Risco RWT6F User manual

1
WIRELESS FL OOD DETECTOR
Model: RWT6F
Installation instructions
1 General Description
The wireless flood detector is a fully supervised detector used to
detect the presence of water based liquids at any desired location
such as basements or water tanks.
The detector is comprised from 2 parts: Wireless transmitter and
flood sensor which are connected by 2.4m cable.
The detector operates with RISCO Group's programmable wireless
receivers.
2 Activating the Battery
Remove the red battery isolation strip to activate the battery.
3 LED Indication
On: The LED turns on each time the detector transmits (alarm,
tamper or supervision). Blink: Low battery condition. The LED will
blink on each transmission.
4 Quick Device Allocation at the WiComm
Smart Hub
When adding a flood detector device using the device wizard setup,
enter the flood detector Serial Number in the wizard. If you later
purchase an extra detector you can enroll it as follows:
To quickly allocate the sensor at the WiComm Smart Hub:
If the WiComm Smart Hub is not already in Learn mode, press the
button on the WiComm Smart Hub for 5 seconds; the unit
beeps once as it enters Learn mode (all the LEDs also light up, one
after the other).
Remove the red isolation strip from the battery and make sure the
cover is removed so the internal tamper switch is accessible.
Send a signal transmission from the flood detector by pressing the
tamper button for at least 2 seconds; the WiComm Smart Hub beeps
once to accept or beeps three times to reject. Once accepted, the
system announces the device type and its zone (for example,
“Detector, zone 1”).
When the detectors have been enrolled, short-press the WiComm
Smart Hub button to exit Learn mode; the unit beeps once and
the LEDs stop flashing.
After quick device allocation you may change the zone label on the
user web at www.riscocloud.com.
Note: For future use, it is recommended to write down the detector
description, zone number, and installation location of each allocated
detector.
5 Installation
Select a mounting location that is suitable both for the transmitter
and the flood sensor as follows:
Transmitter Mounting Location:
• Place the transmitter at the highest possible position to improve
communication and prevent from coming wet in the event of
flooding.
• Test the transmitter's communication quality by generating an
alarm and verifying that the receiver has received it. If the alarm
signal is not detected, reposition the transmitter and try again.
Flood Sensor Mounting location:
The flood sensor should be placed in a position where water will
accumulate rapidly in an event of flooding.
After selecting the mounting location:
1. Attach the flood sensor in horizontal position near the floor with
using the double-sided adhesive.
2. Secure the flood sensor cable to the wall.
Note: It is recommended to place the flood sensor cable inside metal
or plastic pipe.
6 Battery Replacement
For battery replacement, follow the procedure in the illustration
below.
©
Red battery
isolation strip

2
6 Jumpers Settings
Please do not change the jumper settings.
8 Technical Specifications
Electrical
Current consumption
(standby)
10 uA standby
Battery life 5 years
Range (LOS) 130m (426 feet)
Voltage requirements CR123A 3VDC Lithium Batteries
Frequency 915MHz
Physical
Size
(LxWxD)
81 x 35 x 32 mm
(3.2 x 1.37 x 1.27 in.)
Environmental
Operating temperature 0°C to 55°C (-32°F to 131°F)
Storage temperature -20°C to 60°C (-4°F to 140°F)
Standard Limited Product Warranty (“Limited Warranty”)
RISCO Ltd. (“RISCO") guarantee RISCO’s hardware products (“Products”) to be
free from defects in materials and workmanship when used and stored under
normal conditions and in accordance with the instructions for use supplied by
RISCO, for a period of (i) 24 months from the date of delivery of the Product (
the “Warranty Period”). This Limited Warranty covers the Product only within the
country where the Product was originally purchased and only covers Products
purchased as new.
Contact with customers only. This Limited Warranty is solely for the benefit of
customers who purchased the Products directly from RISCO or from an
authorized distributor of RISCO. RISCO does not warrant the Product to
consumers and nothing in this Warranty obligates RISCO to accept Product
returns directly from end users who purchased the Products for their own use
from RISCO’s customer or from any installer of RISCO, or otherwise provide
warranty or other services to any such end user directly. RISCO’s authorized
distributor or installer shall handle all interactions with its end users in connection
with this Limited Warranty. RISCO’s authorized distributor or installer shall make
no warranties, representations, guarantees or statements to its end users or
other third parties that suggest that RISCO has any warranty or service
obligation to, or any contractual privy with, any recipient of a Product.
Remedies. In the event that a material defect in a Product is discovered and
reported to RISCO during the Warranty Period, RISCO shall accept return of the
defective Product in accordance with the below RMA procedure and, at its
option, either (i) repair or have repaired the defective Product, or (ii) provide a
replacement product to the customer.
Return Material Authorization. In the event that you need to return your Product
for repair or replacement, RISCO will provide you with a Return Merchandise
Authorization Number (RMA#) as well as return instructions. Do not return your
Product without prior approval from RISCO. Any Product returned without a
valid, unique RMA# will be refused and returned to the sender at the sender’s
expense. The returned Product must be accompanied with a detailed description
of the defect discovered (“Defect Description”) and must otherwise follow
RISCO’s then-current RMA procedure published in RISCO’s website at
www.riscogroup.com in connection with any such return. If RISCO determines in
its reasonable discretion that any Product returned by customer conforms to the
applicable warranty (“Non-Defective Product”), RISCO will notify the customer of
such determination and will return the applicable Product to customer at
customer’s expense. In addition, RISCO may propose and assess customer a
charge for testing and examination of Non-Defective Product.
Entire Liability. The repair or replacement of Products in accordance with this
Limited Warranty shall be RISCO’s entire liability and customer’s sole and
exclusive remedy in case a material defect in a Product is discovered and
reported as required herein. RISCO’s obligation and this Limited Warranty are
contingent upon the full payment by customer for such Product and upon a
proven weekly testing and examination of the Product functionality
Limitations. This Limited Warranty is the only warranty made by RISCO with
respect to the Products. The warranty is not transferable to any third party. To
the maximum extent permitted by applicable law, this Limited Warranty shall not
apply and will be void if: (i) the conditions set forth above are not met (including,
but not limited to, full payment by customer for the Product and a proven weekly
testing and examination of the Product functionality); (ii) if the Products or any
part or component thereof: (a) have been subjected to improper operation or
installation; (b) have been subject to neglect, abuse, willful damage, abnormal
working conditions, failure to follow RISCO’s instructions (whether oral or in
writing); (c) have been misused, altered, modified or repaired without RISCO’s
written approval or combined with, or installed on products, or equipment of the
customer or of any third party; (d) have been damaged by any factor beyond
RISCO’s reasonable control such as, but not limited to, power failure, electric
power surges, or unsuitable third party components and the interaction of
software therewith or (e) any failure or delay in the performance of the Product
attributable to any means of communication provided by any third party service
provider, including, but not limited to, GSM interruptions, lack of or internet
outage and/or telephony failure. BATTERIES ARE EXPLICITLY EXCLUDED
FROM THE WARRANTY AND RISCO SHALL NOT BE HELD RESPONSIBLE
OR LIABLE IN RELATION THERETO, AND THE ONLY WARRANTY
APPLICABLE THERETO, IF ANY, IS THE BATTERY MANUFACTURER'S
WARRANTY. RISCO does not install or integrate the Product in the end user’s
security system and is therefore not responsible for and cannot guarantee the
performance of the end user’s security system which uses the Product or which
the Product is a component of.
This Limited Warranty applies only to Products manufactured by or for RISCO.
Further, this Limited Warranty does not apply to any software (including
operating system) added to or provided with the Products or any third-party
software, even if packaged or sold with the RISCO Product. Manufacturers,
suppliers, or third parties other than RISCO may provide their own warranties,
but RISCO, to the extent permitted by law and except as otherwise specifically
set forth herein, provides its Products “AS IS”. Software and applications
distributed or made available by RISCO in conjunction with the Product (with or
without the RISCO brand), including, but not limited to system software, as well
as P2P services or any other service made available by RISCO in relation to the
Product, are not covered under this Limited Warranty. Refer to the Terms of
Service at: https://riscocloud.com/ELAS/WebUI/UserLogin/License for details of
your rights and obligations with respect to the use of such applications, software
or any service. RISCO does not represent that the Product may not be
compromised or circumvented; that the Product will prevent any personal injury
or property loss by burglary, robbery, fire or otherwise, or that the Product will in
all cases provide adequate warning or protection. A properly installed and
maintained alarm may only reduce the risk of a burglary, robbery or fire without
warning, but it is not insurance or a guarantee that such will not occur or will not
cause or lead to personal injury or property loss. CONSEQUENTLY, RISCO
SHALL HAVE NO LIABILITY FOR ANY PERSONAL INJURY, PROPERTY
DAMAGE OR OTHER LOSS BASED ON ANY CLAIM AT ALL INCLUDING A
CLAIM THAT THE PRODUCT FAILED TO GIVE WARNING.
EXCEPT FOR THE WARRANTIES SET FORTH HEREIN, RISCO AND ITS
LICENSORS HEREBY DISCLAIM ALL EXPRESS, IMPLIED OR STATUTORY,
REPRESENTATIONS, WARRANTIES, GUARANTEES, AND CONDITIONS
WITH REGARD TO THE PRODUCTS, INCLUDING BUT NOT LIMITED TO
ANY REPRESENTATIONS, WARRANTIES, GUARANTEES, AND
CONDITIONS OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE, TITLE AND WARRANTIES AGAINST HIDDEN OR LATENT
DEFECTS, TO THE EXTENT PERMITTED BY LAW. WITHOUT LIMITING THE
GENERALITY OF THE FOREGOING, RISCO AND ITS LICENSORS DO NOT
REPRESENT OR WARRANT THAT: (I) THE OPERATION OR USE OF THE
PRODUCT WILL BE TIMELY, SECURE, UNINTERRUPTED OR ERROR-
FREE; (ii) THAT ANY FILES, CONTENT OR INFORMATION OF ANY KIND
THAT MAY BE ACCESSED THROUGH THE PRODUCT SHALL REMAIN
SECURED OR NON DAMAGED. CUSTOMER ACKNOWLEDGES THAT
NEITHER RISCO NOR ITS LICENSORS CONTROL THE TRANSFER OF
DATA OVER COMMUNICATIONS FACILITIES, INCLUDING THE INTERNET,
GSM OR OTHER MEANS OF COMMUNICATIONS AND THAT RISCO’S
PRODUCTS, MAY BE SUBJECT TO LIMITATIONS, DELAYS, AND OTHER
PROBLEMS INHERENT IN THE USE OF SUCH MEANS OF
COMMUNICATIONS. RISCO IS NOT RESPONSIBLE FOR ANY DELAYS,
DELIVERY FAILURES, OR OTHER DAMAGE RESULTING FROM SUCH
PROBLEMS. RISCO WARRANTS THAT ITS PRODUCTS DO NOT, TO THE
BEST OF ITS KNOWLEDGE, INFRINGE UPON ANY PATENT, COPYRIGHT,
TRADEMARK, TRADE SECRET OR OTHER INTELLECTUAL PROPERTY
RIGHT IN ANY EVENT RISCO SHALL NOT BE LIABLE FOR ANY AMOUNTS
REPRESENTING LOST REVENUES OR PROFITS, PUNITIVE DAMAGES, OR
FOR ANY OTHER INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL
DAMAGES, EVEN IF THEY WERE FORESEEABLE OR RISCO HAS BEEN
INFORMED OF THEIR POTENTIAL
FCC ID: JE4RWT6F915
IC: 6564A-RWT6F
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that
may cause undesired operation
Changes or modifications to this equipment which are not expressly approved by
the party responsible for compliance (RISCO Group's.) could void the user's
authority to operate the equipment.
FCC Note
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment on and off, the user is encouraged to try to correct the
interference by one or more of the following measures:
 Reorient or relocate the receiving antenna.
 Increase the separation between the equipment and the receiver.
 Connect the equipment into an outlet on to a different circuit from that to
which the receiver is connected.
 Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications to this equipment which are not expressly approved by
the party responsible for compliance (RISCO Group's.) could void the user's
authority to operate the equipment.
IC Warning
This device complies with Industry Canada licence-exempt RSS
standard(s). Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference, including interference that
may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables
aux appareils radio exempts de licence. L'exploitation est autorisée aux
deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage,
et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d'en compromettre le
fonctionnement
© RISCO Group 06/18 5IN2583 B