Robam CXW-200-A822 User manual

A822
Operation Manual
Range Hood
CXW-200-A822

CONTENTS
1.Important Information...........................................1
2.Product Overview.................................................1
3.Installation............................................................2
4.Use Instruction....................................................5
5.Maintenance and Services.................................7
6.Circuit Diagram....................................................9
7.General Troubleshooting......................................9

1
Improper operation may cause hazardous effect.
Picture 1
≥230
895×520×600(mm)
Decorative tube
Switch
16.5 m/min
3
+1
-2
56.5dB≤
CXW -200 -830 2
CXW-200-A822
≤2W
≥22%
Dear Users
Thank for your buying our range hood. Please accept our best regards.
Please read this operation manual carefully before installation and operation.
Important Information
Product Overview
New Package of Range Hood
Please settle those packages carefully in order to protect environment.
Don’t allow children to play plastic film and package, it may cause asphyxia. Please avoid children near package
material.
Dispose Old Range Hood
If the old range hood can’t work, we suggest users to dispose them after confirming without any usage.
There are something useful material inside of old range hood, please assist us to dispose so as to protect environment.
Before use new range hood
This range hood exhaust fume outside.
Please read this manual and all information carefully before installation and operation. Please comply with our
suggestion. If it’s necessary, please read manual for gas hob. And please keep these manual carefully for future reference.
This manual is available for different models. So you may find different description with your own range hood.
If range hood has obvious damage, please don’t electrify and contact operator.
Children and disability are not allowed to use range hood independently in order to avoid accident.
26kg
Notice： Operation function for stir fry, the power and speed than strong file (3 files) power and speed increased
by 10%.
Size( L x W x H)
Technical Datas
Model
Power Supply
Total Pressure Efficiency
Nominal Wind Pressure
Air Flow Rate
220-240V~ 50Hz
Pa
Noise
Rated Main Motor Input Power
Lighting Power
Net Weight
200W
A822
Range Hood

Installation
Warning
1.The range hood is prohibited from exhausting fume into hot flue ,which is used for exhausting gas fuel or
other fuel fume.
2 In installing metal expansion tube ensure perfect match of tube diameter with hole diameter to prevent
accidental falling off loosened expansion tube due to excessive hole expansion
3 Use range hood in case of gas or other fuel combustion and ensure ventilation in the room
4 Flue opening smaller than that of the air duct or excessively long air duct will affect the fume removal
. ,
from .
. good .
. .
Preparation
Size & Dimension
367
520
Packing List
2
317
895
600(430）
Picture 2
CXW-200-8 302
Note:The lenghth is only for reference，in the brackets of the size is high of draw tube .（size：mm）
Packing List
No.Item Name Quantity No.Item Name Quantity
1
12
11
6
5
4
3
2
Range Hood
Plastic expansion tube
Operation Manual
Check Valve
1 unit
4 pcs
1 unit
ST 4x18 tapping screw 10 pcs
Φ175 aluminum foil's duct ST 4x60wooden screw 4 pcs
13
14
Stop block for bracket 1 unit
10
M6metal expansion tube 1 set
Hanging feet 1 unit
7
Oil Cup 1 pcs
8
Φ175 air duct’s interface
9
Adhesive tape
Fixed bar of air duct 1 set
1 unit
Ambient environment
Range hood shall be installed away from positions with too many windows or doors, which will lead
to strong air convection and thus reduce the effect of fume removal.
Tools
Note: This product must be used in the daily life. Don't use it under special situation(for example:
outside ), meanwhile ,don't use this product to exhaust dangerous explosive material or gas . This
product must be placed under safe circumstance before installation. (dry, good ventilation,non-
corrosive and innoxious ,etc)
!
Installing range hood requires the following tools:1.impact electric drill(with drill bit) ;2.Wrench;
3.Screwdriver;4.Ruler
A822
Range Hood

Installation Precautions
Don't install the range hood too high and
keep it free from external airflow to prevent
reduced the effect of fume removal.
Please reserve sufficient space when
making cabinet in order to maintain and
repair hood.
Keep hood horizontal when installing.
Picture 7
Please use the single-phase grounding socket,
and good.
3
Picture 3Picture 4
Picture 5Picture6
CXW-200-8302
CXW-200-8302
CXW-200-8302
!
Tap water pipe
improperly earthed.
It's dangerous of fire
and explosion to earth
gas pipe.
Picture 8
explosive
Raw water pipe
gas pipe
Please pay much attention to following:
If your kitchen is under installation, please don’t divulge range hood outside, because the smell from building
material, dust, painting, coating material may cause rust. We suggest users to install range hood after decoration.
Don’t allow to install range hood on the wall which is easy to fire, for instance, wooden wall. Please install range
hood on the wall where has enough space and strength for noncombustible material.
Range hood and electricity must be installed by specific operation. Don’t allow to install, disassembly and
maintenance range hood by non-professionable person.
Please ware glove when moving, installing, cleaning or repairing range hood.
Please be care of electricity inside of wall when operator digging holes on the wall. It may causes fire.
Warning:Don't allow to contact fire with range hood
directly. Forbid gas stove from getting fire to prevent
damage of range hood or happening of accident.
Range Hood

520
Picture 9
Top Plate
600-800mm
650-750mm
800-900mm
Draw tube
10mm
Top Plate
Removable plate
Removable plate
600-800mm
650-750mm
800-900mm
10mm
(Picture 9-1 mounting without removable baffle)(Picture 9-2 mounting with removable baffle)
Installation-hole for
draw tube
ST4X18 tapping screw
Decorative
tube
Stop block for brachet
CXW-200-8302
1、Location:Reference dimension for mounting of removable baffle is 430(mm),but subject to adjustment according to actual situations.
The installation hole(picture 10) shall be centered vertically with the hood body and kept horizontally.
Operator shall install range hood upright the gas hob with recommended lowest height between hood bottom and cooktop is 650mm
(if maximum installation distance is specified in the instruction of installation, this shall be taken into consideration; The installation height
can be reduced according to actual situations when there is electric hob).
Mounting
(Don’t require to adjust and install draw tube in Picture9-2)
CXW-20 0-A801 CXW-20 0-A801
Installation
4
2.Installing hanging plate: Drill four 60-70mm-deep holes by Ф8mm drill bit at positions corresponding to the
hanging plate dimension. Force the expansion tube into the holes and fasten firmly the hanging plate by the
supplied four 4x60 wooden screw. Drill a 50-55mm-deep Ф10mm hole at position 65mm high from the four
holes and force the M6 metal expansion tube into the hole(picture 10).
Installing hood body: F as shown in Picture 10, align the hanging holes
at back of the hood body to the hooks on the hanging plate and slide the body in by pressing and shake by
hands the body to see if it is firmly hang. When the body is ready in place, install safety stop block and gasket
on the M6 metal expansion tube and fasten firmly the nuts to prevent the hood body from running out of the
hooks under external force.
5.
3.Adjust draw tube:Pull up two brackets of the draw tube to proper level, then forced pull out the draw tube, ear off
the protective film. And then insert into between decorative tube and shell body to adjust the proper level.
4.irst fix the check valve as picture 11-1
Install draw tube:Following picture 9-1, a gap is about 3cm between draw tube and top plate, push the draw tube, so
that the draw tube can touch the top plate, and then fix the draw tube on the top plate with ST 4x18 tapping screw.
35±2mm
235mm
65±2mm
110mm
55mm 55mm
565mm
113mm
458mm
520mm
895mm
Picture 10-1Picture 10-2
Hood top
projection size
Wind pipe hole sizeφ200mm wall
Ceiling hole size chart
A822 A822
A822
Range Hood

Use Instruction
Control Panel
5
Picture 12
slight Timing switch Stir fry Air volume power
Timing display Air volume display
A822
Range Hood
Picture 11-1
Firstly, fasten one side of aluminum foil’s air duct without fixed bar on the interface by adhesive tape, then straighten
air duct with the interface of public flue and connect it. (Without public flue, please straighten air duct outside of room.
When the interface of public flue or the size of wall’s hole is bigger than aluminum foil’s air duct, it can be connected
directly; When it’s smaller, there are four specification for the interface of air duct, such as 140mm, 150mm, 160mm and
170mm. The users can cut additional parts based on actual situations.
Then, fasten one side of aluminum foil’s air duct with fixed bar in the external ring of check valve by adhesive tape.
Finally, put 4 fasteners on the interface of check valve into corresponding groove, and fasten air duct on the check
valves clockwise.
Check valve interface
Φ180 Φ170 Φ160 Φ150
Φ140
Fastener
Groove
2) Connect aluminum foil’s air duct
Φ175 aluminum foil's air duct
Adhesive tape Φ175 air duct's interface
cut additional part which smaller than wall's hole
Notice: Please straighten the aluminum foil's air duct when installing
this product to avoid noise under incompletely straight condition. The
additional air duct can be cut by wire-cutter.
Check valve
Body of machine
Seal ring of check valve
ST4X18 screws
Adhesive tape
The hole diameter on the wall shall be near to that of air duct and shall not be too small. Otherwise, it will lead
obstructed exhaust, higher noise and lower air flow rate. The interface between air duct and check valve or public
flue must be sealed completely and connected firmly. The sheet on the interface of check valve or pubic flue’s
interface must move smoothly.
6. Install aluminum foil’s air duct:
1) Drill hole position for aluminum foil (for public flue, don’t need to drill holes)
a. Aluminum foil and cooktop faces to window: disassemble one side glass, and install one plywood with holes, or
open holes on the glass directly.
b. Cooktop keeps far away from the window: Select the window nearest to the outside with good ventilated to install
aluminum foil across the window; Or drill hole on the wall nearest cooktop and install aluminum foil across the wall.
c. Drill holes on the wall: measure aluminum foil’s position on the wall, draw the hole’s scope on the wall ( circles
slightly larger than the diameter of aluminum foils), then drill holes through the wall. Don’t destroy the outside wall,
so when drill holes, please take care of wall’s structure and materials.
Picture 11-2

6
Switch off the plug in case of no time no use.
Picture 20Picture 19
Pull out the oil cup and discharge
the waste oil.
Picture 16
Picture 18
Picture 17
After ensuring power is on, lightly touch "Light"
key by finger, its lamp turns on and press "Light"
key again, its lamp goes out.(Lighting lamp turns
off)
Press the timing button,the timing display shows"1",means timing is 10mins,the range hood will send out the
"Ding" sound to remind the timing is over.Press again ,the timing dispaly shows "2",means thiming is 20mins,until
60mins.If the timing is over,press any button to cancel the reminder of the timing.
Display "6" when press the stir-fry button and change to "3" automatically after 3mins,then you can adjust the
air flow rate button to change the air flow rate ,the buzzer will ring by press each time with air flow rate reduce.
Picture 15
key by finger, its lamp turns on and press "Light"
key again, its lamp goes out(Lighting lamp turnsoff);
If the motor is running,touch "power"button,the
"power"button will be shine and range hood shall
be turn off motor functions after 1 mins.If the “power"
button shine,press the "power"button again to swith
off all functions.
After ensuring power is on, lightly touch "Light"
A822
A822
Range Hood
Picture 13 Picture 14
Turn on the power plug, a buzzer rang 3 sound prompted
to install qualified, into standby mode.
Press the power button, the outer circle give red lights, the
products are in boot state, ready, waiting for work instructions.

For safety concern , do not wash the range
hood by water spray.
Wipe with wet cloth soaked in neutral detergent.
Picture 21 Picture 22
7
Maintenance and Services
Dismounting of lamp
Picture24Picture23
Pull out of lamp from cover and take out of connector,
then replace lamp.
Remove fastening screws of lamp shade plate by
screwdriver.
CXW-200-8302 CX W-200-8302
Note: mounting of lamp and switch is just opposite to dismounting them.
If not wash in the way specified methods in the instruction, range hood may be liable of fire.
Range hood shall be cleaned at regular intervals depending on the environmental conditions to keep clean
and extend service life
To ensure smooth fume removal,oil guide mesh should be cleaned every month.Impeller should
be cleaned once every year by professionals.
good effect,it's helpful to .
Our suggestion:
Warning:Maintenance and cleaning shall be carried out after unplug the plug.And the electric parts must avoid
water.
A822
A822
A822
Range Hood

8
Mounting and dismounting
Picture 26
Impeller
Cap
Air flue
Motor
Baffle ring
Cover pla te
Draw tube
Decoreative
tube
Oil cup
Oil guide mesh cover
Oil guide mesh
Dismounting Steps:
1.Pull out power plugs;
2.Screw off 4 screws behind the decorative tube and incline the decorative tube forward to
certain angle and pull it out by force with hands;
3.Take out draw tube from the decorative tube;
4.Remove the cover plate after screwing off the fastening screws by Philips screwdriver;
5.Remove the baffle ring after screwing off its fastening screws;
6.Screw off cap cover clockwise and vertically take out impeller;
7.Remove fastening screws on the safety net by Philips screwdriver and take out oil cup
and oil guide mesh.The assembly steps are just opposite to the nondisassembly. (In
assembling impeller, apply lubricant to the axle hole of the impeller. )
Notice: Don't follow with step 3 without draw tube.
A822
Range Hood

9
Circuit Diagram
General Troubleshooting
EL:
M:
XP:
K2:
K1:
K3:
C:
E:
K4:
K5:
1.When connecting accessory
or replacing bulb, please
pull out power plug;
2.If power wires of range
hood damaged, replace
them by professionals;
3.Don't allow to exhaust
flame through range hood.
Warning
Lamp damaged or improperly
contacted
Loose impeller,cap not properly
fastened
Plugs improperly plugged or
power off
Plug improperly earthed
Reasons
No reaction in pressing any switch(such as
impeller does not run and lamp does not light)
Lamp fails in pressing lighting switch
Induction current on hood surface
Abnormal impeller sound
ProblemNo.
1
2
3
4
No oil in oil cup after some time Inclined installation of hood
body
5
lamp
Motor
Capacitor 500VAC 5
High Switch
Middle Switch
Power Plug
Earthing Terminal
Low Switch
Lighting Switch
Stir fry Switch
Warning
There shall be adequate ventilation of the room when the range hood is used at the same time as appliances
burning gas or other fuels .
- Do not flambe under the range hood.
- Regulations concerning the discharge of air have to be fulfilled.
- This appliance is not intended for use by persons (including children) with reduced physical, sensory, or
mental capacities, or lack of experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for their safety.
- Children should be supervised to ensure that they do not play with the appliance.
- If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly
qualified persons in order to avoid a hazard.
Accessible parts may become hot when used with cooking appliances
The minimum distance between the supporting surface for the cooking vessels on the hob and the lowest
part of the range hood. When the range hood is located above a gas appliance, this distance shall be at least
65 cm. If the instructions for installation for the gas hob specify a greater distance, this has to be taken into
account.
-
-
Range Hood
Yellow/Green E

Edition: A/1