ROSE DISPLAYS CABLE CLIP User manual

35 Congress Street, Salem, MA 01970
Tel# [phone] Fax# [phone]
e-mail:[e-mail]
Parts
SuperSnap™ with Rod Connector
Step 1
Place cable into inner channel of
CableClip. The cable should
snap into place. Fig. 1
Align one end of the CableClip with
the top channel of the plastic holder.
Then insert one round end, press
down on the other round end and
slide CableClip into rail. Fig. 2
Note: Position CableClip about
halfway down each SuperSnap. Fig. 3
Step 2
Push rod halfway into clip rail
of one SuperSnap. Fig. 4
Step 3
Insert rod into top clip rail of second
SuperSnap until both holders meet.
Fig. 5 & 6 Repeat steps 2-3 for
additional SuperSnaps.
Instruction Sheet
Instructions for assembly
Incept-11.13.02
The SuperSnap™ is a trademark of Rose Displays, Ltd. Neither the
manufacturer nor any sales agent may be held liable for injury, loss or
damage resulting from the use of these products.
Part #02INSSuperSnapRodCCLoop
Figure 3
Figure 6
Figure 2Figure 1
Figure 5
Figure 4
Page 1 of 2
SuperSnap
12S300
Cable Clip
06-5050
Loop & Saucer
16-0018SL
End Caps
06-5475
6” Rod
97-0304-06

35 Congress Street, Salem, MA 01970
Tel# [phone] Fax# [phone]
e-mail:[e-mail]
Parts
(continued)
Step 4
Snap all sections of the SuperSnap
open. Fig. 7
Note: It is easier to open and close
the SuperSnap by starting at one
end and working your way down
the holder.
Step 5
Insert poster (top and bottom) into
all sections of SuperSnap. Fig. 8
Step 6
To close, snap the SuperSnap shut.
Fig. 9
Step 7
Push end caps into place. Fig. 10
Step 8
Suspend holders. Finished Look
Important note:
Please save and reuse the
SuperSnap, End Caps and
CableClips for future projects.
Instructions for assembly
Incept-11.13.02
The SuperSnap™ is a trademark of Rose Displays, Ltd. Neither the
manufacturer nor any sales agent may be held liable for injury, loss or
damage resulting from the use of these products.
Part #02INSSuperSnapRodCCLoop
SuperSnap™ with Rod Connector Instruction Sheet
Open all
holders
Finished Look
Page 2 of 2
Figure 10Figure 9
Figure 7 Figure 8
SuperSnap
12S300
Cable Clip
06-5050
Loop & Saucer
16-0018SL
End Caps
06-5475
6” Rod
97-0304-06

Parts
SuperSnap™ with Rod Connector
Step 1
Place cable into inner channel of
CableClip. The cable should
snap into place. Fig. 1
Align one end of the CableClip with
the top channel of the plastic holder.
Then insert one round end, press
down on the other round end and
slide CableClip into rail. Fig. 2
Note: Position CableClip about
halfway down each SuperSnap. Fig. 3
Step 2
Push rod halfway into clip rail
of one SuperSnap. Fig. 4
Step 3
Insert rod into top clip rail of second
SuperSnap until both holders meet.
Fig. 5 & 6 Repeat steps 2-3 for
additional SuperSnaps.
Instruction Sheet
Instructions for assembly
Incept-11.13.02
The SuperSnap™ is a trademark of Rose Displays, Ltd. Neither the
manufacturer nor any sales agent may be held liable for injury, loss or
damage resulting from the use of these products.
Part #02INSSuperSnapRodCCLoop
Figure 3
Figure 6
Figure 2Figure 1
Figure 5
Figure 4
Page 1 of 2
SuperSnap
12S300
Cable Clip
06-5050
Loop & Saucer
16-0018SL
End Caps
06-5475
6” Rod
97-0304-06

Parts
(continued)
Step 4
Snap all sections of the SuperSnap
open. Fig. 7
Note: It is easier to open and close
the SuperSnap by starting at one
end and working your way down
the holder.
Step 5
Insert poster (top and bottom) into
all sections of SuperSnap. Fig. 8
Step 6
To close, snap the SuperSnap shut.
Fig. 9
Step 7
Push end caps into place. Fig. 10
Step 8
Suspend holders. Finished Look
Important note:
Please save and reuse the
SuperSnap, End Caps and
CableClips for future projects.
Instructions for assembly
Incept-11.13.02
The SuperSnap™ is a trademark of Rose Displays, Ltd. Neither the
manufacturer nor any sales agent may be held liable for injury, loss or
damage resulting from the use of these products.
Part #02INSSuperSnapRodCCLoop
SuperSnap™ with Rod Connector Instruction Sheet
Open all
holders
Finished Look
Page 2 of 2
Figure 10Figure 9
Figure 7 Figure 8
SuperSnap
12S300
Cable Clip
06-5050
Loop & Saucer
16-0018SL
End Caps
06-5475
6” Rod
97-0304-06