Roper Rhodes EMINENCE EM70RAL User manual

Please retain for future reference. Instructions should be kept / passed to end-user once installation is complete.
INSTALLATION & AFTERCARE INSTRUCTIONS
MIRROR PRODUCT INSTRUCTIONS
EMINENCE MIRRORS
ELECTRICAL SAFETY INSTRUCTIONS
All fittings must be installed by a competent person, in accordance with current IEE wiring
regulations. If in doubt consult a qualified electrician
IMPORTANT
Always switch off the electrical supply at the mains during installation and maintenance. It is
recommended that the fuse is withdrawn or the circuit breaker is switched off for the necessary
circuit before installation commences.
The product must be installed with a minimum distance of 150mm between the infrared sensor
and any adjacent wall or obstruction to ensure correct function of the sensor.
Fitting in Bathrooms is subject to the appropriate zone in accordance with IEE Regulations. This
product is suitable for zone 2 and outside zones. IT IS NOT suitable for installation in Zone 0 or
Zone 1. It is also not suitable for installation in saunas, steam rooms or shower cubicles. This
product is only suitable for permanent installation. DO NOT connect to a trailing plug and socket
outlet. Although this product has an Ingress Protection rating of IP44 it is only suitable for indoor
use. Do not attach the product to surfaces that are damp or otherwise electrically conductive.
INSTALLATION CARE & SAFETY
Wear suitable eye protection when drilling. Take care when using power tools near water - the use
of a residual current device (RCD) is advised. Beware of hidden cables or pipes. Take care if
drilling on tiled surfaces in case the drill slips. A piece of masking tape applied to the wall before
marking out the fixing holes will stop the drill from wandering.
DO NOT strike glass components with hard or pointed items. DO NOT place very hot or very cold
items against or in close proximity to glass surfaces unless an adequately thick insulation material
is used to prevent such items coming in contact with the glass.
The nominal thickness of the mirror glass used in this product is 5mm and is film backed for
safety. If the glass becomes chipped or broken replace immediately.
This product should be positioned well away from curtains and other fabrics. Never cover the
mirror. This product is heated, we recommend that it is turned off after use and should never be
left on for prolonged periods of time
This product should only to be installed by a competent person.
CLEANING
It is recommended that the unit is cleaned with a soft, dry, non abrasive cloth when turned off.
Never use cleaning agents or abrasive materials on any type of surface finish. Do not allow
moisture to come into contact with the electrical components.
COMPLIANCE
This product complies with all relevant British
and European safety standards.
22
2
OUTSIDE
ZONES
2
ZONE
1
0.75m
2.25m
3.0m
0.6m 0.6m
0.75m
BATHROOM ZONES DIAGRAM
Distances from a bath tub or shower tray
EM70RAL & EM80RAL
EM55CAL & EM80CAL
EM65OAL
AO.010.18.V3
Strip wires to a suitable
length. DO NOT connect
to a plug & socket outlet.
THIS PRODUCT IS MANUFACTURED TO CLASS I
CATEGORY AND MUST HAVE AN EARTH CONNECTION.
! IF IN DOUBT CONSULT YOUR ELECTRICIAN !
COLOUR CODING:
L - Live = Brown
N - Neutral = Blue
- Earth = Green & Yellow
EM80PAL
EM70RAL, EM55CAL, EM65OAL
EM80RAL, EM80CAL, EM80PAL
-

INSTALLATION PROCEDURE
The wall surface must be of suitable strength and construction.
1)
Measure the distance (X) between the keyhole slots on the back of the mirror.
2) Mark out the fixing screw positions on the wall using a pencil to the desired
height, ensuring they are spaced at distance (X).
3) Drill the marked out positions and fit the wall plugs accordingly. Fix the screw into
position, leaving a small amount of the screw head proud of the wall for hanging.
NOTE: The wall plugs supplied are only suitable for solid stone / brick walls. For
plasterboard walls use specialist wall plugs.
4) The next step is to make the electrical connection from the mirror to the mains
supply. Use the connection wire found at the rear of the mirror to make the
necessary connections in accordance with the current IEE regulations. A second
person will need to hold the mirror in place whilst electrical connections are made.
5)
The mirror should easily slide onto the fixing screws and secure into place.
NOTE: To secure the mirror further, a small amount of silicone sealant can be
applied to the side of the extrusions to prevent the mirror being accidently pulled
away from the wall.
To remove the mirror, the mirror should first be lifted and then pulled away from the
wall.
Mirror for illustrative
purposes. Please
match your
components to the
relevant diagram
1
Roper Rhodes Ltd, Brassmill Lane Trading Estate, Bath, BA1 3JF
Tel:[phone] | Email: [email protected]
www.roperrhodes.co.uk
Turn Mirror ON/OFF
To turn the mirror on/off, slowly wave
your hand in front of the IR sensor.
Change LED colour
1. When the mirror is OFF
2. Hold your hand in front of the IR
sensor to adjust the colour tempera-
ture.
3. Remove hand from IR sensor once
desired colour temperature is
achieved.
warm cool
Change LED intensity
1. When the mirror is ON
2. Hold your hand in front of the IR
sensor to adjust its brightness.
3. Remove hand from IR sensor
once desired intensity is reached.
OPERATING INSTRUCTIONS
The Eminence Mirror comes with LED lighting, which is controlled via an IR sensor
located on the front face of the product. The lighting can be controlled using the
gestures detailed below:
Xmm
Distance
Hold hand
in position
Hold hand
in position
Portrait
Distance X
Back View
3
Mains Supply
Distance X
2
5
Wall Screws
Wall plugs
4
MIRROR PRODUCT INSTRUCTIONS
EMINENCE MIRRORS EM70RAL, EM55CAL, EM65OAL
EM80RAL, EM80CAL, EM80PAL
-