Rokonet WisDom User manual

W
Wi is sD Do om m S Si im mp pl le e U Us se er r G Gu ui id de e
RTX0036 – WisDom Simple User Guide
Page 1 of 4
WisDom
Simple User Guide

W
Wi is sD Do om m S Si im mp pl le e U Us se er r G Gu ui id de e
RTX0036 – WisDom Simple User Guide
Page 2 of 4
Congratulations on the purchase of your WisDom wireless domestic security system.
To make the most of your system we advise you to take some time to read through
this simple user guide and also the accompanying user manual.
W
Wi ir re el le es ss s f fo ob b b bu ut tt to on ns s
Note: The buttons on the wireless keyfob are sensitive, so to avoid false alarms,
please handle the fobs with care.
FULL SET
UNSET
PANIC/EMERGENCY
If enabled
PART SET
If enabled
User functions:
1) Omit zone

W
Wi is sD Do om m S Si im mp pl le e U Us se er r G Gu ui id de e
RTX0036 – WisDom Simple User Guide
Page 3 of 4
SETTING
Full Setting
Press [Code Number] then press [ ] and then exit via designated final exit door.
OR
Press the [] button on the Wireless Keyfob and then exit via designated final exit door.
Part/Night Setting
Press [Code Number] then [ ] the system will then set after designated countdown time.
OR
Press the blank [RECESSED] button (If enabled) on the Wireless Keyfob the system will then set after designated
countdown time
UNSETTING
Full Unsetting
Press [Code Number] then [ ]
OR
Press the [ ] button on the Wireless Keyfob
Special Wireless Keyfob function
If enabled, press the small round button to activate a Panic/Medical Emergency condition
CODES
Adding, Changing and Deleting a Code
Press [*] then [5] then [Grand Master Code] then [#] then [1] then [1]
Enter a two digit USER ID number (00 to 32), then press [#]
Note: Grand Master code is always (00) user ID
Enter a Code number for this chosen user and press [#]
Note: A Code of ‘0’ (zero) will delete the existing Code
Press [*] [*] [*] [*] to return to normal display
THE FAULT LED
In the event of a System Fault, the FAULT Led will flash.
The Fault Led will remain flashing until the fault has been acknowledged.
To view and acknowledge the fault, press [#] then [8] then [Grand Master Code] then [#]
The System Fault will be shown.
Press the [ ] button to change ’N’ to ‘Y’ and press [#]
If the fault has been rectified, the Fault Led will no longer flash.
IN THE EVENT OF GREEN POWER LED IS FLASHING
This signifies that mains power has been lost and may now have been restored.
To acknowledge and clear the LED, press [#] then [3] then [Grand Master Code] then [#]
The system will show AC loss.
Press the [ ] button to change ’N’ to ‘Y’ and press [#]
If AC power has been restored the power LED will return to a solid green LED.
ALARM HAS OCCURRED
Unset the system, then press [*]
If the display on the panel shows “call engineer”.
Your system requires a reset by your alarm installer.
Please call telephone number displayed or call your installation company.

W
Wi is sD Do om m S Si im mp pl le e U Us se er r G Gu ui id de e
RTX0036 – WisDom Simple User Guide
Page 4 of 4
Z
ZO ON NE E L LI IS ST TI IN NG G
ZONE NUMBER LOCATION
1
2
3
4
5
6
7
8
9
10
11
12
U
US SE ER R L LI IS ST TI IN NG G
USER ID USER NAME
00 ALWAYS GRAND MASTER
01
02
03
04
05
Note: Please note down any extra users you add.
SITE ID _ _ /_ _ _ _