Robam CXW-200-A810 User manual

8321
Range Hood
CXW-200-A810
CXW-200-A605
Operation Manual

1.Important Information.........................1
2.Product Overview...............................1
3.Installation..........................................2
4.Use Instruction..................................6
5.Maintenance and Services...............6
6.Circuit Diagram..................................9
7.General Troubleshooting....................9
CONTENTS

8321
1
This mark means warning contents, Improper operation may cause accident.
图1
Panel
Switch
Oil Cup
Dear users:
Thank for your buying our range hood. Please accept our best regards.Please read this operation manual
carefully before installation and operation.
*The pictures in this manual only for your reference. If the picture isn’t accord with object, subject to object. We
keep to right to update appearance, structure or products without notice.
Important Information
Product Overview
New Package of Range Hood
Dispose Old Range Hood
Before use new range hood
If the old range hood can’t work, we suggest users to dispose them after confirming without any usage.
There are something useful material inside of old range hood, please assist us to dispose so as to protect environment.
Please settle those packages carefully in order to protect environment.
Don’t allow children to play plastic film and package, it may cause asphyxia. Please avoid children near package
material.
This range hood exhaust fume outside.
Please read this manual and all information carefully before installation and operation. Please comply with our
suggestion. If it’s necessary, please read manual for gas hob. And please keep these manual carefully for future
reference.
This manual is available for different models. So you may find different description with your own range hood.
If range hood has obvious damage, please don’t electrify and contact operator.
Children and disability are not allowed to use range hood independently in order to avoid accident.
Know the range hood
Oil Mesh
Range Hood

322
505(440)
2
359
895(595)
5 3 7（5 2 9）
The marked sizes are for reference only. Size in the brackets is specific to A605 hood. But the drawing
panel height shall be 430 of A810.(Unit: mm)
Packing List
No.Name Quantity No.Name Quantity
1
12
11
6
5
4
3
2
Range Hood
Plastic expansion pipe
Manual
1 piece
4 pieces
1 piece
Check valve 1 set
ST4x18 self-tapping screw 10 piece
Φ175(OD) aluminum exhaust screw
13
14
ST4×60 wood screw 4 pieces
10
Hitching foot stopper 1 piece
M6 metal expansion pipe 1 pair
7Oil cup 1 piece
Hitching foot 1 piece
Φ175 ( OD) exhaust pipe joint
9
Exhaust pipe tape
Fixed bar for exhaust pipe
1 set
Packing List
Please check lists if open the package.
≥220Pa
A810:895×505×537(mm)
A605:595×440×529(mm)
Rated input power of the main motor
55dB
≥23%
A810：21.5kg A605: kg
A810:≤2W 2
A605:≤1.5W 2
×
×
Dimensions (L×W×H)
Maximum static pressure
Odor decrease rate ( normal)Odor decrease rate ( instantaneous )≥76%
≥310Pa
≥98%
Rated input power of the hood
A810:204W A605:203W
200W
Grease separation rate ≥92%
Noise
Maximum input power of the light
Net weight of the hood
Model
Power Supply
Total Pressure Efficiency
Nominal pressure
Air flow rate
220-240V~ 50Hz
1.The deviation between the specified value and actual value of airflow shall not exceed 10% of the
specified value.
CXW-200-A810
CXW-200-A605
Body Size
Size & Dimension
3
17m /min
8
Range Hood

3
Installation
1.Flue gases shall not be discharged to the hot flue, which is exclusively used for discharging the combustion gas or
other fuel fumes.
2.Note that when installing the metal expansion pipe, the pipe shall match perfectly with the hole in size.
Overlarge hole is prohibited, as it will result in loose pipe and accidental drops.
3.If the hood is used together with a cooking hob burning gas or other fuels, the room must be well ventilated.
4.Flue diameter smaller than that of the exhaust pipe will affect the hood efficiency. So will overlong exhaust pipe.
5.Regulations concerning the discharge of air have to be fulfilled.
●
●
Surroundings
Keep the hood away from too many doors and windows, so as to avoid air convection affecting the efficiency.
Tools
The hood will be installed with the following tools: 1). an impact drill (with drill bit); 2). a wrench;
3). a screwdriver; and 4). a ruler.
Warning
Preparation for Installation
Installation Notes
●
●Don't connect power before installation,it may cause electric shock.
●
●
●
●Don't install range hood too high and protect it from airflow interference, so as not to reduce efficiency.
●When making cupboard, save room for hood body to facilitate the maintenance and repair.
●
●Use suitable plug and well grounded. (Water pipe isn't grounded well and gas pipeline grounded may cause
fire and explosion).
●Use appointed accessories for installation or range hood may fall down and cause danger.
●
●If finish installation, clean range hood firstly, then connect power and test run.
Installation and circuit setting must be done by experienced professionals. Non-professionals are not
allowed to install, dismantle and repair the hood.
●Don’t expose the hood if your kitchen is under renovation, because construction materials, dusts, paint,
coatings, and emitted gases will corrode and tarnish the hood surface. Therefore, it is recommended to
install it after the renovation is completed.
Don' t install the hood on wood and other combustible walls. The wall shall be made of noncombustible
materials with enough strength.
The hood may have very sharp edges. So, please wear protective gloves during hood installation, cleaning
or repair.
When drilling on the wall, keep away from embedded wires to avoid fire.
During installation, please keep the body level.
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly
qualified persons in order to avoid a hazard. Don't stretch, change ,tie, or press supply cord, or it may cause
fire or electric shock.
Range Hood

4
505(440)
Figure1
Ceiling
600-800mm
650-750mm
800-900mm
Drawing panel
10mm
Ceiling
Removable panel
Removable baffle
600-800mm
650-750mm
800-900mm
10mm
( Figure 1-1 Installation method of hood without removable baffle)
( Figure 1-2 Installation method of hood with removable baffle)
Mounting hole
of the drawing
panel
ST4X18 self-tapping
screws
Decorative panel
CXW-200-831 2
●
T
Determine the position:
he size of removable baffle ( reference:430mm) can be adjusted according to the actual situations. The installation pitch of
holes is shown in Figure2. The hook body shall be centered vertically and kept level. Ceiling hole size is shown in Figure3.
The hood shall be installed upright the hob. The minimum distance between the bearing surface of cooking appliance and
the lowest part of hood is 650mm (larger space specified in the installation instruction of gas hob shall be considered, if any;
the distance for electric cooker may be reduced appropriately, depending on the actual situations) .
Note:A605 is the small size hood, we suggest to use it with single burner hob.
Installation
Figure 2
Hitchi ng foot
235mm
110mm
55mm 55mm
495mm 65±2mm
35±2mm
Hitching foot stopp er
CXW-200-8312
Figure 3
100mm
468(318)mm
Ceiling drilling size chat
(The size of A605 in the bracket)
505(440)mm
895(595)mm
Projection size of
the hood top
Wall
Hole size of the exhaust pipe Φ200mm
●Install hitching foots:
According to the size of the hitching foots, drill four 60-70mm- deep holes on the wall accordingly with an 8mm- diameter drill bit ( overlarge holes are
prohibited) . Press the expansion pipe into the holes, and then fix the hitching foots with 4 accompanying ST4X60 wood screws. At 65mm above the four
holes, drill a hole of 10mm- diameter and 50-55mm depth (overlarge holes are prohibited).Insert the M6 metal expansion pipe into the hole. ( As shown in
Figure 2)
8321 8321
8321
Range Hood

5
The hole diameter shall be close to that of the exhaust pipe. Undersized hole will cause poor exhaust efficiency,
more noises and lower airflow. The connection between the pipe and the hole or the public flue must be sealed tightly
to ensure that, the pipe and the check valve or public flue is connected securely. The blades at the check valve
connection or public flue connection must be flexible.
Figure 4
Hood body
Check valve
Check valve connection
ST4 x 18 screw
Check valve seals
Note: During installation, straighten the aluminum exhaust pipe to avoid noises
in semi-stretched state. Excess part may be cut with a wire cutter.
Snap
Slot
●The drilling size of aluminum exhaust pipe(No need to drill hole for the public flue)
a).Aluminum exhaust pipe and hob facing the window: To remove one of the glasses and install a plywood with ventilation
holes or punch directly on the glass.
b).Hob away from the window: To install the aluminum exhaust pipe through the window that is close to the hob and connected
outside, or install it by punching on the wall that is close to the hob and connected outside.
c).Drill hole through the wall: Determine the location of the aluminum exhaust pipe against the wall and draw the drilling
range (i.e a circle slightly larger than the pipe OD).Use a long drill bit to drill through the wall. Pay attention to the wall structure
and material, so as not to destroy other parts of the wall.
Insert the other pipe end to the pipe connection and stick with tapes. Straighten the aluminum exhaust pipe to the
outdoors.This can be done directly when the wall hole is larger than the pipe.Otherwise, there are four pipe
ends(OD:140,150,160,and 170 respectively) to be chosen from according to the hole size.Then cut the excess part with
scissors.
Then, insert one of the ends in the outer ring of the check valve connection and seal with exhaust pipe tapes. Finally, put four
snaps of the check valve connection in corresponding slots, and rotate them clockwise to fix the exhaust pipe to the check valve.
●Connect aluminum exhaust pipe
Φaluminum exhaust pi pe175
Exhaust pipe tape Φex haust p ipe connection175
Cut the excess p art sma ller than the hole
Φ180 Φ170 Φ160 Φ150
Φ140
Exhaust pipe tape
Install the aluminum exhaust pipe:
Figure 5
●
●
●
As shown in Figure1-1, there are some gap between the drawing panel and the top plate. Push the panel against the top plate and then
fix it to the top plate with ST4x18 screws.(If installation method in Figure1-2, there’s no need to adjust and install the drawing panel).
Note: If there is no drawing panel, no need to adjust or install it.
Adjust the drawing panel:
Pull the brackets of the panel up to an appropriate height and then pull the panel sides to find the drawing panel. Remove the protective film,
and insert it along the gap between the decorative panel and the housing. Then adjust it to the proper height.
Install the hood body: fix the check valve as shown in Figure 5. Then direct the hanging holes in the back of hood at the hooks of hitching
foots according to Figure 2, and press them together. Shake the body to check if it's hung securely. After the body is mounted, install the
hitching foot stopper and gaskets to the M6 metal expansion pipe, and then tighten the nuts ( to prevent accidental decoupling of the body
under external force).
Install the drawing panel:
Range Hood

6
Plug in and three tick from the buzzer will indicate qualified installation. The hood is in standby.
Use Instruction
Lighting
High speed
Low speed
Power
Press the power button, the light of "power "button turn on,press "high speed" button, the motor works
with high speed. If press the "low speed" button, it will work in the normal speed states.
After connect with power, press "power" button the light of "power" turn on, press "low speed",the motor
works with low speed, press "high speed" button again, it will switch into high speed level again.
Lightly touch "Lighting" button by finger, its lamp turns on and press "Lighting" button
again, its lamp goes out.(Lighting lamp turns off)
When the power icon is lit up and only the lamp is “ON”, press the power button
gently and the lamp will be turned off directly; if the fan is working, press the power button,
the power icon will flash and the fan will enter delay status, then shut down after 1min.
(Under delay status, “lighting”, “ high speed” and “low speed” button all can’t work; When
“Power” button flash, press the button again, all functions will be disabled.
Switch Control Panel
After power is on, press "high speed" button, the motor works with high speed. If press the "low speed"
button, it will work in the low speed states.
After power is on, press "lighting" button, lamp will turn on; Press it again, lamp will turn
off;
Under fan working status, press "power" button, fan will stop working; The "power"
button can't control lamp;
High speed
Low speed
Lighting
Power
After power is on, press "low speed" button, the motor works with low speed. If press the "high speed"
button, it will work in the high speed states.
Switch control panel of A810
Switch control panel of A605
Range Hood

Raise it outward forcibly to remove the spotlight from
the hood. Pull out the connector to replace the
spotlight.
Insert a small flathead screwdriver or something
sharp in the gap between the light cover and hood.
7
Note: The light and switch shall be installed or disassembly
in a reverse order.
Remove two screws on the cover, revolve the cover
and pull out switch accessories, then replace or maintain
it.
Remove two screws on the cover, then disassemble
the cover.
CXW- 20 0- 83 01CXW- 20 0- 83 01
1
8321
CXW- 20 0- 83 01
CXW- 20 0- 83 01CXW- 20 0- 83 01
2
8321
Notice
●
●Don ’t use the po wer ful de tergent, we recommen d to wi pe
●Don 't keep dirt on the sur face of range ho od for long time;
●Don 't use cleani ng ba ll, brush or othe r ha rsh tool to clean ran ge hood. It may cau se scoring.
●Wear gl ov es to clean or mai nt ai n range hood avoi di ng from hurt.
●Che ck oil cup reg ul ar ly. If oil ex cee ds 2/ 3 in the cup, mov e the cup by hand as right figu re and pour-out was te oil.
●Don 't touch lamp if turn on or turn off in short time. It may cause scald.
●If range ho od do n’ t use for long time, pull out the plug . Don ’t haul plug crud el y.
The hood shall be cleaned and mai ntai ne d reg ul arly depending on the surroundings, so as to keep its cleanness &
efficiency and ex ten d its service life.
We rec ommen d: To clean the exha us t fume collecting ho od an d ran ge hood body after each cooking .
To en sur e smoo th discha rge of fume s, the filter shall be cleaned regul ar ly wi th war m wat er and de ter ge nt according to
actual situa tions. Be caref ul to avoid damag e.
with wet cloth soa ked in neut ral de tergent and dr y it by soft
cloth. An d av oi d de ter ge nt to touch swi tches.
Light Removal
Switch Removal
1.There is a risk of fire if the appliance is not cleaned according to the methods stated in the instructions.
2.Cleaning and maintenance must be done when the power is disconnected. Keep the electrical components (e.g. motors,
switches and connectors) away from water to avoid accidents. Don’t touch plug, electric parts and switches by wet hands;
3.Normally, hood body don’t need to disassembly. If need, it should be carry out by professionals, and take off plug before
disassembly.
Don't rinse with water to avoid accidents.4.
5.Extinguish fire in time if don't use hob. Prohibit bakerange hood by fire or bake food under range hood directly. It may
cause damage and accident.
6.If the supply cord is damaged, it must be replaced by professionals avoiding from danger.
Warning
Maintenance and Services
Parts Removal
Range Hood

8
Air flue
Removal steps:
1. Pull out the plug;
2. Unscrew the four screws from the back of the decorative panel. Tilt the panel forward to a certain angle, and then
pull it up forcibly;
3. Remove the drawing panel from the decorative panel;
4. Use a Phillips screwdriver to unscrew the fastening screws on the cover to remove the cover;
5. Unscrew the fastening screws on the retaining ring to remove the retaining ring;
6. Unscrew the cap clockwise and take out the impeller vertically;
7.Use a Phillips screwdriver to remove fixed screws, then remove the oil cup and filter mesh
The installation and removal procedure in reverse.
(When mounting the impeller, apply some lubricant to the shaft hole.)
Note: Step 3 is unnecessary if no drawing panel is installed.
Motor
shell
Dec orative pane l
Drawi ng pane l
Oil cup
Retainer ring
Impeller
Cap
Cover plate
Filter mesh
Filter
Switch
Top cover plate
8321
Note: When installing the filter mesh, put the side with screw holes inward.
Filter Mesh Removal
Hood Body Disassembly Steps
Align the Phillips screwdriver wit the screw hole and raise
it upward forcibly meanwhile rotating it counter-
clockwise about 1 20°, so as to remove the screw out of
the cross slot of the exhaust fume collecting hood.
Hold the two screws on the filter mesh and pull it down to
detach the two prongs inside from the exhaust fume
collecting hood. Then pull the filter out in the arrow
direction to remove it.
Range Hood

M
General Troubleshooting
2.If the hood's power cord is
damaged, it must be replaced by
our maintenance staff.
3.Keep the hood away from fire
to avoid accidents.
1.Please unplug the power cord
when connecting the plug-ins or
replacing any part.
Warning
The light is damaged or poorly
connected
The impeller is loose and the cap is
not tightened
The power is not connected properly or
there is power failure
The power outlet is not well grounded
Cause
No response after pressing any button (e.g.
the impeller does not rotate, light is “OFF”)
Light “OFF” after pressing the light button
Induced current on the hood body that
paralyzes hands
Abnormal sound during impeller running
FailureNo.
1
2
3
4
No oil in the oil cup after a period of time The body is tilt
5
For other failures, please contact the vendor, special service center or our service center directly.
9
220-240V
50Hz ~
Circuit Diagram
Brown
Blue
Blue
Black
Orange
Brown
Blue
Red
Blue
Red
Red
Yellow
K1
K2
K3
L
N
EL
EL
L
N
XP
EL
C
EL
M
Circuit Diagram of A810
Circuit Diagram of A605
Brown
Blue
Blue
Black
Brown Red( )
Brown Yellow( )
Blue
Red
Blue
Red
voltag e tran sfo rmer
Off
High
Low
Lighting
Mechanical button
220-240V
50Hz ~
Range Hood
Brown
Orange
Gray
Black
Blue
Yellow/ Green
Yellow/ Green E
Yellow/ Green E
Yellow/ Green
Terminal box
Control circuit
Operating circuit

Edition: A/0