RiverRidge Madison 06-110 User manual

ASSEMBLY INSTRUCTIONS
RiverRidge® Madison Two-Door Floor Cabinet
ITEM#: 06-110 White
ITEM#: 06-121 Gray
ADULT ASSEMBLY REQUIRED
This product requires assembly by an adult because of small parts. Care should be taken
in unpacking and assembling this item to keep small parts away from children. During assembly
children should be kept away from the product due to possible risk of injury.
WARNING SEE FULL WARNING ON PAGE 2
Young children can be seriously injured or killed if furniture tips over. Don’t use
this item for a TV stand or place heavy objects on top of item. Always use
angle-braces or anchors to secure furniture to the wall.

THIS SHELF UNIT WILL HOLD UP TO 20 POUNDS PER SHELF OR TOP BOARD FOR A
TOTAL OF 60 POUNDS. DO NOT LOAD EACH SHELF WITH MORE THAN 20 POUNDS OR 60
POUNDS TOTAL WEIGHT. IF OVERLOADED WITH MORE THAN 20 POUNDS PER SHELF
OR 60 POUNDS TOTAL WEIGHT, SHELF MAY TIP FROM THE WALL AND CAUSE SERIOUS
INJURY OR DEATH.

PARTS LIST
NO
QTY
DESCRIPTION
1
1PC
Top Board
2
1PC
Bottom Board
3
1PC
Left Side Panel
4
1PC
Right Side Panel
5
1PC
Cross Bar
6
1PC
Adjustable Shelf
7
1PC
Left Door
8
1PC
Right Door
9
1PC
Upper Back Panel
10
1PC
Lower Back Panel

PARTS LIST
NO
PARTS
QTY
DESCRIPTION
A
8PCS
Cam Bolt
B
8PCS
Cam Lock
C
8PCS
Wood Dowel
D
4PCS
Shelf Holder
E
4PCS
Hinge
F
2PCS
Handle
G
24PCS
Screw (4x12mm)
H
1PC
Plastic Connection Strip
I
2PCS
Screw (4x14mm)
J
2PCS
Adjustable Anchor Bracket
K
16PCS
Screw (2.5x10mm)
L
2PCS
Plastic Anchor
M
2PCS
Screw (4x30mm)
N
4PCS
Screw (3.5x12mm)
TOOLS NEEDED FOR ASSEMBLY: FLAT & PHILLIPS SCREWDRIVER (NOT INCLUDED)
THE USE OF A POWER SCREWDRIVER IS NOT RECOMMENDED FOR ASSEMBLY
DO NOT USE ITEM IF ANY PARTS ARE MISSING OR DAMAGED
To order replacement parts at no cost to you, email [email protected], call
1-(844)-223-5201 or order parts online at www.riverridgehome.com. Only valid in the United States.
If purchased outside of the United States, please contact retailer where purchased.

STEP 1
1. Screw 4 cam bolts (A) into cam bolt holes on top board (1).
2. Attach 2 brackets (J) to top board (1) by inserting 2 screws (I) through holes on bracket (J)
and tighten to top board (1).
STEP 2
1. Screw 2 cam bolts (A) into cam bolt holes on left side panel (3).
2. Screw 2 cam bolts (A) into cam bolt holes on right side panel (4).
STEP 3
1. Insert 4 wood dowels (C) into wood dowel holes on left side panel (3).
2. Attach left side panel (3) to cross bar (5) and bottom board (2) by inserting wood dowels
into wood dowel holes on cross bar (5) and inserting cam bolts and wood dowels into cam lock
holes and wood dowel holes on bottom board (2).
3. Insert 2 cam locks (B) into cam lock holes on bottom board (2) and rotate clockwise to
secure cam bolts in place.
4. Repeat above steps to assemble right side panel (4) to cross bar (5) and bottom board (2).

STEP 4
1. Attach top board (1) to left side panel (3) and right side panel (4) by inserting cam bolts into
cam lock holes on left side panel (3) and right side panel (4).
2. Insert 4 cam locks (B) into cam lock holes on left side panel (3) and right side panel (4),
then rotate clockwise to secure cam bolts in place.
STEP 5
1. Attach upper back board (9) and lower back board (10) together by sliding into plastic
connection strip (H).
2. Attach upper back board (9) and lower back board (10) to cabinet by inserting 16 wood
screws (K) through holes on upper back board (9) and lower back board (10) then tighten
to cabinet.

STEP 6
1. Attach 2 hinges (E) to left door (7) by inserting 4 screws (G) through holes on hinges (E),
then tighten to left door (7).
2. Attach handle (F) to left door (7) by inserting 2 screws (N) through holes on handle (F),
then tighten to left door (7).
3. Repeat above steps to assemble hinges (E) and handle (F) to right door (8).
STEP 7
1. Attach left door (7) to cabinet by inserting 8 screws (G) through holes on hinges (E) then
tighten to left side panel (3).
2. Attach right door (8) to cabinet by inserting 8 screws (G) through holes on hinges (E) then
tighten to right side panel (4).
*Note: Tightening screw in position “a” will adjust doors up or down; tightening screw in position “b” will
adjust doors to or from cabinet and tightening screw in position “c” will adjust doors side to side.
Door Adjustments

STEP 8
Option #1: Securing to Drywall
1. Position cabinet against wall in desired location. Using a pencil, make two small marks on wall
through holes on brackets (J). Move cabinet away from wall and screw 2 plastic anchors (L)
into wall on pencil marks.
2. Place cabinet against wall, insert 2 screws (M) through holes on brackets (J), then tighten
to plastic anchors (L).
Option #2: Securing to Drywall and Wood Stud
1. Position cabinet against wall in desired location. Insert 2 screws (M) through holes on brackets
(J), then tighten through drywall and into wood stud.
*Tip: Anchor bracket (J) can be adjusted to correct distance from wall to cabinet as needed. Once adjusted,
be sure to re-tighten bracket inside cabinet for stability.
STEP 9
1. Insert 4 shelf holders (D) into holes at desired shelf height position.
2. Place shelf (6) on 4 shelf holders (D).

ATTENTION ADULTS: Cabinet should be checked periodically for damage or
loose screws/parts. Take appropriate action necessary to correct hazards such as
tightening of screws and taking any damaged parts away from children.
WARNING Please make sure your item is
secured to the wall, per assembly instructions.
CARE INSTRUCTIONS:
Wipe clean with a water dampened cloth. Wipe dry with clean cloth.
IMPORTANT:
Keep assembly instructions for future reference

Enjoy your new RiverRidge® Cabinet!
Thank you for purchasing this RiverRidge® Home item. We hope you
enjoy it and consider purchasing other RiverRidge® items.
To order replacement parts at no cost to you, email [email protected], call
1-(844)-223-5201 or order parts online at www.riverridgehome.com. Only valid in the United States.
If purchased outside of the United States, please contact retailer where purchased.
RiverRidge® is a registered trademark of Sourcing Solutions, Inc., Hudson, WI 54016