Roper Rhodes MLE420 Parts list manual

Beat Mirror Installation & aftercare instructions
Please retain for future reference
22
2
OUTSIDE
ZONES
2
ZONE
1
0.75m
2.25m
3.0m
0.6m
0.6m
0.75m
Bathroom Zones Diagram
Distances from a bath tub or shower tray
AR.RR.MLE420 | 08.13 V1.00
Roper Rhodes, Brassmill Lane Trading Estate, Bath, BA1 3JF
TEL: [phone] | FAX: [phone]
www.roperrhodes.co.uk
Product code
MLE420
ELECTRICAL SAFETY INSTRUCTIONS
(Applicable to UK Installations only)
All fittings must be installed by a competent person, in accord-
ance with current IEE wiring regulations. If in doubt consult a
qualified electrician
IMPORTANT
Always switch off the electrical supply at the mains during
installation and maintenance. It is recommended that the fuse
is withdrawn or the circuit breaker is switched off for the
necessary circuit before installation commences.
Fitting in Bathrooms is subject to the appropriate zone in
accordance with IEE Regulations. This product is suitable for
zone 2 and outside zones. IT IS NOT suitable for installation in
Zone 0 or Zone 1. It is also not suitable for installation in saunas,
steam rooms or shower cubicles. This product is only suitable
for permanent installation. DO NOT connect to a trailing plug
and socket outlet. Although this product has an Ingress
Protection rating of IP44 it is only suitable for indoor use. Do not
attach the product to surfaces that are damp or otherwise
electrically conductive.
INSTALLATION CARE & SAFETY
Wear suitable eye protection when drilling. Take care when
using power tools near water - the use of a residual current
device (RCD) is advised. Beware of hidden cables or pipes.
Take care if drilling on tiled surfaces in case the drill slips. A
piece of masking tape applied to the wall before marking out the
fixing holes will stop the drill from wandering.
IMPORTANT
DO NOT strike glass components with
hard or pointed items. DO NOT place
very hot or very cold items against or in
close proximity to glass surfaces unless
an adequately thick insulation material is
used to prevent such items coming in
contact with the glass.
The nominal thickness of the mirror glass
used in this product is 5mm and is film
backed for safety. If the glass becomes
chipped or broken replace immediately.
This product should be positioned well
away from curtains and other fabrics.
Never cover the mirror. This product is
heated, we recommend that it is turned
off after use and should never be left on
for prolonged periods of time
This product could be dangerous and is
only to be installed by a competent
person.
“There is no sound from my Beat Mirror.”
- The volume on either device is muted or turned down.
- There is a problem with the Bluetooth
®
connection - try erasing the connection on the audio device and
then re-pairing.
- There may be interference from other nearby Bluetooth
®
enabled devices - try turning them off.
- The connected devices are too far apart and out of range - try moving the devices closer together.
“I cannot pair the mirror with my Bluetooth
®
device.”
- The mirror may not be in pairing mode - to do this press and hold the button for three seconds. The
indicator light will flash and the mirror will beep to confirm pairing mode.
- The Bluetooth
®
capability of your chosen device is turned off or out of range.
- There was a problem during pairing - some devices will pair automatically when selected some will
require a pass code or acceptance of the connection before they will finalise the pairing.
- Refer to your Bluetooth
®
device’s instruction manual to ensure it supports the A2DP (stereo Bluetooth
®
)
profile.
- If attempting to connect to a PC or Mac computer, ensure that your Beat Mirror is set as the audio output
device within the audio settings menu of the device. You may need to play a track to finalise the connec-
tion.
“The sound quality is poor.”
- Your Bluetooth
®
device may be close to being out of range and should be moved closer to the mirror.
- For those devices that support the use of Applications, there may be too many running in the background
which can affect the amount of internal resources available on the device to transmit audio. Closing any
non-essential applications may improve audio quality.
- Similarly, if the selected device has Wi-Fi capabilities, turning this off may improve audio quality.
- There could have been a problem during the initial pairing of devices. Erase the connection using your
Bluetooth
®
device and re-pair.
- For those devices with in-built sound equalisation, adjusting these settings can greatly improve the sound
quality of any audio played through your Beat Mirror.
The Bluetooth
®
word mark and are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by
Roper Rhodes is under license. Other trademarks and trade names are those of their respective owners.
with Bluetooth
®
wireless technology
Troubleshooting

COMPLIANCE
This product complies with all relevant British and European safety standards:
WIRING
This product is manufactured to class I category and must have an earth connection.
COLOUR CODING:
L - Live = Brown
N - Neutral = Blue
- Earth = Green & Yellow
LIGHTS.
To obtain a replacement LED lamp if faulty or broken contact customer services (see details at
foot of page) quoting product code ML420.
OUTSIDE
ZONES
Installation Procedure
The wall surface must be of suitable strength and construction.
1) Measure the distance between the two fixing holes on the back of the mirror frame.
2) Draw a horizontal line on the wall using a spirit level approximately 60mm from the desired position of
the top of the mirror.
Mark the drill positions on the horizontal line using the dimension taken from step 1. Accurately mark the 2
hole positions with a pencil, drill and fit the wall plugs.
NOTE: The wall plugs supplied are only suitable for solid stone / brick walls. For plasterboard walls use
specialist wall plugs.
3) The next step is to make the electrical connection from the mirror to the mains supply. Use the connec-
tion wire found at the rear of the mirror to make the necessary connections in accordance with the current
IEE regulations. A second person will need to hold the mirror in place whilst electrical connections are
made.
4) Insert the wall screws supplied into the wall plugs. Leave approximately 5-10mm of the screw standing
proud of the wall. Mount the mirror onto the screws fitted to the wall. Ensure mirror is securely mounted.
before leaving unattended.
Strip wires to a suitable
length. DO NOT connect
to a plug & socket outlet.
THIS PRODUCT IS MANUFACTURED TO CLASS I
CATEGORY AND MUST HAVE AN EARTH CONNECTION.
! IF IN DOUBT CONSULT YOUR ELECTRICIAN !
Colour Coding:
L - Live = Brown
N - Neutral = Blue
- Earth = Green & Yellow
The heated pad is on when the light is on. DO NOT leave on for prolonged periods of time.
CLEANING
It is recommended that the unit is cleaned with a soft, dry, non abrasive cloth when turned off. Never use
cleaning agents or abrasive materials on any type of surface finish. Do not allow moisture to come into
contact with the electrical components.
Operating & Aftercare Instructions
Bluetooth
®
Connection and Controls
LIGHT ON / OFF
PREVIOUS TRACK
VOLUME UP
BLUETOOTH ON / OFF
NEXT TRACK
VOLUME DOWN
Pairing Bluetooth
®
enabled devices:
Pairing occurs when two Bluetooth
®
wireless technology enabled devices communicate with each other and
establish a connection. This information is then stored in the memory of each device meaning that once
initially connected, the two devices will not need to pair again.
Your Beat Mirror can link with up to seven separate devices. When this limit is reached any additional devices
paired will erase previous connections to accomodate the new pairing.
Connecting your Bluetooth
®
enabled device to your Beat Mirror:
1. It is recommended that the Bluetooth
®
connectivity of the device you want to pair with your Beat Mirror is
turned on first to make connection easier.
2. Hold down the button for 3 seconds to put your Beat Mirror into pairing mode. The LED indicator light
will flash quickly and will be accompanied with a beep to indicate that pairing mode has been turned on and
the mirror is discoverable.
3. On the selected Bluetooth
®
enabled device select ‘Bluetooth Mirror’ from the Bluetooth
®
device list to
connect to the mirror.
Note: Devices running Bluetooth
®
Version 2.0 or earlier may need to enter a pairing code before a connection
is made. This code is a device default of 0000 or 1234. These devices will not need to enter a pairing code
again after the initial set-up. Some devices may also ask for the connection to be accepted, which will be
prompted on the device screen.
4. The mirror will beep twice to signal that a connection has been made between the two Bluetooth
®
enabled
devices and the indicator light will flash slowly.
5. Once connected, any music played on the paired device will play through the Beat
Mirror.
Tracks can be changed using the and buttons, paused with and volume can be adjusted
with and
6. The lights and heated demister pad can both be turned on with the button. The Bluetooth
®
functions
on the mirror will work regardless of whether the light is turned on.
The Bluetooth
®
connection will automatically cease when the two paired devices are out of range.
To manually turn off the Bluetooth
®
functions on the mirror, press and hold the button for 3 seconds. A
long beep will confirm that Bluetooth
®
functions have been turned off.
www.qssupplies.co.uk