Roper Rhodes SYSTEM Series User manual

SAFETY NOTICE
The unit and basin should be fully secured to a suitably reinforced wall to ensure stability. The wall plugs supplied are only suitable for solid
stone/brick walls. For plasterboard walls use specialist wall plugs along with supplementary wall strengthening as units can be very heavy.
Seek advice from a specialist about the suitability of fixings to be used.
Wear suitable eye protection when drilling. Take care when using power tools near water - the use of a residual current device (RCD) is
recommended. Beware of hidden pipes or cables. Take care when drilling tiled surfaces as the drill might slip. Use a piece of masking tape
to prevent the drill from wandering.
Ensure to follow these instructions to the end, acknowledging final instruction of siliconing basin in position.
Customer Services, Roper Rhodes Ltd, Brassmill Lane Trading Estate, Bath, BA1 3JF
Tel:[phone] | Fax: [phone]
Email: [email protected] | Web: www.roperrhodes.co.uk
SYSTEM
WALL MOUNTED UNIT
Please retain for future use
PAGE 1 OF 4
RR-SYSWM REV : KA/11/2017
Replacement Components
Should you require any replacement components for this product please contact Roper Rhodes using the contact details below.
FURNITURE AFTERCARE INSTRUCTIONS
As with all wooden furniture, this product should be treated with care.
We recommend...
Wipe away any water splashes or condensa-
tion after use. Excessive exposure to water will
deteriorate the furniture.
All bathrooms should be well ventilated with a
suitable extractor fan.
Clean with a soft damp cloth only.
For removal of lime scale deposits use a
suitable proprietary cleaner. If necessary test
on an inconspicuous area first.
WIPE AWAY
Please DO NOT...
BLEACH
CLEANER
CREAM
CLEANER
Do not scrub or scour
Do not use abrasive cleaning agents

Mark the location of each of the wall mounting plates ensuring that they are positioned inside the sidewalls of the vanity unit. For each
mounting plate drill two holes in the marked positions using a 8mm drill bit to a depth of 55mm.
Locate the hangers onto the wall mounting
plates. Wall hangers not only tighten the unit
against the wall (Screw A) but also offer up/down
adjustment to fine-tune the fixing position (Screw
B). Finally fold over flap C to conceal the
adjustment screws on the wall hanger.
B
C
A
Figure 3
WALLMOUNTING THE UNITS
Customer Services, Roper Rhodes Ltd, Brassmill Lane Trading Estate, Bath, BA1 3JF
Tel:[phone] | Fax: [phone]
Email: [email protected] | Web: www.roperrhodes.co.uk
PAGE 2 OF 4
Figure 1
Figure 2
Middle hanger &
fixing for 1200mm
unit only.
SYSTEM
WALL MOUNTED UNIT
Please retain for future use
RR-SYSWM REV : KA/11/2017
NOTE:
When using furniture in conjunction with System
ceramic basins; metal wall hanging brackets need to
be set below back flange of basin. Ensure a minimum
of 5mm clearance from top of bracket to bottom face of
flange. The wall hangers vertical adjustment should be
used to seat well on the brackets. See diagram above.
5mm
Min. Gap

Customer Services, Roper Rhodes Ltd, Brassmill Lane Trading Estate, Bath, BA1 3JF
Tel:[phone] | Fax: [phone]
Email: [email protected] | Web: www.roperrhodes.co.uk
PAGE 3 OF 4
SYSTEM
WALL MOUNTED UNIT
Please retain for future use
RR-SYSWM REV : KA/11/2017
Figure 4 Figure 5
Figure 7
Figure 8
Figure 6
Figure 9
Figure 10
!
REMOVING DRAWER / RE-ATTACHING DRAWER
±1
±2
L
LR
R
To remove the drawer - press and hold in the levers on both
sides of the drawer and slide the drawer from the runners.
When replacing the drawer - ensure that the runners fully engage
at the back of the drawer and an audible click is heard
CLICK
CLICK
DRAWER FRONT ADJUSTMENT / DRAWER FASCIA REMOVAL
Remove the cover caps from the insides
of the drawer on both sides to show the
adjustment panels
Horizontal adjustment. Turn the screws shown until they become
stiff - turning past this point will move the drawer fascia left / right
Vertical adjustment. Turn the screws shown to raise / lower the
drawer front. This can be done on the left and right hand runners.
Fascia removal.
- Insert screwdriver into release mechanism (moving
the shield out of the way) and twist the mechanism on
both sides to release the drawer front.
- To reattach - simple push drawer fascia back into
place (it will click and lock in place).
ONCE ALL ADJUSTMENTS MADE - RE-TIGHTEN LOCKING SCREWS AND REPLACE COVER
CAPS
BEFORE ANY ADJUSTMENTS, LOCKING SCREWS ON BOTH RUNNERS
SHOULD BE UNSCREWED. FAILURE TO DO SO COULD DAMAGE THE
RUNNERS

Customer Services, Roper Rhodes Ltd, Brassmill Lane Trading Estate, Bath, BA1 3JF
Tel:[phone] | Fax: [phone]
Email: [email protected] | Web: www.roperrhodes.co.uk
PAGE 4 OF 4
- Apply a bead of silicone to the basin / worktop on 2 sides to fix to
and protect the side panels as per figure 12.
- Typically the basin also has a silicone bead along the back edges
where it meets the wall (not shown)
- The basin should be held in place while the silicone cures.
BASIN/WORKTOP INSTALLATION
Figure 13
INSTALLING HANDLES
- Remove the drawer as per instructions.
- Included in the box is a template for fixing the handles at our recommended heights.
- Tape this in place in the centre of the front of the drawer front and mark the locations
of the relevant handle holes.
- Clamp a piece of wood on the back of the drawer (being careful not to damage the
front) and drill through carefully from the front. See figure 10.
- Screw handles into place.
- For drawer top handles - simply hold in place centrally on the top of the drawers and
then screw in from behind using small screws provided.
- Re-install drawers ensuring that the drawer box clicks back into place.
Figure 11
Top of drawer
block of wood
INSTALLING OVERFLOW WASTE KIT - For isocast basins only
Kit included with basin
- Follow instructions on overflow waste kit packaging.
- The overflow pipe will need to be cut (as shown on the packaging) to 125mm in length.
This is to avoid clashing with drawer componentry on top drawer. See Figure 11
- Ensure pipe has a watertight fit both on overflow cap, and waste inlet.
125mm
Figure 12
Brace above hanger removed
in figure to show clarity.
SYSTEM
WALL MOUNTED UNIT
Please retain for future use
RR-SYSWM REV : /11/2017