ROSE DISPLAYS ANOKIOSK WITH BASE RAIL User manual

The AnoKiosk™ is a trademark of Rose Displays, Ltd. Neither the
manufacturer nor any sales agent may be held liable for injury, loss or
damage resulting from the use of these products. Part
#02INAnoKioskRigidBase Rail
Incept-09.20.02
Instruction Sheet
Note:
We recommended that two people
assemble this kiosk.
Step 1a
Slide spine into vertical rail.
Step 1b
Slide another vertical rail onto the
other edge of spine. Repeat for all
vertical rails and spines.
Step 2
Carefully insert corner brackets into
ends of bottom rails, using thumb as
shown in illustration. Two brackets
per end of each rail. Bracket can
bend if forced.
Detail- It is important that the corner
bracket tension tab faces toward
outside of frame. (2b)
AnoKiosk™
Instructions for Assembly
Kiosk spine
06-2175 Corner brackets
Parts
Single rails Split rails
(Continued on other side)
2a 2b
1a 1b
35 Congress Street, Salem, MA 01970
Tel# [phone] Fax# [phone]
e-mail:[e-mail]
Bottom Rails
with Base Rail

The AnoKiosk™ is a trademark of Rose Displays, Ltd. Neither the
manufacturer nor any sales agent may be held liable for injury, loss or
damage resulting from the use of these products. Part
#02INAnoKioskRigidBase Rail
Incept-09.20.02
Instruction Sheet (side 2)
Instructions for Assembly continued
7
Step 3
Lay out the bottom rails on the floor as
they will be configured.
Step 4
Assemble the vertical rail assemblies
onto the upward facing corner brackets
already inserted into the bottom rails.
All four brackets should go into the
vertical rails at one time.
Note: (4 way only) The last vertical
rail will be tensioned. This is normal.
Step 5
Insert corner brackets into ends
of split rails, 1 per end. Use thumb
as shown in illustration.
Step 6
Assemble split rails onto top ends
of vertical rails, one inside and one
outside of each side of the AnoKiosk.
Step 7
Insert and change signs through top
of each side.
AnoKiosk™
3 4
3-Way
4-Way
5 6
35 Congress Street, Salem, MA 01970
Tel# [phone] Fax# [phone]
e-mail:[e-mail]

The AnoKiosk™ is a trademark of Rose Displays, Ltd. Neither the
manufacturer nor any sales agent may be held liable for injury, loss or
damage resulting from the use of these products. Part
#02INAnoKioskRigidBase Rail
Incept-09.20.02
Instruction Sheet
Note:
We recommended that two people
assemble this kiosk.
Step 1a
Slide spine into vertical rail.
Step 1b
Slide another vertical rail onto the
other edge of spine. Repeat for all
vertical rails and spines.
Step 2
Carefully insert corner brackets into
ends of bottom rails, using thumb as
shown in illustration. Two brackets
per end of each rail. Bracket can
bend if forced.
Detail- It is important that the corner
bracket tension tab faces toward
outside of frame. (2b)
AnoKiosk™
Instructions for Assembly
Kiosk spine
06-2175 Corner brackets
Parts
Single rails Split rails
(Continued on other side)
2a 2b
1a 1b
Bottom Rails
with Base Rail

The AnoKiosk™ is a trademark of Rose Displays, Ltd. Neither the
manufacturer nor any sales agent may be held liable for injury, loss or
damage resulting from the use of these products. Part
#02INAnoKioskRigidBase Rail
Incept-09.20.02
Instruction Sheet (side 2)
Instructions for Assembly continued
7
Step 3
Lay out the bottom rails on the floor as
they will be configured.
Step 4
Assemble the vertical rail assemblies
onto the upward facing corner brackets
already inserted into the bottom rails.
All four brackets should go into the
vertical rails at one time.
Note: (4 way only) The last vertical
rail will be tensioned. This is normal.
Step 5
Insert corner brackets into ends
of split rails, 1 per end. Use thumb
as shown in illustration.
Step 6
Assemble split rails onto top ends
of vertical rails, one inside and one
outside of each side of the AnoKiosk.
Step 7
Insert and change signs through top
of each side.
AnoKiosk™
3 4
3-Way
4-Way
5 6