Roland VersaCAMM ECO-SOL MAX3 User manual

Ink Switching Method
To ensure correct and safe usage with a full understanding of this product's performance, please be sure to read through
this manual completely and store it in a safe location.
Unauthorized copying or transferral, in whole or in part, of this manual is prohibited.
The contents of this operation manual and the specications of this product are subject to change without notice.
The operation manual and the product have been prepared and tested as much as possible. If you nd any misprints or
errors, please inform us.
Roland DG Corp. assumes no responsibility for any direct or indirect loss or damage that may occur through use of this
product, regardless of any failure to perform on the part of this product.
Roland DG Corp. assumes no responsibility for any direct or indirect loss or damage that may occur with respect to any
article made using this product.
About this Manual
This manual explains how to switch the ink being used from ECO-SOL MAX 2 ink (hereinafter called MAX 2 ink) to ECO-SOL
MAX3 ink (hereinafter called MAX 3 ink).*
To prevent the MAX 2 ink and the MAX 3 ink from mixing, perform operations according to the procedures given in this manual.
* Colors with MAX 3 ink are dierent than with MAX 2 ink.
ECO-SOL MAX2 ECO-SOL MAX3

2
ECO-SOL MAX 3 Ink Switching Method
Contents
Contents......................................................................................................................................2
Introduction .................................................................................................................................3
Overall Flow..................................................................................................................................................................................... 3
Preparation before Operations....................................................................................................4
STEP 1: Checking the Package Contents............................................................................................................................... 4
STEP 2: Checking the Necessary Files..................................................................................................................................... 4
STEP 3: Writing a Memo with the VersaWorks Settings ................................................................................................... 4
Switching the Ink .........................................................................................................................5
STEP 1: Updating the Printer Unit Firmware........................................................................................................................ 5
STEP 2: Switching the Ink............................................................................................................................................................ 5
STEP 3:
Cleaning of the Periphery of the Print Heads (Manual Cleaning)....................................................................... 6
STEP 4: Replacing the Wipers and Felt Wipers ..................................................................................................................10
STEP 5: Bidirectional Printing Correction............................................................................................................................13
STEP 6: Updating VersaWorks .................................................................................................................................................13
Important: Changes and Precautions after Switching the Ink ...................................................17
Change: When to Perform Manual Cleaning.....................................................................................................................17
Change: Cleaning Locations During Manual Cleaning..................................................................................................18
Daily Precautions.........................................................................................................................................................................18
When Not in Use for a Prolonged Period, Precaution 1.................................................................................................19
When Not in Use for a Prolonged Period, Precaution 2.................................................................................................19
When Operations Are Interrupted .............................................................................................20
When the Message "STOPPED FOR MOTOR PROTECTION" Is Displayed.................................................................20
When the Cleaning/Wiper Replacement Operation Is Interrupted ..........................................................................20
In this operation manual, excluding the case where "Roland VersaWorks" is shown on the computer screen, "Roland VersaWorks"
is written as "VersaWorks."
Company names and product names are trademarks or registered trademarks of their respective holders.
Copyright © 2015-2016 Roland DG Corporation http://www.rolanddg.com/

3
ECO-SOL MAX 3 Ink Switching Method
Introduction
Overall Flow
Preparation before Operations
STEP 1: Checking the Package Contents (P. 4 )
STEP 2: Checking the Necessary Files (P. 4 )
STEP 3: Writing a Memo with the VersaWorks Settings (P. 4 )
Switching the Ink
STEP 1: Updating the Printer Unit Firmware (P. 5 )
(Required time: Approx. 5 minutes)
STEP 2: Switching the Ink (P. 5 )
(Required time: Approx. 20 to 30 minutes)
STEP 3: Cleaning of the Periphery of the Print Heads (Manual Cleaning; P. 6 )
(Required time: Approx. 10 minutes)
STEP 4: Replacing the Wipers and Felt Wipers (P. 10 )
(Required time: Approx. 10 minutes)
STEP 5: Bidirectional Printing Correction (P. 13 )
(Required time: Approx. 5 minutes)
STEP 6: Updating VersaWorks (P. 13 )
(Required time: Approx. 10 minutes)
Changes and Precautions
Important: Changes and Precautions after Switching the Ink (P. 17 )

4
ECO-SOL MAX 3 Ink Switching Method
Preparation before Operations
STEP 1: Checking the Package Contents
This kit contains the following items. Make sure they are all present and accounted for.
Items used during ink switching
Cleaning sticks Tweezers (1) Gloves (1 set) Wipers (2)
Felt wipers (2) Drain bottles (2) Drain funnel (1)
Items used after ink switching (not used during ink switching)
Cleaning liquid (1)
(dedicated for use with
MAX3 ink)
STEP 2: Checking the Necessary Files
The rmware and updater downloaded from http://www.rolanddg.com/ecosolmax3/ are necessary for the operations in
this manual.
Check that the following les are present.
Firmware: XF640Firm240.exe (in the "Firmware" folder)
Updater: LocalUpdater.exe (Ver. 5.5.0 or later; in the "Roland VersaWorks local updater" folder)
If the above les are not present, download them from the following URL.
http://www.rolanddg.com/ecosolmax3
STEP 3: Writing a Memo with the VersaWorks Settings
Important
As the nal step when you switch the ink, update VersaWorks to a version that supports MAX 3 ink. After the update, because
the printer that has been switched to MAX 3 ink will be connected as a new printer, the previous job data and settings will
be deleted. Write down the IP address and the settings of the connected printer such as "Quality."

5
ECO-SOL MAX 3 Ink Switching Method
Switching the Ink
STEP 1: Updating the Printer Unit Firmware
Use the le that you have downloaded to update the rmware of the printer unit to a version that supports MAX 3 ink. For
the update method, refer to "readme.pdf," the le that you downloaded at the same time as the rmware.
STEP 2: Switching the Ink
1. Display the [CHANGE INK SET] menu.

Press .

Press several times to display the screen shown on the left.
Press .

Press several times to display the screen shown on the left.
Press , then .

Press .

Press or to select [YES].
Press .
2. Switch the ink cartridges.

When the screen on the left is displayed, remove the drain bottle and
discard the discharged uid.
Use the included drain funnel to transfer the discharged uid from the printer's drain
bottle to the included drain bottle.
CAUTION Before you detach the drain bottle, be sure to wait for the screen to display "EMPTY
DRAIN BOTTLE." After discarding the discharged uid, promptly attach the drain bottle
to the machine.
Failing to follow this procedure may cause discharged uid to ow out of the machine and
spill, soiling your hands or the oor.
WARNING Never place discharged uid or ink near an open ame.
Doing so may cause a re.
CAUTION To store discharged uid temporarily, place it in the included drain bottle or in a du-
rable sealed container such as a metal can or polyethylene tank, and cap the container
tightly.
Any spillage or vapor leakage may cause a re, an odor, or physical distress.
Dispose of discharged uid properly, in accordance with the laws in effect in your locale.
Discharged uid contains toxic ingredients. Never attempt to incinerate discharged uid or discard it with ordinary trash.
Also, do not dispose of it in sewer systems, rivers, or streams. Doing so may have an adverse impact on the environment.
/'07
57$/'07
57$/'07
+0-%10641.
+0-%10641.
%*#0)'+0-5'6
%*#0)'+0-5'6!
=;'5?01
'/26;
&4#+0$166.'

Switching the Ink
6
ECO-SOL MAX 3 Ink Switching Method

Install the drain bottle.

Press .

Remove all the currently inserted ink cartridges.

When the screen on the left is displayed, remove the drain bottle and
discard the discharged uid.
Use the included drain funnel to transfer the discharged uid from the printer's drain
bottle to the included drain bottle.

Install the drain bottle.

Press .

Before you insert the new ink cartridge
for each color, gently shake the cartridge.

Set in place new ink cartridges.
When you set in place the new cartridges, the machine starts lling with ink.
When the screen shown in the gure appears, the ink cartridge switching operation
is nished. Proceed to the next procedure.
STEP 3: Cleaning of the Periphery of the Print Heads (Manual Cleaning)
CAUTION Be sure to perform operations as specied by the instructions, and never touch any
area not specied in the instructions.
Failure to observe these instructions may cause the machine to move suddenly, resulting
in injury.
4'/18'51.%46

'/26;
&4#+0$166.'
5'651.%46

(+..+0)+0-
12'0%18'4.
Important notes on this procedure
Before attempting this operation, remove any media.
To prevent the print heads from drying out, nish this procedure in 30 minutes or less. A warning beep sounds after
30 minutes.
Never use any implements other than the included cleaning sticks. Cotton swabs or other lint-producing items may dam-
age the print heads. If you use up the cleaning sticks, purchase new ones from your authorized Roland DG Corp. dealer.
Do not use a previously used cleaning stick. Reusing cleaning sticks may reduce the printing quality.
Do not put a cleaning stick that has been used for cleaning into the cleaning liquid. Doing so will deteriorate the
cleaning liquid.
Never rub the nozzle surface of the print heads.
Stroke the sponges very gently, applying as little pressure as possible. Never rub, scrape, or crush them.

Switching the Ink
7
ECO-SOL MAX 3 Ink Switching Method
1. Prepare for manual cleaning.

Open the left cover.

Remove the cut rail.
Press .

Close the left cover.

Open the left cover.
12'0%18'4.
Click!
4'/18'%76
4#+.
%.15'%18'4.
Click!
12'0%18'4.
If a warning beep sounds during the following operations
If the operations are not completed within 30 minutes from the message "OPEN COVER L" shown above is displayed,
a warning beep will sound to warn you of the print heads drying out. When the warning beep sounds, attach the left
and right covers, close the front cover, and then press . This temporarily interrupts the operations. After you
interrupt the operations, you cannot continue the operations with the procedures in this manual. Refer to the user's
manual of the model that you are using and perform the operations according to the details listed under P. 20 "When
Operations Are Interrupted".

Switching the Ink
8
ECO-SOL MAX 3 Ink Switching Method

Open the right cover.
Preparations are complete when this screen appears.
2. Perform the manual cleaning.

Touch the location shown in the gure to discharge any
static electricity.

Put on the pair of gloves (included).

Moisten the cleaning stick with the cleaning liquid.
12'0%18'44
Click!
/#07#.%.'#0+0)
(+0+5*'&!
Use the cleaning liquid that you have been using since before
switching the ink. Use the cleaning liquid included with the
switching kit only after you have switched the ink.
Be sure to perform cleaning
using one of the included
cleaning sticks.

Switching the Ink
9
ECO-SOL MAX 3 Ink Switching Method

Clean the locations shown in the following gure.
Exercise special care in cleaning o any accumulated ink. You can make the accumulated ink easier to clean o by ap-
plying cleaning liquid to cleaning locations and , and then wiping these locations o with the cleaning stick.
Only moisten the part indicated with diagonal lines in location with cleaning liquid on the cleaning stick.

Press .

Close the left cover.

Close the right cover.
When the screen shown in the gure appears, the cleaning of the periphery of the
print heads (manual cleaning) is nished. Proceed to the next procedure.
%.15'%18'4.
%.15'%18'44
12'0%18'44
Also carefully clean the sides of the print heads.
During this work, be careful not to touch the print head surface (nozzle surface) directly with the
cleaning stick.
Area to clean
Area to moisten

Switching the Ink
10
ECO-SOL MAX 3 Ink Switching Method
STEP 4: Replacing the Wipers and Felt Wipers
CAUTION Be sure to perform operations as specied by the instructions, and never touch any
area not specied in the instructions.
Failure to observe these instructions may cause the machine to move suddenly, resulting
in injury.
1. Replace the wipers.

Open the right cover.
Preparations are complete when this screen appears.

Replace the rst wiper.

Press .

Close the right cover.
If a warning beep sounds during operation
Attach the left and right covers, close the front cover, and then press . After this, you cannot continue
the operations with the procedures in this manual. Refer to the user's manual of the model that you are using
and perform the operations according to the details listed under P. 20 "When Operations Are Interrupted".
12'0%18'44
4'2.#%'9+2'4
(+0+5*'&!
%.15'%18'44
Place the inclined end on the back side.
If the wiper is installed with the incorrect
orientation, appropriate cleaning will not
be possible.
Hook
Disconnect the hooks.
Using the tweezers to press on the hook in the hole on
the wiper makes it easier to remove the wiper.
Pull up and
out.
Hook
Tweezers (included)
Attaching a new wiper
Removing an old wiper
Attach the part to the hooks.
Be sure to attach the part to the
hooks. Failure to do so may result
in dot drop-out or other problems.
If the area is dark and difcult
to see, use a ashlight or a
similar device to illuminate
the area.