Roca IN-WASH INSPIRA SMART TOILET WH User manual

IN-WASH® INSPIRA
SMART TOILET WH
A80306000R

2
- Before installation, read this installation manual thoroughly and the included safety precautions.
Parts must be installed according to the instructions.
- Rain water or grey water is not suitable to operate this equipment. The In-Wash shower toilet may
only be operated with normal drinking water.
- Do not damage electrical connection components.
- The recommended water supply pressure is 150 KPa to 500 KPa. Operate equipment within the
recommended water pressure.
- Water supply temperature must be between 10 - 30ºC. Ensure the correct water temperature is
maintained.
- Do not use a water supply hose other than the one provided with this product.
- Make sure that this product is correctly earthed to ground. (If the product is not earth-connected,
there is a risk of electric shock).
- Please note that this product has an Integral High Hazard Backflow Prevention device that
meets the requirements outlined in AS/NZS 3500.
Technical information
Power Supply 240V / 50Hz.
Power Wattage 1700 W
IP Rating IPX 4
Note: Any electrical work connected on this project must be installed
by qualified personnel, in accordance with AS/NZS 3000 Wiring Rules.
Certification
Watermark AS1172.1/AS1172.2 Certificate No. WMKA02321
WELS 4 Star, 4.5/3 litre, Average Flush 3.3 litre
RCM

3
562
400
250250
55
445
480
960
380
31
X2
X2 X2 X2 X1
X1 X1
X1
X1 X1
X1
X1
X2
X2
[mm]
S
M
L

4

5
Recommended Sample installation
LH
55 ÷ 60
Fixation
Recommended installation
90
320
180
[mm]
[mm]
355
220
Ø110
Ø40
55 ÷ 60
Option 1a
2a
A890090800

6
Pipes
1
Electrical
2
75
70
Ø1/2”
Option 2a
75
70
Ø1/2”
500 kPa
55
55
55
55
Option 1a Option 1b
Option 2b
3 x 1mm2
L = 300 mm
ØMin: 6 mm
ØMax: 8,5 mm
[mm]
Do not use rain water.
Use only potable water.

7
OFF
25A lDn 0.03A 10 ó 15A
A
According to current legislation
240 VAC
50 Hz.
1700 W Max.
D
C
B
Mandatory
3 x 1mm2
L Min. = 300 mm
ØMin: 6 mm
ØMax: 8,5 mm
AThe electrical installation must be protected by means of a IDn 0,03A and 25A differential switch and a
magnetothermal switch of 10 or 15A. Both switches must be placed outside the bathroom.
B
A fixed power connection must be connected by a dedicated flexible power cable consisting of 3 wires (active,
neutral, earth) of at least 1mm2. The connection must be done inside an IPX4 or better junction box. If it is
necessary to replace the power cable, this must be done by qualified service staff.
C240V, 50 Hz.
Note
- Any electrical work conducted on this product must be installed only by qualified personnel, in
accordance with AS/NZS 3000 Wiring Rules.
- Please consult with a qualified electrician to confirm an appropriate installation location.
- No additional electrical equipment should be fitted inside the WC.
- This product (IPX4) shall not be exposed to water jets for cleaning purposes.

8
1
2
3
Neutral Earth Active
123
456
d1
d2
(+3mm)
d2
d1
(+3mm)
45º
ss/2
OFF
2
3
Included
1
OFF
12
Not included
1
2

9
2
1
x2
Not included
19
3
2
3
Included
1
OFF
12
Not included
3
4

10
1
1
2
3
23
1
C
2
3
45
5
6

11
1
2
3
3
2
1
7

12
1
3
2
4
6
5
2
1
3
= =
3
1
8
9

13
= =
3
1
X
X = 2mm
S
X = 3mm
M
X = 4mm
L
3
2
1
Max. 1mm
11
10

14
X
X = 2mm
S
X = 3mm
M
X = 4mm
L
3
2
1
Max. 1mm
Optional
Included
CR 2032 (x2)
ON
21
120 s.
OPEN POWER 3CONNECT 4AUTO-TEST
5 s.
After connecting the power , you have 60 seconds to link the remote control.
To link the remote control , press simultaneously the Drying and Stop buttons on the remote control for 5 seconds.
A beep will be heard and all the LEDs on the remote light up, as a signal that it is connected.
A self-calibration process starts for 120 seconds during which water flows from the e-bidet nozzle window.
2
3
4
Max. 60 s.
12
13

15
Optional
Included
CR 2032 (x2)
ON
21
120 s.
OPEN POWER 3CONNECT 4AUTO-TEST
5 s.
After connecting the power , you have 60 seconds to link the remote control.
To link the remote control , press simultaneously the Drying and Stop buttons on the remote control for 5 seconds.
A beep will be heard and all the LEDs on the remote light up, as a signal that it is connected.
A self-calibration process starts for 120 seconds during which water flows from the e-bidet nozzle window.
2
3
4
Max. 60 s.
See user manual
14
15

A392111310h
Roca Sanitario, S.A.
Avda. Diagonal, 513
08029 Barcelona
SPAIN
www.roca.com.au/