Riverside Furniture Verona User manual

1 pc.
Queen Storage Footboard
Hardware and Parts packed with the Footboard
Hardware and Parts packed with the Bed Rails
Queen Storage Bed
Assembly Instructions Made in Viet Nam
Slat Support Leg
13" long
Page 1 of 3
4 pcs.
R-E
R-E
5/0-6/6 Queen-King Bed Rails
2 pcs.
F-A
F-C F-D
R-A
Detail: C
5/0 Wood Slat
61-5/8" long
F-B 4 pcs.
Ø9 x 1"
Wood Screw
Platform Panels
61" x 20"
4 pcs. F-E 28 pcs.
F-J
F-G
F-H
F-I
F-F
Detail: D
Riverside
FURNITURE
email: [email protected]
8 pcs.
R-B 1 pc. 8 pcs.
5/16-18 Nut 12 mm Open
Wrench
Ø5/16-18 x 4" Long
All-thread Bolt
R-D R-E
5/16" Curved
Washers
R-C
8 pcs. 1 pc.
R-F
Ø5 mm
Wrench
Storage Box
Support Leg
2 pcs.
Ø1/4" x 1-1/4 "
Allen Head Bolt
4 pcs. 4 pcs.
Ø1/4" Spring
Washer
Ø1/4" x 16mm
Flat Washer
4 pcs. 1 pc.
4mm Allen
Wrench
F-F F-G F-H F-I F-J
Light Sienna Finish (#246) or Dark Sienna Finish (#249):
A 5/0 Queen Size Storage Bed can be configured using
the 5/0-6/6 Bed Rails and either style of Headboard and
the 5/0 Storage Footboard.
Storage Bed Shown:
24670 / 24970 -- 4/6-5/0 Panel Headboard
24673 / 24973 -- 5/0 Storage Footboard w/Panels
24672 / 24972 -- 5/0-6/6 Bed Rails
ASSEMBLY STEPS:
1. Carefully lean the back of the Headboard
against the wall where it will be used. Install
the Ø5/16" x 4" Long All-Thread Bolts (R-E)
into the threaded inserts of the Headboard and
Footboard (See Detail C).
2. Attach the Storage Box Support Legs (F-F) to
the Storage Box using the Bolts (F-G), Spring
Washers (F-H) and Flat Washer (F-I). Tighten
with the Allen Wrench. (F-J).
Note: For a Storage Bed, the Slat Support Rail mounted on the
Bed Rails must be located at the upper position. Using the Allen
Wrench (R-J), remove the Bolts attaching the Rail and move.
Verona

Page 2 of 3
Made in Viet Nam
Queen Storage Bed
Assembly Instructions
ASSEMBLY STEPS :
To prevent possible damage to furniture and personal injury, it is recommended that two people are used
to perform the following steps.
3. Carefully position one end of one Bed Rail (R-A) onto the All-thread Bolts installed on the Headboard
and connect using the Curved Washers (R-B) and Nuts (R-C). Only partially tighten the Nuts until the
Footboard has been connected. Repeat for other Bed Rail.
4. Position and connect the Footboard (F-A) to the other end of the Bed Rails, attaching as in the previous
Steps.
5. Carefully align the Footboard to be 'square' with the Headboard. Using the Open Wrench (R-D)
tighten all Hex Nuts attaching the Side Rails to the Headboard and Footboard. (See Detail E).
6. Attach the four Support Legs (F-C) to the bottom side of four Wood Slats (F-B). (See Detail F).
7. Using the Platform Panels (F-D) as a guide, position the Slats where the edges of the panels will be
supported, attach the Slats to the Bed Rails using the Wood Screws (F-E) and your Phillips
Screwdriver (See Detail G).
8. Position and attach the Platform Panels to the Bed Rails using the Wood Screws (F-E) and your
Phillips Screwdriver (See Detail H).
The levelers located at the bottom of the Support Legs can be adjusted if necessary to help support the
Slats.
Bed rail Detail: E
Bed rail
Footboard
Headboard
Detail: F
F-C
F-B
8 pcs.
4 pcs.
R-A
F-E
F-A
Detail: G
R-A
R-C
R-D
leveling
R-B
Riverside
FURNITURE
email: [email protected] Verona

Page 3 of 3
Made in Viet Nam
F-E
Platform Panels.
F-D
Detail: H
Riverside
FURNITURE
email: [email protected]
Position Slats
underneath
edge of Panels
Verona
Queen Storage Bed
Assembly Instructions