RiverRidge Woodbury 16-026 User manual

ASSEMBLY INSTRUCTIONS
RiverRidge®Woodbury Storage Bench
with Cubbies
ITEM #: 16-026
ADULT ASSEMBLY REQUIRED
This product requires assembly by an adult because of small parts. Care should be taken in
unpacking and assembling this item to keep small parts away from children.
WARNING SEE FULL WARNING ON PAGE 2
Young children can be seriously injured or killed if furniture tips over. Don’t use
this item for a TV stand or place heavy objects on top of item.Always use
angle-braces or anchors to secure furniture to the wall.

THIS SHELF UNIT WILL HOLD UP TO 20 POUNDS PER SHELF FOR TOTAL OF 60
POUNDS AND BENCH SEATING WEIGHT CAPACITY IS 200 POUNDS. DO NOT LOAD
SHELVES WITH MORE THAN 20 POUNDS OR SEATING WITH MORE THAN 200
POUNDS. OVERLOADING WITH MORE THAN 20 POUNDS PER SHELF OR 200 POUNDS
SEATING MAY CAUSE DAMAGED TO THE SHELF OR SERIOUS INJURY OR DEATH.

PARTS LIST
NO
QTY
DESCRIPTION
1
1PC
Top Board
2
1PC Left Rail Board
3
1PC
Right Rail Board
4
1PC
Back Rear Board
5
1PC
Bottom Board
6
1PC
Left Side Panel
7
1PC
Right Side Panel
8
2PCS
Divider Board
9
1PC
Back Board
10
1PC
Cushion
11
4PCS
Metal Leg
12
1PC
Middle Support Leg

PARTS LIST
NO PART QTY DESCRIPTION
A
6PCS Cam Bolt
B
6PCS Cam Lock
C
22PCS Wood Dowel (8x30mm)
D
5PCS
Screw(4x35mm)
E
4PCS Screw (4X35mm)
F
8PCS Machine Screw (6x30mm)
G
2PCS Machine Screw (6X10mm)
H
8PCS Shim
TOOLS NEEDED FOR ASSEMBLY: FLAT & PHILLIPS SCREWDRIVER (NOT INCLUDED)
THE USE OF POWER SCREWDRIVER IS NOT RECOMMENDED FOR ASSEMBLY
TOOL NEEDED FOR SECURING TO WALL: POWER DRILL (NOT INCLUDED)
To order replacement parts at no cost to you, email [e-mail],
call 1-(844)-223-5201 or order parts online at www.riverridgehome.com

STEP 1
1. Screw 2 cam bolts (A) into pre-threaded holes on left rail board (2) and right rail board (3).
2. Screw 4 cam bolts (A) into pre-threaded holes on top board (1).
STEP 2
1. Insert 1 wood dowel (C) into wood dowel hole on left rail board (2).
2. Attach left rail board (2) to rear rail board (4) by inserting wood dowel (C) into wood dowel hole and
insert cam bolt (A) into cam lock hole on rear rail board (4).
3. Insert 1 cam lock (B) into cam lock hole on rear rail board (4), then rotate clockwise to secure cam bolt
in place.
4. Repeat above steps to assemble right rail board (3) to rear rail board (4).

STEP 3
1. Insert 4 wood dowels (C) into wood dowel holes on left rail board (2), right rail board (3) and rear rail
board (4).
2. Attach top board (1) to left rail board (2), right rail board (3) and rear rail board (4) by inserting wood
dowels (C) into wood dowel holes on top board (1).
3. Insert 5 screws (D) through holes on top board (1), then tighten to left rail board (2), right rail board (3)
and rear rail board (4).
STEP 4
1. Insert 8 wood dowels (C) into wood dowel holes on top board (1)
2. Attach left side panel (6) and right side panel (7) to top board (1) by inserting wood dowels (C) into
wood dowel holes and inserting cam bolts (A) into cam lock holes on left side panel (6) and right side
panel (7).
3. Insert 4 cam lock (B) into cam lock holes on left side panel (6) and right side panel (7), then rotate
clockwise to secure cam bolts in place.
4. Attach 2 divider boards (8) to top board (1) by inserting wood dowels (C) into wood dowel holes on 2
divider boards (8).

STEP 5
1. Slide back board (9) into grooves on left side panel (6), right side panel (7) and top board (1).
2. Insert 8 wood dowels (C) into wood dowel holes on left side panel (6), right side panel (7) and 2 divider
boards (8).
3. Attach bottom board (5) to left side panel (6), right side panel (7), back board (9) and 2 divider boards (8)
by inserting wood dowels (C) into wood dowel holes on bottom board (5) and make sure back board (9)
is in groove on bottom board (5).
4. Insert 4 screws (E) through holes on bottom board (5), then tighten to left side panel (6) and right side
panel (7).
STEP 6
1. Attach 4 metal legs (11) to bottom board (5) by inserting 8 machine screws (F) through the holes on
shims (H), then through the holes on metal legs (11) and tighten to bottom board (5).
2. Attach middle support leg (12) to bottom board (5) by inserting 2 machine screws (G) through the
holes on the middle support leg (12) and tighten to bottom board (5).

STEP 7
1. Place cushion (10) on cabinet.
ATTENTION ADULTS: Cabinet should be checked periodically for damage or loose
screws/parts.Take appropriate action necessary to correct hazards such as tightening
of screws and taking any damaged parts away from children.
WARNING Please make sure your item is
secured to the wall, per assembly instructions.

Enjoy your new RiverRidge® Bench!
Thank you for purchasing this RiverRidge® Home item. We hope you
enjoy it and consider purchasing other RiverRidge® items.
To order replacement parts at no cost to you, email [e-mail],
call 1-(844)-223-5201 or order parts online at www.riverridgehome.com
RiverRidge® is a registered trademark of Sourcing Solutions, Inc., Hudson,WI 54016