A1 B1
A2 B2
A3 B3
A4 B4
A5 B5
A6 B6
A7 B7
Note: Please install PL-2303 driver for USB Serial.
Barcode Configuration Method:
(Flow chart for setup procedure :)
Start
Configuration
End
Configuration
Keyboard Language(For USB HID only)
Scan the appropriate country code as below to program the keyboard
layout for your country or language. As a general rule, the following
characters are supported, but need special care for countries other
than the United States: @ | $ # { } [ ] = / ‘ \ < > ~
USA
(Original setting)
Japan
Denmark Finland
France Germany
Italy Norway
1D Symbologies – 1
ENABLE
CODE 39 DISABLE
ENABLE
CODE 39
FULL ASCII
DISABLE
ENABLE
CODE 39 Transmit
Start/Stop Character DISABLE
ENABLE
UPC-E DISABLE
ENABLE
UPC-A DISABLE
ENABLE
Interleaved
25 DISABLE
ENABLE
Matrix
25 DISABLE
ENABLE
Industrial 25 DISABLE
ENABLE
CODE 93 DISABLE

3
Barcode Configuration Method:
(Flow chart for setup procedure :)
Start
Configuration
End
Configuration
1D Symbologies – 2
ENABLE CODABAR DISABLE
ENABLE CODE 128 DISABLE
ENABLE
GS1-128
UCC/EAN-128
DISABLE
ENABLE MSI DISABLE
1D Symbologies – 3
ENABLE CODE 11 DISABLE
ENABLE
GS1-Databar
(RSS) DISABLE
ENABLE
GS1-Databar
(RSS-Limited) DISABLE
ENABLE
GS1-Databar
(RSS-Expand) DISABLE
ENABLE ISSN DISABLE
ENABLE ISBN DISABLE
ENABLE EAN-8 DISABLE
ENABLE EAN-13 DISABLE
Inter-Keystroke Delay (FOR USB HID Only)
This parameter specifies the delay between emulated keystrokes
No Delay Short Delay
(5ms)
Medium Delay
(10ms)
Long Delay
(15ms)
 Information in this document is subject to change without notice.
Q_200325_01