Roca MULTICLEAN A804001 Series User manual

EN
ES
DE
FR
IT
PT
MULTICLEAN
A804001... A804002... A804004...
001 EU UK002

English
2
Important safeguards
When using electrical products, especially when children are present, basic safety precautions should always be followed, inclu-
ding the following:
Please read this manual carefully before product installation and use.
DANGER- For reducing the possibility of electric shock
1. Do not place or store the remote control at where it can fall or be pulled into the bathtub, sink or tank.
2. Do not place the remote control into the water or other liquid.
3. Do not splash this product with water.
WARNING- To reduce the risk of burn, electrocution, fire or injury
1. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by
a person responsible for their safety.
2. Children should be supervised to ensure that they do not play with the appliance.
3. Use this product only for its intended use as described in this manual.
4. Do not operate the product with damaged cord or plug, or after the product malfunctions, or has been damaged in any way,
or dropped into water. Return the product to the nearest authorized service center for examination, repair, or adjustment.
5. Keep the power cord away from heated surface.
6. Never use this product while sleeping or drowsy.
7. Never drop or insert any object into any opening of product or hose.
8. Do not use this product outdoors.
9. Through poor conditions of the electrical MAINS, shortly voltage drops can appear when starting the equipment.
This can influence other equipment (e.g. blinking of a lamp).
If the MAINS-IMPEDANCE Zmax < 0.3 OHM, such disturbances are not expected.
(In case of need, you may contact your local supply authority for further information).
10. Save these instructions.
Grounding instructions
1. The plug must be plugged into an outlet that is properly installed grounded.
2. In the event of an electrical short circuit, grounding reduces the risk of electric shock.
3. The electrical outlet, which must be a 220-240V~, 50/60Hz, and at least a 15Amp grounded outlet, should be located on the
wall within reach of the unit’s power cord.
4. A Ground Fault Interrupter residual current device (RCD) should be installed on the circuit supplying power to the unit.
DANGER- Improper use of the grounding plug can result in a risk of electric shock.
If repair or replacement the cord or plug is necessary, do not connect the grounding wire to either flat blade terminal.
Check with a qualified electrician or serviceman if the grounding instructions are not completely understood, or if in doubt as to
whether the product is properly grounded.
If it is necessary to use an extension cord, make sure the extension is grounded.
The WC must be installed in the protection volume 3 of the bathroom.
Neither component or connection of the WC must be installed out of this volume.
No electrical device must be introduced inside the WC.
This product must be installed by qualified personnel, in according with the national current regulation.
220V-240V~,
50/60Hz
1300W
600
Volume 1
Volume 0
Volume 2
Volume 3
2400
2250

English
3
For your safety, be sure to obey the followings:
Please read this manual before use and keep this manual at where you can refer easily.
Neglect or misuse followings might lead to the injury or serious damage.
WARNING : “It might cause serious damage or death.”
Please install plug properly. Plug should be connected
with socket firmly, there should not have loosen or plug
imcompletely between plug and socket. Otherwise, the heat
of plug might cause fire. While this product will not be used
for a long time , please unplug it.
Please do not use multiple socket outlets.
Please do not install other power cord or use extension
cord while use which might lead to the danger of fire or
electrocution.
Please do not use harsh brushes or abrasive detergents to
clean the product.
Please do not use plug while your hands are wet which might
lead to the danger of electrocution.
Only use domestic water connected to cold water. Please do not disassembly without professional authorized
technician.
Please do not trample on this product.
Do not press heavily lid or seat.
Please do not bend or press hose and power cord.
This will affect water supply and cause unstable flush function.
Please do not break, process, bend, pull, twist, or place heavy
things on the power cord.
Please avoid using water to wash this product. Please do not place inflammable object or cigarette on this
product.
Please clean the dust on the socket and never use power cord and socket if it has already been broken or loosen.
If there’s dust amassed on the socket or the socket is damaged or loosen which might cause humidity and lead to fire.
Please be sure to unplug the power cord while moving this product.
If the power cord does not unplug while moving this product, this will cause power cord broken and lead to the danger of fire and
electrocution with product damage.

English
4
Parts list
Specification
User’s manual Installation guide Guarantee card Mounting plate with
hardware kits T-valve with bidet hose
Power source 220-240V~, 50/60Hz
Maximum power consumption 1300W
Tap water pressure (connect to cold water) 0.1~0.7 MPa (1~7bar)
Rear spray volume 0.2~0.8 L/min
Front spray volume 0.2~0.8 L/min
Maximum heater capacity 1200W
Heating system Instant water heating
Water temperature Off / 35°C / 37 °C / 39°C
Safety device Thermal fuse
Warm dryer temperature 45°C / 52°C / 60 °C
Maximum heater capacity 350W
Air dryer speed 12 m/s
Safety device Thermal fuse
Length of power cord 120cm
Product weight 3.7kg (±0.3kg)
Above specifications has been measured under room temperature of 25°C, incoming water temperature between 15°C and
30°C and Water pressure of 0.2MPa. Incoming water temperature out of this range can cause unstable temperature of the water
coming out through the nozzle.
Themanufacturer reserves the rightto change above specifications at any time without notice and without incurring
obligations.
Rear & front cleansingDryer

English
5
Lid
Body housing
Nozzle
Seat
*Toilet bowl
Bidet Hose
Side control
Water Shut off Valve*
T-Valve
* Items not supplied with the product.
Front cleaning
Dryer
Oscillating cleaning
Power
Pulsating cleaning
Water/dryer temperature adjustment
Water pressure adjustment Nozzle front and back
position adjustment
Stop function
Rear cleaning
Power outlet *
Power plug
Parts description
Side control

English
6
Clean function
Please occupy the toilet seat in order to activated the sensor installed onto the seat.
Rear cleaning
Front cleaning
Rear and front cleaning setting adjustment
While rear or front clean function activated below parameter can be adjusted: nozzle postition, water temperature, water pressure,
cleaning massage.
Water temperature
Nozzle position
Note: Both rear and front cleaning function can’t working at the same time.
Cleaning function will stop automatically in 5 min. Please press again to resume the function.
1. Cleaning
Press rear cleaning button to activate.
1. Cleaning
Press front cleaning button to activate.
Water temperature adjustment
Press temperature button repeatedly to adjust water
temperature. There are 4 temperature levels.
2. Stop cleaning
Press stop button.
2. Stop cleaning
Press stop button.
Off Low Medium High
Nozzle position adjustment
Press or button to adjust the stretching length of nozzle. There 5-level adjustment.

English
7
Low Medium High
Water pressure
Cleaning massage
Dryer
Please occupy the toilet seat in order to activated the sensor installed onto the seat.
Note:
Do not insert finger or any objects into the fan.
Dryer function will stop automatically in 5min. Please press the button again to resume the function.
Water volume adjustment
Press or button for adjusting the water pressure.
5-level adjustment:1 2 3 4 5
Oscillating cleaning
Press to activate or deactivate oscillating cleaning mode.
With activating the oscillating cleaning function, the nozzle will be moved back and front for widening the
cleaning range.
Pulsating cleaning
Press to activate or deactivate pulsating cleaning mode.
With activating the pulsating cleaning function, the water pressure cycles between strong and soft in a certain
rhythm for cleaning.
2. Temperature adjustment
Press temperature button to adjust temperature until desired
setting. There are 3 temperature levels.
1. Dryer
Press dryer button to activate.
3. Stop dryer
Stop the dryer.
Silent mode
Silent mode
Press and hold temperature button for over 3 seconds to enable beeping sound.
Repeat to return silent mode.

English
8
1. Turn tap water shutoff valve off
completely.
2. Flush the toilet to empty the water tank
Note: Failure to do so could result in
leaking or flooding.
3. Unscrew the filter from the T-Valve.
(the end not connected to a hose)
4. Gently brush and clean the filter with
water to remove the clog.
5. Reconnect the filter to the T-Valve
properly.
Note: Failure to do so could result in
leaking or flooding.
6. Turn the tap water shutoff valve back
on.
Cleaning & maintenance
Nozzle extension
Press pulsating button for 3 seconds, nozzle reaches out automatically which will be remained for 1 minute.
Warning!
1. Do not use aggressive product to clean. Only use neutral product for cleaning.
2. Do not pull or push the nozzle manually.
3. It is forbidden to take out nozzle by hand directly.
Nozzle cleaning
Press oscillating button for 3 sec to activate that nozzle would automatically oscillated back and front during 1 minute. To stop this
function in advance, please press stop button.
Filter cleaning

English
9
1.
Press and hold button for 3 seconds
to shut off the product.
2.
Unplug the power cord from the wall
outlet.
3. Shut off the water supply.
Disconnect the t-valve and bidet hose.
4. Push the release button located on the
back right of the seat and slide out main
unit from mounting plate.
5. Unscrew the drain lever using a coin
to open cover.
Note: When the water tank still has water
in it, do not flip, or skew the product.
6. Drain water from reservoir.
a
b
Cleaning and removal
Use a soft and damp cloth or sponge to wipe off the body gently.
Disconnect the power
1. Unplug the product prior to clean.
2. Push the release button located on the back right of the seat and slide out main unit from mounting plate.
Warning!
1. Do not scrub or use harsh or abrasive chemical cleansers to clean the product. Only use neutral product for cleaning.
2. For a thorough cleaning, you may need to detach the product.
3. Do not damage bidet hose, power cord, ground wire during the removal.
Precautions
1. Do not force any of the parts of the product.
2. In case of storm, disconnect the product from the power supply.
3. In case of house water pipe maintenance, please disconnect the water hose till all pipes get clean.
Note:
Protect the product to get hit or scratch. Uninstall mounting plate and screws and keep them together with the product.
Complete detachment
If you plan not use the product for a long period, please remove the product from the toilet.

English
10
Troubleshooting
Issue Possible Solution
No working
1. Disconnected/ no power supply
2. No electrical power supply
3. Product is power off
1. Connect the product to main power supply
2. Check there’s a 220-240V~,50/60Hz signal with
another product (such us hairdryer)
3. Push the power button (on/off side control)
Low water flow or pressure
1. Clogged filter
2. Twisted hose
3. Nozzle cap is stuck
1. Clean water filter (page 8)
2. Straighten the hose
3. Clean nozzle cap (page 8)
Washing feature does not work
or fails to spray User not properly seated Adjust your sitting position
Product shuts off during use 1. Washing time exceeded 5 minutes
2. Power failure
1. Repeat Cleaning function
2. Check power or unplug the power cord to reset
Water not heated Water temperature set to off Reset heated water temperature (page 6)
Dryer not working Dryer only operates when seat
activated Sit on product to operate dryer