roblight XPO X-LED User manual

Troubleshooting
RobLight accepts no responsibility for possible errors in catalogues, brochures and other printed m aterial.
RobLight reserves the right to alter or discontinue its products w ithout notice. © 2019 RobLight A/S
RobLight A/S, Nordhavnsvej 1A, DK-9900 Frederikshavn
T: [phone], E: info@ rob-lig h t.c o m
www.rob-lig h t.c o m
99082136, 24-06-2021, Rev. 1.1
Problem Trace the problem Solution
No light
Check the pow er Connect the pow er cord properly and
tu rn o n th e d e vice
Check the w iring
Unplug the m ain. Check connectors on
th e co n n e ctio n s tre e is atta ch e d to a
product or a jum per.
Turn on the pow er
Check the dim m ing
Unplug the m ain. Unplug the dim m er
syste m fro m th e d rive r.
Turn on the pow er
Light output has
dim inished
Check if the light has
been dim m ed via a
dim m er?
In c r e a s e b r ig h t n e s s t o t h e n o rm a l le v e l
Check the operating
conditions of the
lig h t e n g in e
If t h e lig h t e n g in e h a s b e e n r u n n in g a t
elevated tem peratures for an extend-
ed tim e, a decrease in the output w ill
be observed
User m anual
ite m n r : 1 2 0 7 0 1 1 0 , 1 2 0 7 0 1 2 0
XPO X-LED vertical

Product overview /unboxing
In s t a lla t io n in s t r u c t io n s
Follow the installation instructions to ensure
· Safe operation
· Full functionality
· Stated expected lifetim e
· Uninterrupted illum ination
(1 ) XPO X-LED Vertical
(2 ) User m anual
Application notes
The light generator is an electronic device and m ust be handled accordingly. The
different com ponents w ill have different factors influencing the practical lifetim e.
The m ost im portant factor for this system is the condition of the surrounding air
(te m p e ra tu re a n d c le a n lin e ss). T h e d a ta w e h a v e sta te d a b o u t o r a n d th e e x p e c te d
life t im e o f th e k e y c o m p o n e n ts , a re a t t h e te m p e ra tu re s th a t th e su p p lie rs h a v e
perform ed during their standardized tests in clean environm ents.
The light generator is designed to run at m ax am bient tem perature, but the longest
usable operation is achieved w ith low er tem peratures.
Although there is therm al protection built into this device, it is only a safety device
and should not be used as a m easurem ent device to test if the light generator is
ru n n in g a t a to le ra b le su rro u n d in g te m p e ra tu re .
The polyconnector is the m ost stressed part of this system .
Care should be taken to ensure that the fibre ends are 100% clean and free from
dust and grease (fingerprint w ill do dam age.). See w w w .rob-lig h t.c o m fo r re c o m -
mendations to clean fibre ends.
Running the light generator at too high tem peratures w ill not only risk dam age to
th e ligh t so u rce b u t a lso to th e fib re h a rn e ss.
CLEAN AIR
KEEP COOL

Part nam e Description It e m n o .
Parallel splitter 2 x TE AM P 1108 0022
Parallel splitter 4 x TE AM P 1108 0024
Wire Harness Wire harness for XPO X-LED
Extension 3m 8000 0636
Driver 15W For XPO X-LED up to 2m 1148 0022
Driver For XPO X-LED from 2-
Cover 2m
XPO X-LED 53 transm ission
XPO X-LED 80 transm ission
XPO X-LED 93 transm ission
4200 0013
4200 0015
4200 0016
The effectiveness of the active cooling device is greatly dim inished if the cooling
fin s a n d th e a ir in ta k e is b lo c k e d o r p o llu te d w ith d u st. T h is w ill re d u ce th e e x -
pected lifetim e of the product.
The dust m ust be rem oved on a regular basis. Interval depending on the environ-
ment.
A fine brush, vacuum cleaning or light com pressed air can be used for the cleaning.
This light source is not supposed to be otherw ise serviced, if used as recom m ended.
The fan can be replaced using standard tools. A replacem ent kit w ith guide is avail-
able.
If t h e p ro d u c t is n o t p e rfo rm in g a s s p e c ifie d , u se t h e t ro u b le sh o o t in g g u id e . If y o u
need further assistance, please contact RobLight.
Maintenance, spare parts and repairs
Accessories / Spare part
General
Material Alum inium
Dim ensions (L x H x W ) Ø26 x Various
Dist. betw een driver and LED 1.8 m standard, other lengths on request
Weight (total) Depends on length
Safety CE, RoHS, W EEE
Topology Parallel connection
Environm ental
Protection rating IP 2 0
Cooling Natural convection
Am bient tem perature 40°C M ax
Driver/electrical
Driver LED driver constant voltage
Driver size (L x H x W ) 130 x 21 x 68 m m
Supply voltage (m ains) 100–240V 50-60 Hz
Driver expected lifetim e >50000h
Dim m er system s applicable 1-10V, PU SH (m ains)
Fixture voltage 24 V DC
Total pow er consum ption 15 W
Light source
Applied LED Xicato
LED expected lifetim e >50000h @ Ta=25°C
Typical CCT 3000K, other CCT on request
Typical Ra (CRI
1-8
) 98
Technical data

In s ta lla t io n in s t r u c t io n s
Ø33 mm
Connect driver and
main power (100-
240V)
Cover change
Remove the end piece and the small screw, pull out the glass.
Customize the new glass, from the old.
Cut the back of the glass
and break it with your
fingers.
Re-assemble the light
source with the new
glass .