Robustel GoRugged R2000 Operator's manual

Robustel GoRugged R2000 Quick Guide
RT_QG_R2000 Installation and Configuration_v.2.0.2 18.11.2016 1/17
Installation and Configuration
Quick Guide
R2000--Industrial Cellular VPN Router
This document is written for the user which in order to let the user more easily install the router and also know the
way to configure the router. This guide provides step-by-step instruction on how to setup the connection between
R2000 router and PC and how to enter the router configuration mode.
Package Checklist
Before installing theR2000 router, verify that the package contains the following items:
Robustel R2000 Router
Terminal Block for Power
Document and Software CD
Optional Accessories
AC/DC Power Supply Adapter
35mm Din-Rail mounting kit or Wall mounting kit
SMA cellular antenna (HSPA+/LTE)
RP-SMA Wi-Fi antenna (stubby or magnet)
Notify your sales representative if any of the above items is missing or damaged.
Preparation before testing
1xR2000 Router, 1xPC, 1xSIM card, 1xEhternet cable, 2xSMA antenna, 1xpower supplies with terminal block,
(1x35mm Din-Rail mounting kit or Wall mounting kit, 4xM3 screw, 2xM3 screw with point-end)

Robustel GoRugged R2000 Quick Guide
RT_QG_R2000 Installation and Configuration_v.2.0.2 18.11.2016 2/17
Environment Requirements
Power Input:
9 to 26V DC (A014401, A014402, A014403, A014404, A014405, A014406, A014701, A014702, A014703, A014704, A014705,
A014706);
9 to 36V DC
Power Consumption: Idle: 100 mA @ 12 V,
Data Link: 500 mA (peak) @ 12 V
Operating Temperature -20 to +65°C
Operating Humidity 5 to 95% RH

Robustel GoRugged R2000 Quick Guide
RT_QG_R2000 Installation and Configuration_v.2.0.2 18.11.2016 3/17
Chapter 1 Interface Introduction
1.1 Overview
As shown in the following figures, R2000 router has two Ethernet ports (2xLAN or 1xLAN+1xWAN) and two cellular
SIM card slots.
1.2 LED Indicators
Name
Color
Status
Function
RUN
Green
Blinking
Router is ready.
On
Router is starting.
Off
Router is power off.
PPP
Green
Blinking
PPP Indicator: Null
On
PPP Indicator: PPP connection is up.
Off
PPP Indicator: PPP connection is down.
USR
Green
Blinking
SIM: using backup SIM card.
NET: register to a low level network.
Off after blinking
SIM: working fine.
NET: working fine.
Light up
OpenVPN: OpenVPN is connected.

Robustel GoRugged R2000 Quick Guide
RT_QG_R2000 Installation and Configuration_v.2.0.2 18.11.2016 4/17
1.3 Reset Button
1.4 Ethernet port
There are two Ethernet ports in R2000 router, ETH1 is the LAN interface and ETH0 can be the LAN or WAN
interface. Each Ethernet port has two LED indicators. The yellow one is Link indicator and the green one
doesn’t mean anything. There are three status of Link indicator. Please refer to the form below.
Indicator
Status
Description
Link Indicator
Off
Connection is down.
On
Connection is up.
Blink
Data is being transmitted
IPSec: IPSec is connected.
GRE: GRE is connected.
Off after lighting up
OpenVPN: OpenVPN is disconnected.
IPSec: IPSec is disconnected.
GRE: GRE is disconnected.
Green
On
Signal level: 21-31 (Perfect signal level).
Yellow
On
Signal level: 11-20 (Average signal level).
Red
On
Signal level: 1-10 (Exceptional signal level).
When the network is disconnected, those three signal LEDs are designed as a binary combination code to
indicate a series of error report.
(Green Yellow Red) On: 1 Off: 0
001 AT command failed
010 no SIM card detected
011 it need to enter the PIN code
100 it need to enter the PUK code
101 registration failed
110 something wrong happened in the module
Function
Operation
Reboot
Push the button for 2~7 seconds under working status.
Restore to factory
default setting
Keep pushing the button once you power on the
router until all the LED light blink one by one
recurrently. It will cost several seconds to finish the
reset operation.
When all the LED light blinks hold on 2 seconds, it
means that the router loads default successfully.

Robustel GoRugged R2000 Quick Guide
RT_QG_R2000 Installation and Configuration_v.2.0.2 18.11.2016 5/17
Chapter 2 Hardware Installation
2.1 Install SIM Card
Remove slot cover
1. Make sure power supply is disconnected.
2. Use a screwdriver to unscrew the screw on the cover, and then remove the cover, you could find the SIM Card
slots.
Inserting SIM Card
3. Insert the SIM card, and you need press the card with your fingers until you hear “a cracking sound”. Then use a
screwdriver to screw the cover.
Removing SIM Card
4. Make sure router is power off.
5. Press the card until you hear “a cracking sound”, when the card will pop up to be pulled out.
Note:
1. Recommended torque for inserting is 0.5N.m and the maximum torque is 0.7N.m.
2. Please use the specific M2M SIM card when the device works in extreme temperature (temperature exceeding
0-40 ℃ ), because the long-time working of regular SIM card in harsh environment (temperature exceeding
0-40 ℃ )may increase the possibility of SIM card failure.
3. Don’t forget screw the cover for again-theft.
4. Don’t touch the metal surface of the SIM card in case information in the card is lost or destroyed.
5. Don’t bend or scratch your SIM card. Keep the card away from electricity and magnetism.
6. Make sure router is power off before inserting or removing your SIM card.
2.2 Connect the External Antenna
Connect router with an external antenna connector. Make sure the antenna is within correct frequency range and is
screwed tightly. Recommended torque for mounting is 0.35N.m
2.3 Ground the Router
Grounding and wire router helps limit the effects of noise due to electromagnetic interference (EMI). Run the ground
connection from the ground by screwing to the grounding surface before connecting devices.
Note: This product is intended to be mounted to a well-grounded mounting surface, such as a metal panel.

Robustel GoRugged R2000 Quick Guide
RT_QG_R2000 Installation and Configuration_v.2.0.2 18.11.2016 6/17
2.4 Mount the Router
The router may be placed on a horizontal surface such as a desktop, mounted on a DIN-rail, or mounted on the wall.
Two ways of mounting the router
1. Use 4 pcs of M2.5 countersunk head cross recess screws to fix the router on the two metal plates.
And then use 2 pcs of M3 screw with point-end to mount the router with two metal plates on the wall.
Recommended torque for mounting is 0.5N.m and the maximum torque is 0.7N.m.
2. Mount the router on a DIN rail with 3 pcs of M3 countersunk head cross recess screws, and then hang the
DIN-Rail on the holder.
You need to choose a standard holder. Recommended torque for mounting is 1.0N.m and the maximum torque
is 1.2N.m.
Note: When mounting the unit on a DIN-rail, make sure that it is oriented with the metal springs on top.
2.5 Power Supply
R2000 router supports reverse polarity protection, but always refers to the figure above to connect the power
adapter correctly. There are two cables associated with the power adapter. Following to the color of the head,
connect the cable marked red to the positive pole through a terminal block, and connect the yellow one to the
negative in the same way.
Note: The range of power voltage is 9 to 26V DC (A014401, A014402, A014403, A014404, A014405, A014406, A014701, A014702,
A014703, A014704, A014705, A014706) or 9 to 36V DC.

Robustel GoRugged R2000 Quick Guide
RT_QG_R2000 Installation and Configuration_v.2.0.2 18.11.2016 7/17
2.6 Connect R2000 to PC with Ethernet cable
Use a standard cross-over Ethernet cable to connect R2000 to PC with Eth0 or Eth1 port.

Robustel GoRugged R2000 Quick Guide
RT_QG_R2000 Installation and Configuration_v.2.0.2 18.11.2016 8/17
2.7 PD Connection (Optional)
If you want to power on R2000 by Ethernet, please refer to the following topology and connect R2000 to PSE (Power
Sourcing Equipment).
POE power input voltage range is 48~57 VDC.

Robustel GoRugged R2000 Quick Guide
RT_QG_R2000 Installation and Configuration_v.2.0.2 18.11.2016 9/17
Chapter 3 Initial Configuration
The router can be configured through your web browser that include IE 8.0 or above, Chrome and Firefox. A web
browser is included as a standard application in the following operating systems: Linux, Mac OS, Windows
98/NT/2000/XP/Me/Vista/7/8, etc. It provides an easy and user-friendly interface for configuration.
There are various ways to connect the router, either through an external repeater/hub or connect directly to your PC.
However, make sure that your PC has an Ethernet interface properly installed prior to connecting the router.
You must configure your PC to obtain an IP address through a DHCP server or a fixed IP address that must be in the
same subnet as the router. If you encounter any problems accessing the router web interface it is advisable to
uninstall your firewall program on your PC, as this tends to cause problems accessing the IP address of the router.
3.1 Configuring PC in Windows 7
There are two methods to obtain IP address for the PC, one is automatically obtain IP address from DHCP server, and
another is manually configured static IP address within the same subnet of R2000 router.
The configuration for windows system is similar.
1. Go to Start \Control Panel \Network and Internet\Network Connections. Double-click Local Area Connection.

Robustel GoRugged R2000 Quick Guide
RT_QG_R2000 Installation and Configuration_v.2.0.2 18.11.2016 10/17
2. In the Local Area Connection Status window, click Properties.
3. Select Internet Protocol (TCP/IP) and click Properties.