Roca IN-WASH INSPIRA User manual

IN-WASH® INSPIRA SMART TOILET
CLOSE COUPLED BACK TO WALL (4*)
INSTALLATION INSTRUCTIONS
2
- Before installation, read this installation manual thoroughly and the included safety precautions.
Parts must be installed according to the instructions.
- Rain water or grey water is not suitable to operate this equipment. The In-Wash® shower toilet
may only be operated with normal drinking water.
- Do not damage electrical connection components.
- The recommended water supply pressure is 150 kPa to 500 kPa max. Operate equipment within
the recommended water pressure.
- Water supply temperature must be between 10 - 30ºC. Ensure the correct water temperature is
maintained.
- Do not use a water supply hose other than the one provided with this product.
- Make sure that this product is correctly earthed to ground. (If the product is not earth-connected,
there is a risk of electric shock).
-Dual check valve must be fitted before the cistern stop.
Please note that this product has an Integral High Hazard Backflow Prevention device
which complies with the requirements of AS 2845.2 and AS/NZS 3500.1, clause 12.2.3 '
Technical information
Power Supply 240V / 50Hz.
Power Wattage 1700 W
IP Rating IP X4
Note: Any electrical work connected on this project must be installed
by qualified personnel, in accordance with AS/NZS 3000 Wiring Rules.
Certification
Watermark AS1172.1/AS1172.2 Certificate No. WMKA0232
WELS 4 Star, 4.5/3 litre, Average Flush 3.3 litre
RCM
Plumbers, please ensure a copy of the installation
instructions is left with the end user for future reference
page 1 of 18
Plumbers, please ensure a copy of the installation
instructions is left with the end user for future reference
Version 1, October 2018

IN-WASH® INSPIRA SMART TOILET
CLOSE COUPLED BACK TO WALL (4*)
INSTALLATION INSTRUCTIONS
3
400 445
480
790
380
55
680 390
Alternative drainage connections
Included
Min. 125
Max. 225 225
180
[mm]
page 2 of 18

IN-WASH® INSPIRA SMART TOILET
CLOSE COUPLED BACK TO WALL (4*)
4
X2
X1
X1
X2 X2
X2 X2
X1 X1
X1 X1
X1 X1
X2 X2
X2
X1 X1 X1
X2
X2
S
M
L
B
3/8” M - 1/2” H
1/2” H - 3/4” H C
1/2” H - 3/8” H A
X2 X2 X2 X1 X1X1
X1
page 3 of 18

IN-WASH® INSPIRA SMART TOILET
CLOSE COUPLED BACK TO WALL (4*)
5
Pipes
1
Electrical
2
200
Option 2a
Ø1/2”
150 - 500 kPa
Option 1a Option 1b
Option 2b
300
200
Ø1/2”
300
55
125
55
125
3 x 1mm2
L = 300 mm
ØMin: 6 mm
ØMax: 8,5 mm
[mm]
Do not use rain water.
Use only potable water.
page 4 of 18

IN-WASH® INSPIRA SMART TOILET
CLOSE COUPLED BACK TO WALL (4*)
6
C
B
240 VAC
50 Hz.
1700 W Max.
D
OFF
25A lDn 0.03A 10 ó 15A
A
3 x 1mm2
L Min. = 300 mm
ØMin: 6 mm
ØMax: 8,5 mm
According to current legislation
Mandatory
A
The electrical installation must be protected by means of a IDn 0,03A and 25A differential switch and a
magnetothermal switch of 10 or 15A. Both switches must be placed outside the bathroom.
B
A fixed power connection must be connected by a dedicated flexible power cable consisting of 3 wires (active,
neutral, earth) of at least 1mm
2
. The connection must be done inside an IPX4 or better junction box. If it is
necessary to replace the power cable, this must be done by qualified service staff.
C
240V, 50Hz.
Note
- Any electrical work conducted on this product must be installed only by qualified personnel, in
accordance with AS/NZS 3000 Wiring Rules.
-Please consult with a qualified electrician to confirm an appropriate installation location.
-No additional electrical equipment should be fitted inside the WC
-This product (IPX4) shall not be exposed to water jets for cleaning purposes.
page 5 of 18

IN-WASH® INSPIRA SMART TOILET
CLOSE COUPLED BACK TO WALL (4*)
8
2
1
3
Min. 45
1
Ø12
45
90
10
~250
~360
2
1
page 6 of 18

IN-WASH® INSPIRA SMART TOILET
CLOSE COUPLED BACK TO WALL (4*)
9
Water filter
support
Install the water filter on the most accessible side
3
4
a
b
page 7 of 18

IN-WASH® INSPIRA SMART TOILET
CLOSE COUPLED BACK TO WALL (4*)
10
B
1/2” F- 3/4” F
L = 515
C
3/8” F- 1/2” F
L = 560
A
External connection
3/8” M - 1/2” F
L = 610
B
3/8” M - 1/2” F
1/2” F - 3/4” FC
1/2” F - 3/8” FA
1
2
3
5
6
page 8 of 18

IN-WASH® INSPIRA SMART TOILET
CLOSE COUPLED BACK TO WALL (4*)
2
3
1
OFF
1a
2b
I
1
2
3
Earth Active
OFF
7
8
page 9 of 18
Note: Dual check valve must be fitted before cistern stop

IN-WASH® INSPIRA SMART TOILET
CLOSE COUPLED BACK TO WALL (4*)
Internal connection
A
BC
B
3/8” M - 1/2” F
1/2” F - 3/4” FC
1/2” F- 3/8” FA
9
10
page 10 of 18
Note: Dual check valve must be fitted before cistern stop
Note: Dual check valve must be fitted before cistern stop

IN-WASH® INSPIRA SMART TOILET
CLOSE COUPLED BACK TO WALL (4*)
13
1
x2
2
24
B
3
17
1
12
11
page 11 of 18

IN-WASH® INSPIRA SMART TOILET
CLOSE COUPLED BACK TO WALL (4*)
14
1
1
2
Gray
4.5L
Blue
3L
1 3
2
13
14
3
205
mm
page 12 of 18

IN-WASH® INSPIRA SMART TOILET
CLOSE COUPLED BACK TO WALL (4*)
15
1
C
2
3
45
1
1
2
3
2
3
15
16
page 13 of 18
Note: Dual check valve must be fitted before cistern stop

IN-WASH® INSPIRA SMART TOILET
CLOSE COUPLED BACK TO WALL (4*)
16
1
2
3
3
2
1
17
page 14 of 18

IN-WASH® INSPIRA SMART TOILET
CLOSE COUPLED BACK TO WALL (4*)
17
3
4
6
2
1
3
5
18
19
page 15 of 18

IN-WASH® INSPIRA SMART TOILET
CLOSE COUPLED BACK TO WALL (4*)
18
3
2
1
==
20
21
page 16 of 18

IN-WASH® INSPIRA SMART TOILET
CLOSE COUPLED BACK TO WALL (4*)
19
Optional
Included
CR 2032 (x2)
X
X = 2mm
A
X = 3mm
B
X = 4mm
C
Max. 1mm
22
23
page 17 of 18

IN-WASH® INSPIRA SMART TOILET
CLOSE COUPLED BACK TO WALL (4*)
A392111320a
[e-mail]
[e-mail]
Roca Sanitario, S.A.
Avda. Diagonal, 513
08029 Barcelona
SPAIN
www.roca.com
See user manual
ON
21
120 s.
OPEN POWER 3CONNECT 4AUTO-TEST
5 s.
After connecting the power , you have 60 seconds to link the remote control.
To link the remote control , press simultaneously the Drying and Stop buttons on the remote control for 5 seconds.
A beep will be heard and all the LEDs on the remote light up, as a signal that it is connected.
A self-calibration process starts for 120 seconds during which water flows from the e-bidet nozzle window.
2
3
4
Max. 60 s.
24
25
page 18 of 18
Plumbers, please ensure a copy of the installation
instructions is left with the end user for future reference