Roca IN-WASH INSPIRA User manual

IN-WASH® INSPIRA HS
SMART TOILET FS
80307300R

2
- Before installation, read this installation manual thoroughly and the included safety precautions.
Parts must be installed according to the instructions.
- Rain water or grey water is not suitable to operate this equipment. The In-Wash shower toilet may
only be operated with normal drinking water.
- Do not damage electrical connection components.
- The recommended water supply pressure is 150 KPa to 500 KPa. Operate equipment within the
recommended water pressure.
- Water supply temperature must be between 10 - 30ºC. Ensure the correct water temperature is
maintained.
- Do not use a water supply hose other than the one provided with this product.
- Make sure that this product is correctly earthed to ground. (If the product is not earth-connected,
there is a risk of electric shock).
- Please note that this product has an Integral High Hazard Backflow Prevention device that
meets the requirements outlined in AS/NZS 3500.
Technical information
Power Supply 240V / 50Hz.
Power Wattage 1700 W
IP Rating IPX 4
Note: Any electrical work connected on this project must be installed
by qualified personnel, in accordance with AS/NZS 3000 Wiring Rules.
Certification
Watermark AS1172.1/AS1172.2 Certificate No. WMKA02321
WELS 4 Star, 4.5/3 litre, Average Flush 3.3 litre
RCM

3
405 450
485
385
40
585
385
Alternative drainage connections
Included
Min. 125
Max. 225
960
180
355
[mm]

4
X1 X1
X2 X2 X2 X1 X1
1/2” H - 3/4” H
X1
X2
X2 X2 X2 X1 X1
X1
X2
X2
S
M
L

5
200
Ø1/2”
500 kPa
Option 1a Option 1b
300
200
Ø1/2”
300
Do not use rain water.
Use only potable water.
Electrical
2
Pipes
1
Option 2a Option 2b
55
125
55
125
3 x 1mm2
L = 300 mm
ØMin: 6 mm
ØMax: 8,5 mm

6
240 VAC
50 Hz.
1700 W Max.
D
OFF
25A lDn 0.03A 10 ó 15A
A
According to current legislation
3 x 1mm2
L Min. = 300 mm
ØMin: 6 mm
ØMax: 8,5 mm
Mandatory
C
B
AThe electrical installation must be protected by means of a IDn 0,03A and 25A differential switch and a
magnetothermal switch of 10 or 15A. Both switches must be placed outside the bathroom.
B
A fixed power connection must be connected by a dedicated flexible power cable consisting of 3 wires (active,
neutral, earth) of at least 1mm2. The connection must be done inside an IPX4 or better junction box. If it is
necessary to replace the power cable, this must be done by qualified service staff.
C240V, 50Hz.
Note
- Any electrical work conducted on this product must be installed only by qualified personnel, in
accordance with AS/NZS 3000 Wiring Rules.
- Please consult with a qualified electrician to confirm an appropriate installation location.
- No additional electrical equipment should be fitted inside the toilet.
- This product (IPX4) shall not be exposed to water jets for cleaning purposes.

7
1
2
Min. 45
3
4
Ø12
45
90
10
~200
~360
123
OFF
L Min. = 300 mm
Neutral Ground Phase
3
2
1
a
b
2
1

8
2
3
1
OFF
Option 1a
2a
Included
Internal connection
Note: Dual check valve must be fitted before cistern stop.
123
OFF
L Min. = 300 mm
Neutral Ground Phase
3
2
1
a
b
3
4

9
2
3
1
OFF
Option 1a
2a
Included
Internal connection
Note: Dual check valve must be fitted before cistern stop.
x2
17
5
6

10
1
2
3
45
1
2
3
7
8

11
1
2
3
3
2
1
9

12
3
1
3
2
10
11

13
3
2
1
= =
12
13

14
Optional
Included
CR 2032 (x2)
X
X = 2mm
A
X = 3mm
B
X = 4mm
C
Max. 1mm
14
15

15
See user manual
1
2
ON
ON
21
120 s.
OPEN POWER 3CONNECT 4AUTO-TEST
After connecting the power , you have 60 seconds to link the remote control.
To link the remote control , press the Stop button on the remote control for 5 seconds. A beep will be heard and
all the LEDs on the remote light up, as a signal that it is connected.
A self-calibration process starts for 120 seconds during which water flows from the e-bidet nozzle window.
2
3
4
Max. 60 s.
5 s.
16
17

A8070S310Ra
Roca Sanitario, S.A.
Avda. Diagonal, 513
08029 Barcelona
SPAIN
www.roca.com.au/
See user manual
1
2
ON
18