RiverRidge 16-024 Quick start guide

ASSEMBLY INSTRUCTIONS
RiverRidge® Woodbury Storage Cabinet
with Cubbies and Drawer
ITEM #: 16-024
ADULT ASSEMBLY REQUIRED
This product requires assembly by an adult because of small parts. Care should be taken
in unpacking and assembling this item to keep small parts away from children. During assembly
children should be kept away from the product due to possible risk of injury.
WARNING SEE FULL WARNING ON PAGE 2
Young children can be seriously injured or killed if furniture tips over. Don’t use
this item for a TV stand or place heavy objects on top of item. Always use
angle-braces or anchors to secure furniture to the wall.

THIS SHELF UNIT WILL HOLD UP TO 20 POUNDS PER CUBBY AND TOP BOARD AND 10
POUNDS PER DRAWER FOR A TOTAL OF 130 POUNDS. DO NOT LOAD CUBBIES OR TOP
BOARD WITH MORE THAN 20 POUNDS OR DRAWER WITH MORE THAN 10 POUNDS.
OVERLOADING WITH MORE THAN 20 POUNDS PER CUBBY OR TOP BOARD OR 10
POUNDS PER DRAWER MAY CAUSE SHELF TO TIP FROM WALL AND CAUSE DAMAGED
TO THE SHELF OR SERIOUS INJURY OR DEATH.

PARTS LIST
NO
QTY
DESCRIPTION
1
1PC
Top Board
2
2PCS
Divider Board
3
1PC
Top shelf
4
1PC
Middle Shelf
5
1PC
Open Shelf
6
1PC
Bottom Board
7
1PC
Left Side Panel
8
1PC
Right Side Panel
9
1PC
Upper Back Board
10
1PC
Middle Back Board
11
1PC
Lower Back Board
12
4PCS
Metal Leg
13
1PC
Drawer Front Board
14
1PC
Drawer Left Side Board
15
1PC
Drawer Right Side Board
16
1PC
Drawer Back Board
17
1PC
Drawer Bottom Board

TOOLS NEEDED FOR ASSEMBLY: FLAT & PHILLIPS SCREWDRIVER (NOT INCLUDED)
THE USE OF A POWER SCREWDRIVER IS NOT RECOMMENDED FOR ASSEMBLY
DO NOT USE ITEM IF ANY PARTS ARE MISSING OR DAMAGED
To order replacement p a r t s a t n o c o s t t o y o u , e m a i l [e-mail], call
1-(844)-223-5201 or order parts online at www.riverridgehome.com. Only valid in the United States.
If purchased outside of the United States, please contact retailer where purchased.
NO
PART
QTY
DESCRIPTION
A
24PCS
Cam Bolt
B
20PCS
Cam Lock
C
4PCS
Wood Dowel
D
4PCS
Screw (4x35mm)
E
8PCS
Machine Screw (6x30mm)
F
8PCS
Washer
G
1PC
Drawer Slide (Attach to Left Side Panel)
H
1PC
Drawer Slide (Attach to Drawer Left Side)
I
1PC
Drawer Slide (Attach to Right Side Panel)
J
1PC
Drawer Slide (Attach to Drawer Right Side)
K
14PCS
Screw (3x12mm)
L
24PCS
Screw (2.5x10mm)
M
1PC
Handle
N
2PCS
Machine Screw (4x18mm)
O
4PCS
Drawer Cam Lock
P
2PCS
Adjustable Anchor Bracket
Q
2PCS
Screw (4x14mm)
R
2PCS
Plastic Anchor
S
8PCS
Screw (4x35mm)
T
2PCS
Screw (4x30mm)

STEP 1
1. Screw 6 cam bolts (A) into cam bolt holes on left side panel (7).
2. Attach drawer slides (G) to left side panel (7) by inserting 4 screws (K) through holes on
drawer slides (G), then tighten to left side panel (7).
STEP 2
1. Screw 6 cam bolts (A) into cam bolt holes on right side panel (8).
2. Attach drawer slides (I) to right side panel (8) by inserting 4 screws (K) through holes on
drawer slides (I), then tighten to right side panel (8).
STEP 3
1. Screw 6 cam bolts (A) into cam bolt holes on top board (1).
2. Attach 2 brackets (P) to top board (1) by inserting 2 screws (Q) through holes on brackets
(P), then tighten to top board (1).
3. Screw 2 cam bolts (A) into cam bolt holes on top shelf (3).

STEP 4
1. Screw 4 cam bolts (A) into cam bolt holes on drawer front board (13).
2. Attach handle (M) to drawer front board (13) by inserting 2 machine screws (N), then tighten
to handle (M).
STEP 5
1. Attach drawer left side board (14) to drawer back board (16) by inserting 2 screws (S)
through holes on drawer left side board (14), then tighten to drawer back board (16).
2. Attach drawer right side board (15) to drawer back board (16) by inserting 2 screws (S)
through holes on drawer right side board (15), then tighten to drawer back board (16).

STEP 6
1. Slide drawer bottom board (17) into grooves on drawer left side board (14), drawer right side
board (15) and drawer back board (16).
2. Attach drawer front board (13) to drawer left side board (14), drawer right side board (15)
and drawer bottom board (17) by inserting 4 cam bolts (A) into cam lock holes on drawer left
side board (14) and drawer right side board (15) and make sure drawer bottom board (17) is
in groove on drawer front board (13).
3. Insert 4 drawer cam locks (O) into cam lock holes on drawer left side board (14) and drawer
right side board (15), then rotate clockwise to secure cam bolts in place.
STEP 7
1. Attach drawer slides (H) and drawer slides (J) to bottom of drawer by inserting 6 screws (K)
through holes on drawer slides (H) and drawer slides (J), then tighten to the bottom of
drawer.

STEP 8
1. Attach top shelf (3) to divider board (2) by inserting 2 screws (S) through holes on top shelf
(3), then tighten to secure divider board (2).
STEP 9
1. Attach another divider board (2) to top shelf (3) by inserting cam bolts (A) into cam lock
holes on divider board (2).
2. Insert 2 cam locks (B) into cam lock holes on divider board (2), then rotate clockwise to
secure cam bolts (A) in place.
3. Attach middle shelf (4) to divider board (2) by inserting 2 screws (S) through holes on middle
shelf (4), then tighten to secure divider board (2).

STEP 10
1. Attach pre-assembled top shelf (3) and middle shelf (4) to left side panel (7) by inserting cam
bolts (A) into cam lock holes on top shelf (3) and middle shelf (4).
2. Insert 4 cam locks (B) into cam lock holes on top shelf (3) and middle shelf (4), then rotate
clockwise to secure cam bolts in place.
3. Attach open shelf (5) to left side panel (7) by inserting cam bolts (A) into cam lock holes on
open shelf (5).
4. Insert 2 cam locks (B) into cam lock holes on open shelf (5), then rotate clockwise to secure
cam bolts in place.
STEP 11
1. Attach right side panel (8) to top shelf (3), middle shelf (4) and open shelf (5) by inserting
cam bolts (A) into cam lock holes on top shelf (3), middle shelf (4) and open shelf (5).
2. Insert 6 cam locks (B) into cam lock holes on top shelf (3), middle shelf (4) and open shelf
(5), then rotate clockwise to secure cam bolts in place.

STEP 12
1. Insert 4 wood dowels (C) into wood dowel holes on left side panel (7) and right side panel (8).
2. Attach bottom board (6) to left side panel (7) and right side panel (8) by inserting wood
dowels (C) into wood dowel holes on bottom board (6).
3. Insert 4 screws (D) through holes on bottom board (6), then tighten to left side panel (7) and
right side panel (8).
STEP 13
1. Attach 4 metal legs (12) to bottom board (6) by inserting 8 machine screws (E) through holes
on 8 washers (F), then through holes on metal legs (12) and tighten to bottom board (6).

STEP 14
1. Attach top board (1) to left side panel (7), right side panel (8) and divider board (2) by
inserting cam bolts into cam lock holes on left side panel (7), right side panel (8) and divider
board (2).
2. Insert 6 cam locks (B) into cam lock holes on left side panel (7), right side panel (8) and
divider board (2), then rotate clockwise to secure cam bolts in place.
STEP 15
1. Attach upper back board (9), middle back board (10) and lower back board (11) to back of
cabinet by inserting 24 screws (L) through holes on upper back board (9), middle back board
(10) and lower back board (11), then tighten to back of cabinet.

STEP 16
Option #1: Securing to Drywall
1. Position cabinet against wall in desired location. Using a pencil, make 2 small marks on wall
through holes on brackets (P). Move cabinet away from wall and screw 2 plastic anchors (R)
into wall on pencil marks.
2. Place cabinet against wall, insert 2 screws (T) through holes on brackets (P), then tighten to
plastic anchors (R).
Option #2: Securing to Drywall and Wood Stud
1. Position cabinet against wall in desired location. Insert 2 screws (T) through holes on brackets
(P), then tighten through drywall and into wood stud.
*Tip: Anchor brackets (P) can be adjusted to correct distance from wall to cabinet as needed. Once
adjusted, be sure to re-tighten brackets inside cabinet for stability.

STEP 17
1. Slide drawer into cabinet.
ATTENTION ADULTS: Cabinet should be checked periodically for damage or
loose screws/parts. Take appropriate action necessary to correct hazards such as
tightening of screws and taking any damaged parts away from children.
WARNING Please make sure your item is
secured to the wall, per assembly instructions.
CARE INSTRUCTIONS:
Wipe clean with a water dampened cloth. Wipe dry with clean cloth.
IMPORTANT:
Keep assembly instructions for future reference.

Enjoy your new RiverRidge® Cabinet!
Thank you for purchasing this RiverRidge® Home item. We hope you
enjoy it and consider purchasing other RiverRidge® items.
To order replacement parts at no cost to you, email [e-mail], call
1-(844)-223-5201 or order parts online at www.riverridgehome.com. Only valid in the United States.
If purchased outside of the United States, please contact retailer where purchased.
RiverRidge® is a registered trademark of Sourcing Solutions, Inc., Hudson, WI 54016